HP TouchSmart User Guide TouchSmart tm2 Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
© Copyright 2009 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. Product notice This user guide describes features that are common to most models. Some features may not be available on your computer. The information contained herein is subject to change without notice.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Table of contents 1 Getting started Charging the battery ............................................................................................................................. 1 Identifying the installed hardware and software ................................................................................... 1 Identifying hardware ............................................................................................................ 1 Identifying software ........................................
Using the Windows Connect to the Internet Wizard .......................................................... 16 Creating a wireless connection .......................................................................................................... 16 Identifying wireless icons and controls .............................................................................. 16 Identifying wireless and network status icons ................................................... 16 Using the wireless key ..............
Using the hotkeys ............................................................................................................................... 33 7 Multimedia Using the media activity keys ............................................................................................................. 35 Multimedia software ........................................................................................................................... 36 Using HP TouchSmart software or HP MediaSmart software .....
Resolving a low battery level when a charged battery is available ........................................................................................... 49 Resolving a low battery level when no power source is available ........................................................................................... 49 Resolving a low battery level when the computer cannot exit Hibernation ....................................................................................... 49 Calibrating a battery .......
Setting passwords in Windows .......................................................................................... 67 Setting passwords in Setup Utility ..................................................................................... 67 Administrator password ..................................................................................... 68 Managing an administrator password ............................................... 68 Entering an administrator password ................................
Determining the BIOS version ........................................................................... 80 Downloading a BIOS update ............................................................................. 81 Appendix A Product information Input power ......................................................................................................................................... 83 Operating environment ...........................................................................................
1 Getting started Charging the battery To fully charge the battery, leave the computer plugged into external power until the battery light on the computer turns white. WARNING! To reduce the risk of electric shock or damage to your equipment, observe these guidelines: Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer).
Rotating the display To use the computer in slate mode: 1. Open the display. 2. Rotate the display clockwise 180 degrees. 3. Lower the display over the keyboard. CAUTION: To reduce the risk of damage to your computer, do not force the display past 180 degrees, and do not transport the computer while it is in slate mode. 2 Chapter 1 Getting started Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Finding more information Locating Help and Support In addition to the user guides, Help and Support provides information about the operating system, power management, software updates, networking, drivers, troubleshooting tools, and accessing technical support. NOTE: You do not need to connect to the Internet to access the user guides in Help and Support. To access Help and Support: Select Start > Help and Support. – or – For country- or region-specific support, go to http://www.hp.
2 What's next After you set up and register the computer, it is important to take the next steps in this chapter before you begin using the computer. For help in identifying specific components of the computer, refer to Features on page 8. Creating recovery discs After setting up the computer, one of the first and most important steps to take is to create a set of recovery discs of the full factory image.
ł Video—You can connect an optional display device or an HDMI (High Definition Multimedia Interface) device to the computer. You can also connect an optional optical drive. For more information about the video features, refer to Video on page 40. ł Webcam—Adjustable, with low-light image technology and built-in microphones, the webcam is a perfect companion to your instant messaging program. For more information on the webcam, refer to Webcam on page 38.
3 Using Instant Web HP Instant Web provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of sliding the power switch and you can rapidly access several applications without the need to start the main operating system. If you like to browse the Internet, view digital photos, listen to music, or keep in touch through e-mail, instant messages, or Skype (select models only), you will enjoy the many features of HP Instant Web.
NOTE: Clicking on the Make Windows your default Power On experience in this dialog box disables Instant Web. For more information on disabling and enabling Instant Web, refer to Disabling and enabling HP Instant Web on page 7. Disabling and enabling HP Instant Web You can disable or reenable Instant Web in two ways. To disable or reenable Instant Web from the Windows operating system: 1. Click Start > All Programs > HP Instant Web. The HP Instant Web Installer folder displays. 2.
4 Features Components Top components TouchPad Component Description (1) TouchPad on/off button Turns the TouchPad on and off. Lightly press the button and hold for 3 seconds to turn the TouchPad on and off. (2) Left TouchPad button* Functions like the left button on an external mouse. (3) Right TouchPad button* Functions like the right button on an external mouse. (4) TouchPad* Moves the pointer and selects or activates items on the screen. *This table describes factory settings.
Right-side components Component Description (1) Fingerprint reader Allows a fingerprint logon to Windows instead of a password logon. (2) Rotate button Rotates the screen image counter-clockwise into 4 orientations: landscape primary, portrait primary, landscape secondary, and portrait secondary. (3) Power light ł White: The computer is on. ł Blinking white: The computer is in the Sleep state. ł Off: The computer is off or in Hibernation.
