User Manual

ManualsBrandsQualGear ManualsAccessories & SuppliesPRB-717-Blk Ceiling Mount Projector Accessory,Black Mount

13.6kg

(30lbs)

RATED

2 Year Limited Warranty2 Year Limited Warranty

Version: September 2017

PRB-717-BLK

Roll Adjustment

To make Roll adjustment, first ensure that weight of the projector is supported.

Then loosen both M6x70mm bolts with the supplied Allen Key (E) and Wrench (F),

and adjust to your desired position. Re-tighten both screws firmly.

Roll +/-20°

Rotation/Shift Adjustment

To make Rotation / Shift adjustment(s), first ensure that weight of the projector is

supported. Then loosen the center M6x16mm screw slightly with the supplied

Wrench (F), and adjust to your desired position. Re-tighten the screw firmly.

Rotation 360°

Shift 1"

Adjusting the Projector (Part 2 of 2)4

Scan the QR Code™ below

for more info about this product:

store.qualgear.com

google.com/+qualgear

youtube.com/qualgear

support@qualgear.com

facebook.com/qualgear

twitter.com/qualgear

pinterest.com/qualgearusa

+1 (972) 423-8960

Summary of content (6 pages)

PAGE 1
4 Adjusting the Projector (Part 2 of 2) PRB-717-BLK Roll Adjustment F E Roll +/-20° To make Roll adjustment, first ensure that weight of the projector is supported. Then loosen both M6x70mm bolts with the supplied Allen Key (E) and Wrench (F), and adjust to your desired position. Re-tighten both screws firmly. Sh ift 1" Rotation/Shift Adjustment F Rotation 360° To make Rotation / Shift adjustment(s), first ensure that weight of the projector is supported.
PAGE 2
NOTE Please read the entire installation manual. Check to ensure that all parts are included before you start installation and assembly. WARNING  Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual. US customers with questions regarding instructions, please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.
PAGE 3
5 1A Installing the Ceiling Mount (Wood Joist Surfaces) For installation to concrete surfaces, skip to Step 1B. Attach ceiling mount with two screws (H) as shown in the figure on the left. Using a socket wrench tighten each screw until the ceiling IMPORTANT: mount is firmly attached. Do not use electric/power drill and do not over tighten the screws. Do not use electric / power drill and do not over tighten the screws. H Using an edge-to-edge stud finder, find the edges of the stud in the ceiling.
PAGE 4
1B Installing the Ceiling Mount (Concrete Surfaces) 3 For installation to wood surfaces, refer to Step 1A. G Anchors 1 H Mounting Screws Hold the marking template provided against the ceiling where you want to install your projector, mark four holes for drilling using a marking pen or pencil. 2 WARNING (64mm) 2.5"  Concrete must be 2000 psi density minimum. 8mm 5/16" Lighter density concrete may not hold concrete anchors.
PAGE 5
2 Attaching the Projector Bracket to the Projector Place the Projector Bracket Assembly over the Projector and align the center of the Mount with the Center of Gravity of the Projector. WARNING TIP  If your projector model has three mounting holes only, please remove the fourth Align the shift adjustment opening (at the center of the projector bracket) in parallel with the projector lens opening to allow shift adjustments to the projector. extension bracket using the supplied Allen Key (E).
PAGE 6
3 4 Attaching the Projector Assembly to the Ceiling Mount Adjusting the Projector (Part 1 of 2) Pitch Adjustment Clearance in the M6x30mm screws to allow for proper fitting with the hook as shown in the diagram on the left. Loosen Tighten E E Pitch +/-30° To make Pitch adjustment, first ensure the weight of the projector is supported. Then loosen both M6x25mm screws with the supplied Allen Key (E), and adjust to your desired position. Re-tighten both screws firmly.