Mini User Guide Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
© Copyright 2009 Hewlett-Packard Development Company, L.P. Windows is a U.S. registered trademark of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation.
iv Safety warning notice Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Table of contents 1 Hardware features Identifying the hardware ....................................................................................................................... 1 Top components .................................................................................................................. 1 TouchPad ............................................................................................................ 1 Lights ....................................................................
WLAN connection is very weak ......................................................................................... 20 Cannot connect to the wireless router ............................................................................... 20 Connecting to a local area network (LAN) .......................................................................................... 20 3 Multimedia Multimedia features .....................................................................................................
Using pointing devices ....................................................................................................................... 39 Using the TouchPad .......................................................................................................... 39 Connecting an external mouse .......................................................................................... 39 Using the keyboard ...............................................................................................
Resolving a low battery level when the computer cannot exit Hibernation ....................................................................................... 51 Calibrating a battery ........................................................................................................... 51 Step 1: Fully charge the battery ........................................................................ 51 Step 2: Disable Hibernation and Sleep .............................................................
Determining the BIOS version ........................................................................................... 64 Downloading a BIOS update ............................................................................................. 65 Updating programs and drivers .......................................................................................................... 66 13 Setup Utility Starting the Setup Utility .................................................................................
x Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
1 Hardware features Identifying the hardware Components included with the device may vary by region and model. The illustrations in this chapter identify the standard features on most device models. To see a list of hardware installed in the device: 1. Select Start > Control panel > System and Security. 2. In the System area, click Device Manager. You can also add hardware or modify device configurations using Device Manager.
Lights Component (1) Caps lock light On: Caps lock is on. (2) Power light* ● On: The device is on. ● Blinking: The device is in Standby. ● Off: The device is off. ● On: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Off: All wireless devices are off. (3) 2 Description Wireless light Chapter 1 Hardware features Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key. (3) Windows® logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. (5) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Component (1) Description Battery light ● On: A battery is charging. ● Blinking: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly. ● Off: If the device is plugged into an external power source, the light turns off when all batteries in the device are fully charged.
Left-side components Component (1) Description Security cable connector Attaches an optional security cable to the device. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the device from being mishandled or stolen. (2) Power connector Connects an AC adapter. (3) Vent Enables airflow to cool internal components. NOTE: The device fan starts up automatically to cool internal components and prevent overheating.
Display components Component Description (1) Internal display switch Turns off the display if the display is closed while the power is on. (2) Webcam light On: The webcam is in use. (3) Webcam Captures still photographs and videos. NOTE: To capture videos, you will need to install additional webcam software. (4) 6 Internal microphone Chapter 1 Hardware features Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/ Records and captures sound.
Bottom components Component Description (1) Battery release latches (2) Release the battery from the battery bay. (2) Battery bay Holds the battery. (3) Vents (3) Enable airflow to cool internal components. NOTE: The device fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (4) Memory module compartment Contains the memory module slot and a wireless LAN module slot.
Wireless antennas NOTE: For optimal transmission, keep the areas immediately around the antennas free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region. These notices are located in Help and Support. Additional hardware components 8 Component Description (1) Power cord* Connects an AC adapter to an AC outlet.
Component Description (3) Converts AC power to DC power. AC adapter *Batteries and power cords vary in appearance by region and country. Identifying the labels The labels affixed to the device provide information you may need when you troubleshoot system problems or travel internationally with the device. ● Service tag—Provides important information including the following: ◦ Product name (1). This is the product name affixed to the front of your device. ◦ Serial number (s/n) (2).
2 Wireless and local area network Using wireless devices Wireless technology transfers data across radio waves instead of wires. Your computer may be equipped with one or more of the following wireless devices: ● Wireless local area network (WLAN) device—Connects the computer to wireless local area networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices, your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
HP Connection Manager Opens HP Connection Manager, which enables you to create a connection with an HP Mobile Broadband device (select models only). Wired network (connected) Indicates that one or more of your network drivers are installed and one or more network devices are connected to the network.
Using Wireless Assistant software (select models only) A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is disabled in the Setup Utility, it must be reenabled in the Setup Utility before it can be turned on or off using Wireless Assistant. NOTE: Enabling or turning on a wireless device does not automatically connect the computer to a network or a Bluetooth-enabled device.