Component (7) Description Digital Media Slot Supports the following digital card formats: ł Memory Stick ł Memory Stick Pro ł MultiMediaCard ł Secure Digital Memory Card ł xD-Picture Card (8) USB ports (2) Connect optional USB devices. (9) Battery light ł Off: The computer is running on battery power. ł Blinking amber: The battery has reached a low battery level, a critical battery level, or there is a battery error. ł Amber: A battery is charging.
Component Description Security cable slot (5) Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. Pen holder (6) Holds the pen. Display components Component Description (1) WWAN antennas (2)* Send and receive wireless signals to communicate with wireless wide-area networks (WWAN).
Bottom components Component Description (1) Battery release latch Releases the battery from the battery bay. (2) Battery bay Holds the battery. NOTE: The battery is preinstalled in the battery bay at the factory. (3) Vents (4) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. 14 (4) Hard drive bay Holds the hard drive.
5 Networking The computer supports 2 types of Internet access: ł Wireless—For mobile Internet access, you can use a wireless connection. To learn about adding the computer to an existing network or setting up a wireless network, refer to Creating a wireless connection on page 16. ł Wired—You can access the Internet by connecting to a broadband network using the RJ-45 (network) jack. To learn about connecting using the RJ-45 jack, refer to Connecting to a wired network on page 25.
Using the Windows Connect to the Internet Wizard You can use the Windows Connect to the Internet Wizard to connect to the Internet in any of these situations: ł If you already have an account with an ISP. ł If you have a disc from an ISP. ł If you do not have an Internet account and would like to select an ISP from the list provided within the wizard. (The list of ISP providers is not available in all regions.
Wireless (disconnected) Identifies the Wireless Assistant software on the computer and indicates that all of the wireless devices are off. Wired network (connected) Indicates that one or more network drivers on your computer are installed and one or more network devices are connected to the network.
Because the wireless devices are enabled at the factory, you can use the wireless key to turn on or turn off the wireless devices simultaneously. Individual wireless devices can be controlled through Wireless Assistant software. Using Wireless Assistant software A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is disabled in Setup Utility, it must be reenabled in Setup Utility before it can be turned on or off using Wireless Assistant.
NOTE: The terms wireless router and wireless access point are often used interchangeably. ł A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions.
Step 1: Purchase high-speed Internet service If you already have high-speed Internet service (DSL, cable, or satellite), begin with . If you do not have high-speed Internet service, follow these steps: 1. Contact a local ISP to purchase high-speed Internet service and a DSL or cable modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. 2. Your ISP will give you a User ID and password to access the Internet.
Protecting your WLAN Because the WLAN standard was designed with only limited security capabilities—basically to foil casual eavesdropping rather than more powerful forms of attack—it is essential to understand that WLANs are vulnerable to well-known and well-documented security weaknesses. WLANs in public areas, or “hotspots,” like coffee shops and airports may not provide any security.
is a mobile phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voice coverage. When used with mobile network operator service, HP Mobile Broadband gives you the freedom to stay connected to the Internet, send e-mail, or connect to your corporate network whether you are on the road or outside the range of Wi-Fi hotspots.
7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated. 8. Replace the battery. NOTE: 9. HP Mobile Broadband will be disabled if the battery is not replaced. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer. Removing a SIM To remove a SIM: 1. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding the power switch.
7. Press in on the SIM (1), and then remove it from the slot (2). 8. Replace the battery. 9. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer.
Connecting to a wired network Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer. To connect to a LAN: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the network cable into a network wall jack (2).
6 Pointing devices and keyboard Using pointing devices NOTE: In addition to the TouchPad, you can also connect an external USB mouse to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Devices and Printers. Then, right-click the device representing your computer, and select Mouse settings.
Pinching Pinching allows you to zoom in or out on items such as PDFs, images, and photos. To pinch: ł Zoom in by holding two fingers together on the TouchPad, and then pull the fingers apart to increase an object's size. ł Zoom out by holding two fingers apart on the TouchPad, and then pull the fingers together to decrease an object's size. Rotating Rotating allows you rotate items such as photos and pages. To rotate, move your thumb and forefinger in a circular motion on the TouchPad.
Using the digitizer pen You can write with the pen in pen-specific programs such as Tablet PC Input Panel, in all Microsoft® Office applications, and in most other Windows programs and utilities. The information you write on the screen with the pen can be filed, searched, and shared among most Windows programs. Identifying the pen components The pen interacts with the computer whenever the tip (1) of the pen is pressed against the screen.
