Installation Manual

ManualsBrandsQualGear ManualsAccessories & SuppliesUniversal Projector Wall Mount with Fine Tune Adjustments

Maintenance

Please check that the projector mount is secure and safe to use at regular intervals. If you have any

questions regarding any of the instructions or warnings, please contact your local distributor (OR)

contact QualGear technical support via email at support@qualgear.com.

5 Year Limited Warranty

Version September 2015

5 Year Limited Warranty

Version September 2015

QG-PM-FT1-WHT

www.qualgear.com

ADJUSTABLES: Vertical Tilt, Horizontal Roll, and

Horizontal Rotation: +/- 5 degrees

Horizontal Slide (Forward/Backward): 358 – 658mm,

from the center of the wall plate

Horizontal Slide (Left/Right): 90mm

CAUTION!

Do not exceed the maximum rated weight

specified. Otherwise, serious injury or

property damage may occur.

PROJECTOR WALL MOUNT

INSTALLATION MANUAL

Installing the Wall Plate Covers and the Decorative Cover

Adjusting the Forward/Backward Slide

Locking Screws

W-D

-5°

5°

[Projector not included][Projector not included]

(33lbs)

RATED

15kg

(33lbs)

RATED

15kg

Wall Plate Cover

Connect the cables to the projector, and install

the wall plate covers and the decorative cover.

Decorative Cover

Summary of content (6 pages)

PAGE 1
Adjusting the Forward/Backward Slide Locking Screws 7 QG-PM-FT1-WHT INSTALLATION MANUAL W-D PROJECTOR WALL MOUNT Installing the Wall Plate Covers and the Decorative Cover Wall Plate Cover Connect the cables to the projector, and install the wall plate covers and the decorative cover. [Projector not included] CAUTION! Do not exceed the maximum rated weight specified. Otherwise, serious injury or property damage may occur.
PAGE 2
NOTE Please read the entire installation manual before you start installation and assembly. WARNING  Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual. If you have any questions regarding the instructions, for US customers please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.
PAGE 3
1 Cable Management 3a Mounting to a Wooden Stud Wall NOTE For concrete or brick wall Mounting Bracket mounting, follow Step 3b. Stud Finder Feed the projector cable(s) through the mounting bracket. 2 Wall Checking the Installation Position Short Throw Projectors Regular Projectors 1 2 Using an edge-to-edge stud finder, find the edges of the stud. Using a level, mark the centerline of the stud. T Wall Wall 55mm 65mm 2.5") (2.
PAGE 4
3b Mounting to a Concrete or a Brick Wall Brick Concrete Wall Plate 2 7 8 6 5 1 3 4 10 12 9 11 1 Hold the marking template against the wall where you want to install the projector, mark five holes for drilling. 60mm 0mm (2.4" ) (2 10m ( 3/8") 5. Using a 5mm allen key (W-C), mount the wall plate and fasten with the M6x55mm screws (W-A). 2 Using a power drill and a 3/8" masonry drill bit, drill mounting holes of 3/8" (10 mm) diameter and 2.
PAGE 5
4 Installing the Mounting Bracket onto the Wall Plate Mounting Bracket Wall Plate 1 2 W-E W-C 3 Using 5mm allen key (W-C), attach the mounting bracket to the wall plate with screws (W-E). Place concrete anchor (W-B) in each hole. Tap each anchor flush with the wall using a hammer. Using a 5mm allen key (W-C), mount the wall plate and fasten with the M6x55mm screw (W-A).
PAGE 6
Adjusting the Horizontal Roll According to the type of your projector, choose the appropriate screws, and then attach the projector mounting plate to the projector, with or without the extension arms. WITHOUT EXTENSION ARMS M-A/ M-B/ M-C/ M-D/ M-E/ M-F/ M-G/ M-H/ M-I OR FRONT VIEW Adjustment Direction Adjusting the Horizontal Rotation Top View IMPORTANT: Use an assistant to hold the projector securely while attaching it to the wall mount and/or making adjustments.