Using a WLAN With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other computers and accessories that are linked by a wireless router or a wireless access point. NOTE: The terms wireless router and wireless access point are often used interchangeably. ● A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions.
network, other WLAN devices can pick up unprotected signals and either connect to your network (uninvited) or capture information being sent across it. However, you can take precautions to protect your WLAN: ● Use a wireless transmitter with built-in security Many wireless base stations, gateways, or routers provide built-in security features such as wireless security protocols and firewalls. With the correct wireless transmitter, you can protect your network from the most common wireless security risks.
More information about using a WLAN is available through the following resources: ● Information from your ISP and the manufacturer's instructions included with your wireless router and other WLAN equipment ● Information and Web site links provided in Help and Support For a list of public WLANs near you, contact your ISP or search the Web. Web sites that list public WLANs include Cisco Internet Mobile Office Wireless Locations, Hotspotlist, and Geektools.
Inserting a SIM CAUTION: To prevent damage to the connectors, use minimal force when inserting a SIM. To insert a SIM: 1. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 2. Close the display. 3. Disconnect all external devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5.
5. Turn the computer upside down on a flat surface, with the battery bay toward you. 6. Remove the battery. 7. Press in on the SIM (1), and then remove it from the slot (2). 8. Replace the battery. 9. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer.
Troubleshooting wireless connection problems Some possible causes for wireless connection problems include the following: ● Network configuration (SSID or security) has been changed. ● Wireless device is not installed correctly or has been disabled. ● Wireless device or router hardware has failed. ● Wireless device encountered interference from other devices. NOTE: Wireless networking devices are included with select computer models only.
Network icon for WLAN is not displayed If the network status icon is not displayed in the notification area after you configure the WLAN, the software driver is either missing or corrupted. A Windows “Device not Found” error message may also be displayed. The driver must be reinstalled. Get the latest version of the WLAN device software and drivers for your computer from the HP Web site at http://www.hp.com.
WLAN connection is very weak If the connection is very weak, or if your computer cannot make a connection to a WLAN, minimize interference from other devices, as follows: ● Move your computer closer to the wireless router or access point. ● Temporarily disconnect devices such as a microwave, cordless phone, or cellular phone to be sure that other wireless devices are not interfering. 1. Select Start > Control Panel > Network and Internet > Network and Sharing Center. 2.
2. Plug the other end of the cable into a network wall jack (2). Connecting to a local area network (LAN) Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
3 Multimedia Multimedia features Your device includes multimedia features that allow you to listen to music, watch movies, and view pictures. Your device may include the following multimedia components: ● Integrated speakers for listening to music ● Integrated webcam that allows you to capture photographs and videos ● Preinstalled multimedia software that allows you to play and manage your music, movies, and pictures NOTE: Your device may not include all of the components listed.
Component Description (1) Internal microphone Records and captures sound. (2) Webcam Captures still photographs and videos. NOTE: To capture videos, you will need to install additional webcam software. (3) Webcam light On: The webcam is in use. (4) Speakers (2) Produce sound. (5) Volume up hotkey Increases device sound when pressed in combination with the fn key. (6) Volume down hotkey Decreases device sound when pressed combination with the fn key.
◦ ● To increase volume, press fn+f11. Windows volume control: a. Click the Speakers icon in the notification area, at the far right of the taskbar. b. Increase or decrease the volume by moving the slider up or down. Click the Mute Speakers icon to mute the volume. – or – a. Right-click the Speakers icon in the notification area, and then click Open Volume Mixer. b. In the Volume Control column, you can increase or decrease the volume by moving the slider up or down.
Using other preinstalled multimedia software To locate other preinstalled multimedia software: ▲ Select Start > All Programs, and then open the multimedia program you want to use. For example, if you want to use Windows Media Player (select models only), click Windows Media Player. NOTE: Some programs may be located in subfolders. Installing multimedia software from the Internet ▲ To install multimedia software from the Internet, go to the software manufacturer’s Web site and follow the instructions.
You should hear sound through the speakers or through connected headphones. To check the record functions of the device, follow these steps: 1. Select Start > All Programs > Accessories > Sound Recorder. 2. Click Start Recording and speak into the microphone. Save the file to your desktop. 3. Open a multimedia program and play back the sound. NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise.
Connecting an HDMI device The device includes an HDMI (High Definition Multimedia Interface) port. The HDMI port connects the device to an optional video or audio device, such as a high-definition television, or any compatible digital or audio component. NOTE: To transmit video signals through the HDMI port, you need an HDMI cable (purchased separately).
NOTE: To capture videos, you will need to install additional webcam software. For optimum performance, observe the following guidelines while using the webcam: 28 ● If you are having trouble viewing or sending multimedia files to someone on another LAN or outside your network firewall, temporarily disable the firewall, perform the task you want to perform, and then reenable the firewall.