Review to ensure the touch screen text and illustrations are correct for Luke Using the touch screen The computer allows you to use your fingers or the digitizer pen to perform certain actions on the touch screen. NOTE: The instructions in this section are based on the preferences set at the factory. To modify settings for recognized clicks and flicks, select Start > Control Panel > Hardware and Sound > Pen and Touch. NOTE: All movements may not be supported in all programs.
Dragging Press your finger on an item on the screen and then move your finger to drag an item to a new location. You can also use this motion to slowly scroll through documents. Scrolling Scrolling is useful for moving up or down on a page or image. To scroll, place two fingers on the screen, and then drag them across the screen in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. Rotating Rotating allows you rotate items such as photos and pages.
Pinching Pinching allows you to zoom in or out on items such as PDFs, images, and photos. To pinch: ł Zoom out by holding two fingers apart on the screen, and then pull the fingers together to decrease an object's size. ł Zoom in by holding two fingers together on the screen, and then pull the fingers apart to increase an object's size. Using the touch screen Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Setting touch screen preferences To set preferences for visual feedback, select Start > Control Panel > Hardware and Sound > Pen and Touch. These preferences are specific to the touch screen and the computer. To set preferences for left-handed or right-handed users, select Start > Control Panel > Hardware and Sound > Tablet PC Settings > Other tab. These preferences are specific to the touch screen and the computer.
Icon Action Description Screen brightness down Decreases the screen brightness level incrementally when you hold down this key. Screen brightness up Increases the screen brightness level incrementally when you hold down this key. Switch screen image Switches the screen image among display devices connected to the system.
Hotkey Description Display system information. fn+esc Displays information about system hardware components and the system BIOS version number. Scroll up. fn+up arrow Scrolls the page up. Scroll down. fn+down arrow Scrolls the page down. Go home. fn+left arrow Returns the cursor to the beginning of the line where the cursor is located or returns to the beginning of the document. Go to the end. fn+right arrow Places the cursor at the end of the line or scrolls to the end of the document.
7 Multimedia Your computer includes multimedia features that allow you to listen to music, watch movies, and view pictures.
Installing multimedia software from a disc Although your computer does not have an integrated optical drive, you can easily access software, install applications, and access data in either of the following ways: ł Connect an external optical drive (select models only or purchased separately) to one of the USB ports on your computer. NOTE: For additional information on external optical drives, refer to Using external drives on page 60.
ł Gamma—Controls the contrast affecting the mid-level grays or midtones of an image. Adjusting the gamma of an image allows you to change the brightness values of the middle range of gray tones without dramatically altering the shadows and highlights. A lower gamma setting makes grays look black, and makes dark colors even darker. ł Backlight Comp—Compensates in cases where a subject with a large amount of background light would otherwise be obscured by blooming or silhouetting.
NOTE: To transmit video signals through the HDMI port, you need an HDMI cable (purchased separately). The computer can support one HDMI device connected to the HDMI port, while simultaneously supporting an image on the computer display or any other supported external display. To connect a video or audio device to the HDMI port: 1. Connect one end of the HDMI cable to the HDMI port on the computer. 2.
8 Power management Shutting down the computer CAUTION: Unsaved information will be lost when the computer is shut down. The Shut down command closes all open programs, including the operating system, and then turns off the display and computer.
CAUTION: To prevent possible audio and video degradation, loss of audio or video playback functionality, or loss of information, do not initiate Sleep or Hibernation while reading from or writing to a disc or an external media card. NOTE: You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state or in Hibernation.
Conserving power ł Select the Power saver power plan through Power Options under System and Security in Windows Control Panel. ł Turn off wireless and local area network (LAN) connections and exit modem applications when you are not using them. ł Disconnect external devices that are not plugged into an external power source, when you are not using them. ł Stop, disable, or remove any external media cards that you are not using. ł Use the screen brightness keys to adjust screen brightness as needed.
– or – Select Start > Control Panel > System and Security > Power Options, and then select a power plan from the list. Customizing power plans 1. Click the battery meter icon in the notification area and then click More power options. – or – Select Start > Control Panel > System and Security > Power Options. 2. Select a power plan, and then click Change plan settings. 3. Change the settings as needed. 4. To change additional settings, click Change advanced power settings and make your changes.
