ASSEMBLY INSTRUCTIONS WF198565/198566 SAFETY WARNINGS 1-Follow the information on the waning label appearing on the upper bunk bed and structure on the carton Do not remove warning label from bed 2-Amway use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls. 3-Surface of mattress must be at least 5 inches below the upper edge of guard rails. 4-Do not allow children under 6 years to use the upper bunk bed.
Part List:198565 Lower horizontal bar PCs 1 Upper horizontal bar PCs Q Short side horizontal bar PCs R Horizontal bar (back) 1pc 3 Horizontal bar {front} apes T J Front pane! (left) 1pc Ym Yn) Front panel (lower middle} 1pe Ww — Front panel (right) pe Front panel (upper middle) 1pe x] Top panel apes 15 Upper slat pests T1 i i Decorative brace Zoos u1 Decorative brace apes
Part List:198566 leg back 1pc FB leg front 1pc HB leg back 1pc leg front 1pc Vertical middle front 1pc HB Cap side (front) 1pc G fee Vertical middle back 1pc K Cap middle (front) 1pc L —— Cap middle (front) 1pc J —— HB Cap side (back) 1pc e— Lower side rail (front) 1pc Vem Lower side rail (back) 1pc w Tee ’ Thee— ” Upper side rail (front) 1pc Long side horizontal bar PCs | Stairs vertical right 1pc Upper side rail (back) 1pc Stairs vertical left 1pc = Stairs bridge PCs Hardware List: 198566 210*30mm 214" Wo
STEP 1: Following below illustration Assembly FRAME #1. Using hardware #9 connect T and W front panel (left-right) with T1 short decorative bar to complete FRAME #1LR, And using hardware #9 connect U and V front panel (upper-wore) with U1 long decorative bar to complete FRAME #1UL. 8PC¢ STEP 2: Following below illustration Assembly FRAME #2. Using hardware #8 connect T and W front panel (lief-right) with V and U front peen! {upper-lower middies) to complete FRAME #2.
STEP 3: Following below illustration Assembly FRAME #3. Using hardware #4 connect $ horizontal bar (front) with FRAME #2 to complete FRAME #3. i PCS NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 4: Following below illustration Assembly FRAME #4. Using hardware #1 & #5 connect H vertical middle front with FRAME #3 to complete FRAME #4.
STEP 5: Following below illustration Assembly FRAME #5. Using hardware #8 connect J HB cap side (back) with | HB cap side (front) to complete FRAME #5HB and L cap middle with K cap middle to complete FRAME #5MB. PCS FRAME #5MB NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 6: Following below illustration Assembly FRAME #6. Using hardware #1 & #5 connect Y1 and Y2 stairs vertical Misfit-right with Z stairs bridge to complete FRAME PCS 6PC; 8.
Using hardware #1 & #7 connect A and B FB leg front-back with E and F lower-upper horizontal bar to complete FRAME #7. om STEP 7: Following below illustration Assembly FRAME PCS 8PC; NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 8: Following below illustration Assembly FRAME Using herd wars #1 & #7 connect C and D HB leg front-back with E and F lower-upper horizontal bar y to complete FRAME #8.
STEP 9: Following below illustration Assembly FRAME #9. 6 Using hardware #8 connect FRAME #5HB with FRAME #8 to complete FRAME PCS FRAME #5HB NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 10: Following below illustration Assembly FRAME #10. Using herd wars connect FRAME #7, #9 with M, N, O side rails and y 8 P long side horizontal bar to complete FRAME #10.
STEP 11: Following below illustration Assembly FRAME #11. Using hardware connect R horizontal bar back and G vertical middle back y f to complete FRAME #11. = 1PC| NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 12: Following below illustration Assembly FRAME #12. 5 Using hardware #5 connect O side rail and P long side horizontal bar with G vertical middle back i to complete FRAME #12.
STEP 13: Following below illustration Assembly FRAME #13. Using hardware #1 & #6 connect FRAME #8 with FRAME #4 fo complete FRAME #13. PCS 2PC i TH oN —mr\ NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 14: Following below illustration Assembly FRAME #14. Using hardware #6 connect FRAME #14MB with FRAME #13 to complete FRAME #14.
STEP 15: Following below illustration Assembly FRAME #15. Using hardware #4 connect X top panel with FRAME #14 to complete FRAME #15. NOTE: In this step, DO NOT tighten any bolt until you connect all part together 4PC¢ STEP 16: Following below illustration Assembly FRAME #16. Using hardware #1 & #5 connect FRAME #6 and Q short side horizontal bar with FRAME #15 5 fo complete FRAME #16.
STEP 17: Following below illustration Assembly FRAME #17. Using hardware #5 connect FRAME #6 (Y2 stairs vertical right) with B FB leg front to complete FRAME #17. 3PC: NOTE: In this step, DO NOT tighten any bolt until you connect all part together STEP 18: Following below illustration Assembly FRAME #18. 5 Using hardware #5 connect M upper-lower side rail (front) with Y1 stairs vertical left i to complete FRAME #18.
PCS Using hardware #8 connect to screw all wood slat A1, B1 with FRAME #18 on all the Bed. WARNING!: Please completed screw all the slats in to side rails before using. STEP 19: Following below illustration Assembly FRAME #19.