4 Digital cards Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other devices. The SD Card Reader supports the following formats: ● MultiMediaCard (MMC) ● Secure Digital (SD) Memory Card Inserting a digital card CAUTION: To avoid damaging the digital card or the device, do not insert any type of adapter into the SD Card Reader.
Stopping and Removing a digital card CAUTION: To prevent loss of data or an unresponsive system, use the following procedure to safely remove the digital card. 1. Save your information and close all programs associated with the digital card. NOTE: To stop a data transfer, click Cancel in the operating system Copying window. 2. To remove a digital card: a. Click the Safely Remove Hardware and Eject Media icon in the notification area, at the far right of the taskbar.
5 USB devices Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Devices can be connected to the system, an optional docking device, or an optional expansion product. Some USB devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions.
To remove a USB device: 1. Click the Safely Remove Hardware and Eject Media icon in the notification area, at the far right of the taskbar. NOTE: To display the Safely Remove Hardware and Eject Media icon, click the Show hidden icons icon (the arrow at the left of the notification area). 2. Click the name of the device in the list. NOTE: You are prompted that it is safe to remove the hardware device. 3. Remove the device.
3. Click Stop, and then click OK. 4. Remove the HP Mini Mobile Drive. Using the HP Mobile Drive (select models only) Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
6 Drives Identifying installed drives To view the drives installed on the device, select Start > Computer. Handling drives Drives are fragile device components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply.
USB drives include the following types: ● 1.44-megabyte diskette drive ● Hard drive module (a hard drive with an adapter attached) ● DVD-ROM Drive ● DVD/CD-RW Combo Drive ● DVD+RW/R and CD-RW Combo Drive ● DVD±RW/R and CD-RW Combo Drive Using optional external devices NOTE: For more information about required software and drivers, or to learn which device port to use, refer to the manufacturer's instructions.
7 Memory modules The device has one memory module compartment, which is located on the bottom of the device. The memory capacity of the device can be upgraded by replacing the existing memory module in the primary memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
9. Remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 10.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 11. Align the tabs on the memory module compartment cover with the notches on the device, and then close the cover (1). 12. Tighten the 2 cover screws (2). 13. Replace the battery. 14.
8 Pointing devices and keyboard Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Devices and Printers. Then, right-click the device representing your device, and select Mouse Using pointing devices Using the TouchPad To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer to go.
Function Hotkey Initiate Standby. fn+f1 Switch the image. fn+f2 Decrease screen brightness. fn+f3 Increase screen brightness. fn+f4 Initiate QuickLock. fn+f6 Mute device sound. fn+f8 Decrease device sound. fn+f10 Increase device sound. fn+f11 To use a hotkey command on the device keyboard, follow either of these steps: ● Briefly press the fn key, and then briefly press the second key of the hotkey command.
The device must be on before you can initiate Standby. NOTE: If a critical battery level occurs while the device is in Standby, the device initiates Hibernation and the information stored in memory is saved to the hard drive. The factory setting for critical battery action is Hibernate, but this setting can be changed in advanced power settings. To exit Standby, briefly slide the power switch. The function of the fn+f1 hotkey can be changed.
Decreasing speaker sound (fn+f10) Press fn+f10 to decrease speaker sound. Hold down the hotkey to decrease speaker sound incrementally. Increasing speaker sound (fn+f11) Press fn+f11 to increase speaker sound. Hold down the hotkey to increase speaker sound incrementally. 42 Chapter 8 Pointing devices and keyboard Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
9 Power management Setting power options Using power-saving states The computer has two power-saving states enabled at the factory: Sleep and Hibernation. When Sleep is initiated, the power lights blink and the screen clears. Your work is saved to memory, letting you exit Sleep faster than exiting Hibernation. If the computer is in the Sleep state for an extended period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates Hibernation.
Initiating and exiting Hibernation The system is set at the factory to initiate Hibernation after 1,080 minutes (18 hours) of inactivity when running on both battery power and external power, or when the battery reaches a critical battery level. Power settings and timeouts can be changed using Power Options in Windows Control Panel. To initiate Hibernation: ▲ Click Start, click the arrow next to the Shut down button, and then click Hibernate. To exit Hibernation: ▲ Briefly press the power button.
Selecting a different power plan ▲ Click the battery meter icon in the notification area, and then select a power plan from the list. – or – Select Start > Control Panel > System and Security > Power Options, and then select a power plan from the list. Customizing power plans 1. Click the battery meter icon in the notification area and then click More power options. – or – Select Start > Control Panel > System and Security > Power Options. 2. Select a power plan, and then click Change plan settings.