Finding battery information in Help and Support Help and Support provides the following tools and information about the battery: ł Battery Check tool to test battery performance ł Information on calibration, power management, and proper care and storage to maximize battery life ł Information on battery types, specifications, life cycles, and capacity To access battery information: Select Start > Help and Support > Learn > Power Plans: Frequently Asked Questions.
3. Pivot the battery (2) upward and remove it from the computer (3). To insert the battery: 1. Close the display and turn the computer upside down on a flat surface. 2. Align the tabs on the battery with the notches on the outer edge of the battery bay (1) and rotate the battery into the battery bay until it is seated (2). 3. The battery release latch (3) automatically locks the battery into place. Charging a battery WARNING! Do not charge the computer battery while you are onboard aircraft.
Charging may take longer if a battery is new, has been unused for 2 weeks or more, or is much warmer or cooler than room temperature. To prolong battery life and optimize the accuracy of battery charge displays, follow these recommendations: ł If you are charging a new battery, charge it fully before turning on the computer. ł Charge the battery until the battery light turns white.
Resolving a low battery level CAUTION: To reduce the risk of losing information when the computer reaches a critical battery level and has initiated Hibernation, do not restore power until the power light turns off. Resolving a low battery level when external power is available Connect one of the following devices: ł AC adapter ł Optional power adapter purchased as an accessory from HP. Resolving a low battery level when a charged battery is available 1. Turn off the computer or initiate Hibernation.
Disposing of a used battery WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. Refer to the Regulatory, Safety and Environmental Notices for proper battery disposal. Replacing the battery Computer battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors.
To connect the computer to external AC power: 1. Plug the adapter into the power connector (1) on the computer. 2. Plug the power cord into the adapter (2). 3. Plug the other end of the power cord into an AC outlet (3). Testing an AC adapter Test the AC adapter if the computer exhibits any of the following symptoms when it is connected to AC power: ł The computer will not turn on. ł The display does not turn on. ł The power light is off. To test the AC adapter: 1.
Removing a digital card CAUTION: To prevent loss of data or an unresponsive system, use the following procedure to safely remove the digital card. 1. Save your information and close all programs associated with the digital card. NOTE: 2. To stop a data transfer, click Cancel in the operating system Copying window. To remove a digital card: a. Click the Safely Remove Hardware and Eject Media icon in the notification area, at the far right of the taskbar.
To connect a USB device to the computer, connect the USB cable for the device to the USB port. You will hear a sound when the device has been detected. NOTE: The first time you connect a USB device, the "Installing device driver software" message is displayed in the notification area, at the far right of the taskbar. Removing a USB device CAUTION: To prevent loss of information or an unresponsive system, use the following procedure to safely remove the USB device.
10 Drives Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply.
To run Disk Defragmenter: 1. Select Start > All Programs > Accessories > System Tools > Disk Defragmenter. 2. Click Defragment disk. NOTE: Windows® includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing applications, running utilities, or changing Windows settings. Refer to Help and Support for more information. For additional information, access the Disk Defragmenter software Help.
To enable the notification area icon: 1. Select Start > Control Panel > Hardware and Sound > HP ProtectSmart Hard Drive Protection. NOTE: If prompted by User Account Control, click Yes. 2. On the Icon in System Tray row, click Show. 3. Click OK. Managing power with a parked hard drive If HP ProtectSmart Hard Drive Protection has parked the drive, the computer will behave in the following ways: ł The computer will not shut down.
Inserting and removing a hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding the power switch. Then shut down the computer through the operating system. To remove the hard drive: 58 1. Save your work. 2.
10. Lift the hard drive (2) out of the hard drive bay. To install a hard drive: 1. Insert the hard drive into the hard drive bay (1). 2. Pull the hard drive tab (2) to the right until the hard drive snaps into place. 3. Align the tabs (1) on the hard drive cover with the notches on the computer. 4. Close the cover (2). Inserting and removing a hard drive Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
5. Tighten the hard drive cover screws (3). Using external drives Removable external drives expand your options for storing and accessing information. USB drives include the following types: ł 1.
You may have one of the following types of drives: ł DVD±RW SuperMulti Double-Layer (DL) Drive ł Blu-ray ROM DVD±R/RW SuperMulti Double-Layer (DL) Drive Removing an optical disc when the disc tray will not open If your optical drive is a tray load drive and the disc tray does not open, follow these steps: 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2.
To share an optical drive: 62 1. From the computer with the optical drive you are sharing, select Start > Computer. 2. Right-click the optical drive you want to share, and click Properties. 3. Select the Sharing tab > Advanced Sharing. 4. Select the Share this folder check box. 5. Type a name for the optical drive in the Share name text box. 6. Click Apply, and then click OK. 7.
