User's Manual

ManualsBrandsQualcomm Technologies ManualsElectronics802.11bg, BT, WWAN Combo Module

FENWAY-2 Global User Guide for UMTS/GSM

80-JA863-1 Rev. A

June 2010

Submit technical questions at:

https://support.cdmatech.com

Restricted Distribution. Not to be distributed to anyone who is not an employee of either QUALCOMM or a

subsidiary of QUALCOMM without the express approval of QUALCOMM's Configuration Management.

Not to be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the

express written permission of QUALCOMM Incorporated.

QUALCOMM is a registered trademark of QUALCOMM Incorporated in the United States and may be registered in

other countries. Other product and brand names may be trademarks or registered trademarks of their respective

owners. CDMA2000 is a registered certification mark of the Telecommunications Industry Association, used under

license. ARM is a registered trademark of ARM Limited. QDSP is a registered trademark of QUALCOMM

Incorporated in the United States and other countries.

This technical data may be subject to U.S. and international export, re-export, or transfer ("export") laws. Diversion

contrary to U.S. and international law prohibited.

QUALCOMM Incorporated

5775 Morehouse Drive

San Diego, CA 92121-1714

U.S.A.

QUALCOMM Confidential and Proprietary

Summary of content (21 pages)

PAGE 1
FENWAY-2 Global User Guide for UMTS/GSM 80-JA863-1 Rev. A June 2010 Submit technical questions at: https://support.cdmatech.com QUALCOMM Confidential and Proprietary Restricted Distribution. Not to be distributed to anyone who is not an employee of either QUALCOMM or a subsidiary of QUALCOMM without the express approval of QUALCOMM's Configuration Management.
PAGE 2
Customer Affirmation for Technical Support* In order to facilitate Qualcomm’s compliance with a U.S. Federal Court injunction ruling dated 12/31/2007, acknowledgement of the following is required from each customer seeking technical assistance. Customer confirms that this support request is for a wireless terminal made, sold and used solely outside the USA if it falls within the following table: UMTS Qualcomm will not support for the U.S.
PAGE 3
Contents 1 Introduction 1.1 1.2 1.3 Documentation overview ....................................................................................... 7 Application description .......................................................................................... 8 Terms and acronyms............................................................................................... 9 2 External Connections 3 DC Power and FENWAY-2 Operating Modes 3.1 3.2 3.3 4 RF Integration 4.1 4.2 4.3 4.4 4.
PAGE 4
FENWAY-2 Global User Guide for UMTS/GSM Contents Figures Figure 2-1 External connections — Front View ............................................................. 13 Figure 2-2 External connections — Back View.............................................................. 13 Figure 4-1 FENWAY-2 shields....................................................................................... 17 80-JA863-1 Rev. A 4 QUALCOMM Confidential and Proprietary MAY CONTAIN U.S.
PAGE 5
FENWAY-2 Global User Guide for UMTS/GSM Contents Tables Table 1-1 Table 1-2 Table 1-3 Table 1-4 Table 2-1 Table 3-1 Table 4-1 FENWAY-2 documentation ............................................................................. 7 Reference documents....................................................................................... 7 Reference documents....................................................................................... 8 Terms and acronyms ...........................................
PAGE 6
Revision history Revision Date A June 2010 Description Initial release 80-JA863-1 Rev. A 6 QUALCOMM Confidential and Proprietary MAY CONTAIN U.S.
PAGE 7
1 Introduction 1.1 Documentation overview The Fenway-2 Module is a data and voice enabled wireless module using the Windows Mobile operating system. This module solution delivers WWAN data and voice connectivity for the UMTS (HSDPA and HSUPA), and GSM/GPRS/EDGE protocols, Bluetooth and 802.11b/g connectivity, plus GPS position location, in a single package. This FENWAY-2 global regulatory user guide is organized as follows: Chapter 1 Provides an overview of FENWAY-2 documentation.
PAGE 8
FENWAY-2 Global User Guide for UMTS/GSM 1.2 Introduction Application description The FENWAY-2 module includes a small circuit board support all functionality and the associated software suite.