When you connect the device to external AC power, the following events occur: ● The battery begins to charge. ● If the device is turned on, the battery meter icon in the notification area changes appearance. When you disconnect external AC power, the following events occur: ● The device switches to battery power. ● The display brightness is automatically decreased to save battery life. To increase display brightness, press the fn+f8 hotkey or reconnect the AC adapter.
To test the AC adapter: 1. Remove the battery from the device. 2. Connect the AC adapter to the device, and then plug it into an AC outlet. 3. Turn on the device. ● If the power light turns on, the AC adapter is working properly. Contact technical support for information on obtaining a replacement AC power adapter. Using battery power When a charged battery is in the computer and the computer is not plugged into external power, the computer runs on battery power.
To run Battery Check: 1. Connect the AC adapter to the computer. NOTE: The computer must be connected to external power for Battery Check to function properly. 2. Select Start > Help and Support > Troubleshoot > Power, Thermal and Mechanical >Battery Check. Battery Check examines the battery and its cells to see if they are functioning properly, and then reports the results of the examination.
4. Slide the battery release latches (1) to release the battery, and then remove the battery (2). Charging a battery WARNING! Do not charge the computer battery while you are onboard aircraft. The battery charges whenever the computer is plugged into external power through an AC adapter, an optional power adapter, an optional expansion product, or an optional docking device. The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
Maximizing battery discharge time Battery discharge time varies depending on the features you use while on battery power. Maximum discharge time gradually shortens, as the battery storage capacity naturally degrades. Tips for maximizing battery discharge time: ● Lower the brightness on the display. ● Check the Power saver setting in Power Options. ● Remove the battery from the device when it is not being used or charged. ● Store the battery in a cool, dry location.
Resolving a low battery level CAUTION: To reduce the risk of losing information when the computer reaches a critical battery level and has initiated Hibernation, do not restore power until the power lights turn off. Resolving a low battery level when external power is available ▲ Connect one of the following devices: ● AC adapter ● Optional expansion product or docking device ● Optional power adapter Resolving a low battery level when a charged battery is available 1.
To fully charge the battery: 1. Insert the battery into the device. 2. Connect the device to an AC adapter, optional power adapter, optional expansion product, or optional docking device, and then plug the adapter or device into external power. The battery light on the device turns on. 3. Leave the device plugged into external power until the battery is fully charged. The battery light on the device turns off. Step 2: Disable Hibernation and Sleep 1.
Step 4: Fully recharge the battery To recharge the battery: 1. Plug the device into external power and maintain external power until the battery is fully recharged. When the battery is recharged, the battery light on the device turns off. You can use the device while the battery is recharging, but the battery will charge faster if the device is off. 2. If the device is off, turn it on when the battery is fully charged and the battery light has turned off.
Calibrate a battery before using it if it has been stored for one month or more. Disposing of a used battery WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. For additional information, refer to the Regulatory, Safety and Environmental Notices included with this device. Shutting down the device CAUTION: Unsaved information will be lost when the device is shut down.
10 Security Protecting the device Standard security features provided by the Windows operating system and the non-Windows Setup Utility can protect your personal settings and data from a variety of risks. Follow the procedures in this chapter to use the following features: ● Passwords ● Firewall software ● Critical security updates NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks or prevent the device from being mishandled or stolen.
Use the following tips for creating and saving passwords: ● When creating passwords, follow requirements set by the program. ● Write down your passwords and store them in a secure place away from the device. ● Do not store passwords in a file on the device. ● Do not use your name or other personal information that could be easily discovered by an outsider. The following sections list Windows and Setup Utility passwords and describe their functions.
Administrator password Your administrator password protects the configuration settings and system identification information in Setup Utility. After this password is set, you must enter it each time you access Setup Utility. Your administrator password is not interchangeable with an administrator password set in Windows, nor is it displayed as it is set, entered, changed, or deleted. Be sure that you record your password and store it in a safe place.
Managing a power-on password To set, change, or delete this password, follow these steps: 1. Open the Setup Utility by turning on or restarting the device, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select Security > Set Power-On Password, and then press enter. 3. ● To set a power-on password, type your password in the Enter New Password and Confirm New Password fields, and then press enter.
Installing critical updates CAUTION: Microsoft sends alerts regarding critical updates. To protect the device from security breaches and device viruses, install all critical updates from Microsoft as soon as you receive an alert. Updates to the operating system and other software may have become available after the device was shipped. To be sure that all available updates are installed on the device, observe these guidelines: ● Run Windows Update as soon as possible after you set up your device.