11 Memory modules The computer has two memory module compartments, which are located on the bottom of the computer. The memory capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
9. If you are replacing a memory module, remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 11. Align the tabs (1) on the memory module compartment cover with the notches on the computer. 12. Close the cover (2). 13. Tighten the 2 memory module compartment screws (3). 14. Replace the battery. 15.
12 Security Protecting the computer Standard security features provided by the Windows® operating system and the non-Windows Setup Utility can protect your personal settings and data from a variety of risks.
You can use the same password for a Setup Utility feature and for a Windows security feature. You can also use the same password for more than one Setup Utility feature. Use the following guidelines when setting a password in Setup Utility: ł A password can be any combination of up to 8 letters and numbers and is case sensitive. ł A password set in Setup Utility must be entered at a Setup Utility prompt. A password set in Windows must be entered at a Windows prompt.
Administrator password Your administrator password protects the configuration settings and system identification information in Setup Utility. After this password is set, you must enter it each time you access Setup Utility. Your administrator password is not interchangeable with an administrator password set in Windows, nor is it displayed as it is set, entered, changed, or deleted. Be sure that you record your password and store it in a safe place.
Managing a power-on password To set, change, or delete this password, follow these steps: 1. Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press f10. – or – Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f10. 2.
Firewall features include logging and reporting of network activity, and automatic monitoring of all incoming and outgoing traffic. Refer to the firewall user guide or contact your firewall manufacturer for more information. NOTE: Under some circumstances a firewall can block access to Internet games, interfere with printer or file sharing on a network, or block authorized e-mail attachments.
Using your registered fingerprint to log on to Windows To log on to Windows using your fingerprint, follow these steps: 72 1. Immediately after you have registered your fingerprints, restart Windows. 2. Swipe any of your registered fingers to log on to Windows. Chapter 12 Security Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
13 Backup and recovery Recovery after a system failure is as complete as your most current backup. HP recommends that you create recovery discs immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
ł Only one set of recovery discs can be created per computer. ł Number each disc before inserting it into the optical drive. ł If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open Recovery Manager, you will be prompted to continue the disc creation process. To create a set of recovery discs: 1. Select Start > All Programs > Recovery Manager > Recovery Disc Creation. 2. Follow the on-screen instructions.
Using Windows Backup and Restore To create a backup using Windows Backup and Restore, follow these steps: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to set up and create a backup.
4. Click System Restore. 5. Follow the on-screen instructions. Performing a recovery NOTE: You can recover only files that you have previously backed up. HP recommends that you use HP Recovery Manager to create a set of recovery discs (entire drive backup) as soon as you set up your computer. Recovery Manager software allows you to repair or restore the system if you experience system failure or instability.
14 Setup Utility (BIOS) Starting Setup Utility Setup Utility is a ROM-based information and customization utility that can be used even when your Windows® operating system is not working. The utility reports information about the computer and provides settings for startup, security, and other preferences. To start Setup Utility: Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
Navigating and selecting in Setup Utility Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke. ł To choose a menu or a menu item, use the arrow keys. ł To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or f5 or f6. ł To select an item, press enter. ł To close a text box or return to the menu display, press esc.
Exiting Setup Utility You can exit Setup Utility with or without saving changes. ł To exit Setup Utility and save your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes, and then press enter. ł To exit Setup Utility without saving your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display.
Select To do this Action Keys Mode Enable/disable the Action Keys. Boot Options Set the following boot options: ł POST Hot Key Delay (sec.)ʊSet the delay for the user to press hot keys in intervals of 5 seconds each (0, 5, 10, 15, 20). ł Floppy BootʊEnable/disable boot from diskette. ł Network Adapter BootʊEnable/disable boot from external Network Adapter.
To use Setup Utility for displaying BIOS information: 1. Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press f10. 2. If Setup Utility does not open with the system information displayed, use the arrow keys to select the Main menu. When the Main menu is selected, BIOS and other system information is displayed. 3.
The BIOS installation begins. 5. Complete the installation by following the instructions on the screen. NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file from your hard drive. 82 Chapter 14 Setup Utility (BIOS) Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
A Product information Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer. The computer can operate on DC power within the following specifications.
Traveling with the computer For best results, follow these traveling and shipping tips: ł Prepare the computer for traveling or shipping: Ń Back up your information. Ń Remove all discs and all external media cards, such as digital cards. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, remove the media from a drive before removing the drive from a drive bay, and before shipping, storing, or traveling with a drive.