PAGE 9
FENWAY-2 Global User Guide for UMTS/GSM Table 1-3 Reference documents (continued) Ref No. 1.3 Introduction Document [4] Universal Serial Bus Specification, Revision 2.0 [5] Protection of Electrical and Electronic Parts, Assemblies, and Equipment (ANSI/ESD S20.20-1999) Terms and acronyms Table 1-4 defines the terms and acronyms used throughout this document.
PAGE 10
FENWAY-2 Global User Guide for UMTS/GSM Introduction Table 1-4Terms and acronyms (continued) Term Definition USB Universal serial bus USIM Universal subscriber identity module WCDMA Wideband Code Division Multiple Access WLAN Wideband local area network WWAN Wireless wide area network 80-JA863-1 Rev. A 10 QUALCOMM Confidential and Proprietary MAY CONTAIN U.S.
PAGE 11
2 External Connections The FENWAY-2 add-in card is compatible with the PCI Express Mini Card 52-pin card edge type connector. The PCI Express Mini Card connector pin assignments are listed in Table 2-1.
PAGE 12
FENWAY-2 Global User Guide for UMTS/GSM Table 2-1 External Connections Card connector pin assignments Pin Name Pin Name 28 SDC1_DATA_CONN(2) 88 PMIC_VCOIN 29 LINE_OUT_L_CONN 89 CAMIF_PCLK_FLT 30 SDC1_DATA_CONN(3) 90 VBATT_GND 31 GND 91 CAMIF_HSYNC_FLT 32 SDC1_CLK_TF 92 VBATT_GND 33 GND 93 CAMIF_VSYNC_FLT 34 SDC1_CMD_TF 94 VBATT_GND 35 MDDI_P_DATA_M 95 VREG_CAM_DCORE 36 KEYSENSE_N1_FLT 96 CAM_RESET_N_FLT 37 MDDI_P_DATA_P 97 VREG_CAM_ACORE 38 KEYSENSE_N2_FLT 9
PAGE 13
FENWAY-2 Global User Guide for UMTS/GSM Figure 2-1 External connections — Front View Figure 2-2 External connections — Back View External Connections 80-JA863-1 Rev. A 13 QUALCOMM Confidential and Proprietary MAY CONTAIN U.S.
PAGE 14
3 DC Power and FENWAY-2 Operating Modes 3.1 DC power source DC input is provided by either an external DC source providing 4.6V/1.5A or battery DC source with a max input voltage of 4.2V. Power management system on the FENWAY-2 module accepts these input voltages and regulates as necessary to manage the module operation. 3.2 FENWAY-2 operating modes Example FENWAY-2 module operating modes and their expected data throughput rates are summarized in Table 3-1.
PAGE 15
FENWAY-2 Global User Guide for UMTS/GSM DC Power and FENWAY-2 Operating Modes QUALCOMM products must be handled according to the ESD Association standard: ANSI/ESD S20.20-1999, Protection of Electrical and Electronic Parts, Assemblies, and Equipment. FENWAY electrostatic discharge (ESD) performance is specified in FENWAY Regulatory Test Plan (80-JA852-1). 80-JA863-1 Rev. A 15 QUALCOMM Confidential and Proprietary MAY CONTAIN U.S.
PAGE 16
4 RF Integration 4.1 RF operating frequencies The FENWAY-2 RF operating frequencies are summarized in Table 4-1.
PAGE 17
FENWAY-2 Global User Guide for UMTS/GSM   4.3 RF Integration If Rx diversity and GPS position location are not supported, leave the unused secondary antenna unconnected. RF Feed points. The primary and secondary, GPS, Bluetooth and WLAN antenna feed point locations are identified in Figure 2-1. These can be used to integrate antenna elements directly to the FENWAY-2 module without coaxial cables which may result in a smaller overall system solution.
PAGE 18
FENWAY-2 Global User Guide for UMTS/GSM NOTE RF Integration These FENWAY-2 shields must not be removed. The host device is a hostile environment for RF transceivers, making the shields absolutely necessary. Potential interference sources include the following:  Noise or ripple on the DC power supply voltage input lines, including transients due to switching-mode power supplies or host operating mode changes.
PAGE 19
5 Standards and Regulatory Compliance 5.1 Standards and certification The FENWAY-2 module conforms to the following standards and certification requirements:  UMTS (WCDMA)   GSM    RF.TS/2.1.E.0 WLAN   TS 45.005 BT   TS 25.101 802.
PAGE 20
FENWAY-2 Global User Guide for UMTS/GSM – EN 301 607-1 – GSM900/GSM1800 – EN 300 328 - WLAN & BT CTIA/GCF/PTCRB  Safety  5.2.1 EN 301 511 – GSM900/GSM1800   5.2 – Standards and Regulatory Compliance EN 50360/61 full carrier certification (carriers TBD) RoHS compliance Regulatory information Safety warnings Do not operate the FENWAY-2 module in the following environments: 5.2.
PAGE 21
FENWAY-2 Global User Guide for UMTS/GSM  PCS band < 0 dBi  UMTS band < 0 dBi  ISM band < 2.0 dBi Standards and Regulatory Compliance 4. Independent FENWAY-2 module operation — the FENWAY-2 module must not be co-located or jointly operated with any other transmitter or antenna within the host device. 5.