11 Backup and recovery Recovery after a system failure is as complete as your most current backup. HP recommends that you create recovery discs immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
Note the following guidelines before creating recovery discs: ● You will need high-quality DVD-R, double-layer DVD-R, DVD+R, double-layer DVD+R, BD-R (writable Blu-ray), or CD-R discs. All these discs are purchased separately. DVDs and BDs have a much higher capacity than CDs. If you use CDs, up to 20 discs may be required, whereas only a few DVDs or BDs are required.
To copy the screen and paste it into a word-processing document, follow these steps: a. Display the screen. b. Copy the screen: To copy only the active window, press alt+fn+prt sc. To copy the entire screen, press fn+prt sc. c. Open a word-processing document, and then select Edit > Paste. Using system restore points When you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time.
Performing a recovery NOTE: You can recover only files that you have previously backed up. HP recommends that you use HP Recovery Manager to create an entire drive backup as soon as you set up your computer. Recovery Manager software allows you to repair or restore the system if you experience system failure or instability. Recovery Manager works from recovery discs or from a dedicated recovery partition (select models only) on the hard drive.
12 Software updates Updated versions of the software provided with your device may be available on the HP Web site. Most software and BIOS updates on the HP Web site are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file. To update the software, follow these steps, which are explained in the remainder of this guide: 1.
Downloading a BIOS update CAUTION: To prevent damage to the device or an unsuccessful installation, download and install a BIOS update only when the device is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the device is running on battery power, docked in an optional docking device, or connected to an optional power source.
Updating programs and drivers To download and install software other than a BIOS update, follow these steps: 1. Access the page on the HP Web site that provides software for your device: Select Start > Help and Support, and then select the software and drivers update. 2. Follow the instructions on the screen to find the software you want to update. 3. At the download area, select the software you want to download and follow the instructions on the screen.
13 Setup Utility Starting the Setup Utility The Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working. The utility reports information about the device and provides settings for startup, security, and other preferences.
Displaying system information The following procedure explains how to display system information in the Setup Utility. If the Setup Utility is not open, begin at step 1. If the Setup Utility is open, begin at step 2. 1. Open the Setup Utility by turning on or restarting the device, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen. 2. Select the Main menu.
Main menu Select To do this System information ● View and change the system time and date. ● View identification information about the device. ● View specification information about the processor, memory size, and system BIOS. Security menu Select To do this Administrator password Enter, change, or delete an administrator password. Power-On Password Enter, change, or delete a power-on password. System Configuration menu Select To do this Language Support Change the Setup Utility language.
Diagnostics menu 70 Select To do this Hard Disk Self Test (select models only) Run a comprehensive self-test on the hard drive. Memory Test Run a diagnostic test on the system memory. Chapter 13 Setup Utility Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Index A AC adapter connecting 46 identifying 9 testing 46 administrator password creating 57 entering 57 managing 57 airport security devices 34 antennas 8 applications key, Windows 3 audio devices, connecting external 25 audio functions, checking 25 audio-in (microphone) jack 4, 23 audio-out (headphone) jack 4, 23 B backing up customized window, toolbar, and menu bar settings 61 personal files 61 templates 61 backup suggestions 61 battery calibrating 51 charging 49, 51 conserving power 53 discharging 50 di
hard drive 7 hard drive self test 70 hard drive, external 34 hardware, identifying 1 HDMI port 27 HDMI port, identifying 5 HDMI, connecting 27 headphone (audio-out) jack 4, 23 headphones 4, 23 Hibernation exiting 44 initiated during critical battery level 50 initiating 44 high-definition devices, connecting 27 hotkeys decreasing screen brightness 41 decreasing speaker sound 42 description 39 increasing screen brightness 41 increasing speaker volume 42 initiating QuickLock 41 initiating Standby 40 muting spe
ports expansion 26 external monitor 4 HDMI 5, 27 USB 5, 31 power connecting 46 conserving 53 power connector, identifying 5 power cord, identifying 8 power light, identifying 2 power-on password creating 58 entering 58 managing 58 Processor C4 State 69 product name and number, device 9 programs, updating 66 projector, connecting 26 public WLAN connection 14 Q QuickLock 56 QuickLock hotkey 41 R readable media 43 recovering a program or driver 60 recovering from the dedicated recovery partition 63 recovering
writable media 43 WWAN device 15 74 Index Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