To remove smudges and lint, frequently clean the display with a soft, damp, lint-free cloth. If the screen requires additional cleaning, use premoistened antistatic wipes or an antistatic screen cleaner. Cleaning the TouchPad and keyboard Dirt and grease on the TouchPad can cause the pointer to jump around on the screen. To avoid this, clean the TouchPad with a damp cloth, and wash your hands frequently when using the computer.
certification labels are included with your computer. You may need this information when traveling internationally. Wireless certification labels are affixed to the bottom of the computer. 86 ł SIM label (select models only)—Provides the ICCID (Integrated Circuit Card Identifier) of your SIM. This label is located inside the battery bay. ł HP Mobile Broadband Module serial number label (select models only)—Provides the serial number of your HP Mobile Broadband Module.
B Troubleshooting If you experience computer problems, perform these troubleshooting steps in the sequence provided until the problem is resolved: 1. Refer to “Quick troubleshooting,” the next section in this appendix. 2. Access Web site links and additional information about the computer through Help and Support. Click Start, and then click Help and Support. 3. Contact customer support. Refer to “Contacting customer support,” later in this appendix.
Software is functioning abnormally If the software is unresponsive or responds abnormally, follow these suggestions: ł Restart the computer by clicking Start, clicking the arrow next to Shut down, and then clicking Restart. If you cannot restart the computer using this procedure, refer to the next section, “The computer is on but is not responding.” ł Run a virus scan. For information about using the antivirus resources on the computer, refer to the antivirus software Help for more details.
To check the record functions of the computer, follow these steps: 1. Select Start > All Programs > Accessories > Sound Recorder. 2. Click Start Recording and speak into the microphone. Save the file to your desktop. 3. Open Windows Media Player or MediaSmart and play back the sound. NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise.
Cannot connect to a preferred network Windows can automatically repair a corrupted WLAN connection: ł If there is a network icon in the notification area, at the far right of the taskbar, right-click the icon, and then click Diagnose and repair from the menu. Windows resets your network device and attempts to reconnect to one of the preferred networks. ł If there is no network icon in the notification area, follow these steps: 1.
4. Click the Security tab and enter the correct wireless encryption data into the Network security key box. 5. Click OK to save these settings. WLAN connection is very weak If the connection is very weak, or if your computer cannot make a connection to a WLAN, minimize interference from other devices, as follows: ł Move your computer closer to the wireless router or access point.
Index A AC adapter testing 51 AC power, connecting 50 action key mode 80 action keys adjusting volume 33 audio CD, DVD, or BD controls 33 decrease screen brightness 33 Help and Support 32 identifying 10 increase screen brightness 33 muting speaker sound 33 switching screen image 33 using 32 volume 37 wireless 17, 33 administrator password creating 68 entering 68 managing 68 airport security devices 55 antivirus software, using 69 audio devices, connecting external 38 audio functions, checking 88 audio-in (m
hard 58, 59, 60 optical 60 DVD drive 60 E encryption 21 End hotkey 34 entering a power-on password 69 entering an administrator password 68 esc key, identifying 10 external audio devices, connecting 38 external drive 60 external monitor port 40 external optical drive 37 external WWAN antenna, identifying 10 F f11 76 fan always on 79 fingerprint reader identifying 11 fingerprints, registering 71 firewall software 21, 69 flicks changing assignments 32 creating assignments 32 fn key, identifying 10, 33 full sy
media controls, keys 33 MediaSmart using 36 MediaSmart software 36 memory module inserting 64 removing 64 memory module compartment cover removing 63 replacing 65 memory module compartment, identifying 14 memory test 80 microphone (audio-in) jack, identifying 12 Microsoft Certificate of Authenticity label 85 minimizing interference 91 monitor, connecting 40 mouse, external setting preferences 26 multimedia software installing 37 using 36 mute key identifying 33 using 37 mute light, identifying 9 N network c
MediaSmart 36 TouchSmart 36 using 36 Wireless Assistant 18 solid-state drive (SSD) 73, 76 speakers, identifying 13 storing battery 49 supported discs 73 switch power 11 System Configuration menu 79 system failure or instability 73 system information hotkey 34 system information, displaying 78, 79 system recovery 76 system restore points 73, 75 T temperature 49 touch screen performing screen actions 29 preferences 32 using 29 TouchPad buttons 8 cleaning 85 gestures 26 identifying 8 using 26 TouchPad gestures
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
