User’s Guide Learn how to use your Fujitsu MH380 notebook
Copyright and Trademark Information Fujitsu America, Inc. has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited.
WARNING HANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Fujitsu America, Inc. Address: 1250 E. Arques Avenue Sunnyvale, CA 94085 Telephone: (408) 746-6000 Declares that product: Base Model Configuration: Fujitsu MH380 notebook Complies with Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a minimum current of 2.1 A (40 W).
Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly.
Contents Preface About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Chapter 1 Getting to Know Your Notebook Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Opening the Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Adjusting Display Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Power/Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Hibernation (Save-to-Disk) Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4 Troubleshooting Your Notebook Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Identifying the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Troubleshooting Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Power On Self Test Messages . . . . . .
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Bluetooth Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 What is Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Where to Find Information About Bluetooth . . . . . . . . . . . . . . . . . . . . . . . 123 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface About This Guide The MH380 notebook from Fujitsu is a small yet powerful computer, perfect for networking. It is powered by an Intel Atom® processor and integrated Intel® NM10 Express chipset. The notebook has a built-in 10.1” wide SVGA color display with LED backlight. This manual explains how to operate your MH380 notebook’s hardware and built-in system software. Your MH380 notebook comes with Windows® 7 Starter Edition pre-installed.
THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION CAREFULLY. THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR NOTEBOOK, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
Fujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com. YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS. Limited Warranty Your MH380 notebook is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your notebook for the Limited Warranty period and terms and conditions.
Chapter 1 Getting to Know Your Notebook Overview This section describes the components of your Fujitsu MH380 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers. Figure 1.
Locating the Controls and Connectors Connectors and peripheral interfaces on the MH380 notebook allow you to connect a variety of devices. Specific locations are illustrated in Figures 2 through 6. The table below provides a short description of each icon on the MH380 notebook. Each of the icons is either molded into or printed on the notebook chassis. Connection Notebook Icon Purpose DC in connector Connect an external power source such as the AC adapter or auto/airline adapter.
Connection Notebook Icon Purpose Suspend/ Resume button The Suspend/Resume button allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on the system when it has been shut down from Windows. Local Area Network (LAN) The LAN (RJ-45) jack is used to connect the internal 10/100 Base-T/Tx Ethernet to a Local Area Network (LAN) in your office or home, or broadband devices such as a cable modem, DSL, or satellite Internet.
1.3 Megapixel Web Camera Display Panel Status Indicator Panel Touchpad Pointing Device Built-in Microphone Power/Suspend/ Resume Button Keyboard Status Indicator Panel Scroll wheel Figure 2.
Keyboard and Display Components The following is a brief description of your notebook’s keyboard and display features. Web Camera The 1.3 megapixel web camera lets you take pictures of yourself to send over the internet. For information on using the camera, see the documentation associated with the CyberLink YouCam application. Display Panel The display panel is a color LCD panel with back lighting for the display of text and graphics.
Stereo Speaker Microphone Jack Headphone Jack Stereo Speaker Secure Digital Card Slot Figure 3. MH380 notebook front components Front Components Stereo Speakers The speakers allows you to listen to stereo sound from your system. Headphone Jack The headphone jack allows you to connect stereo headphones or powered external speakers. See “Headphone Jack” on page 63. Microphone Jack The microphone jack allows you to connect an external mono microphone. See “Microphone Jack” on page 62.
Anti-Theft Lock Slot Air Vents USB 2.0 Ports Figure 4. MH380 notebook left-side panel Left-Side Panel Components The following is a brief description of your notebook’s left-side components. Anti-theft Lock Slot The anti-theft lock slot allows you to attach a optional physical lock-down device. Air Vents The air vents allow proper air circulation to ensure that the system does not overheat.
USB 2.0 Port Air Vents LAN (RJ-45) Jack External Video Port DC Power Jack Figure 5. MH380 notebook right-side panel Right-Side Panel Components The following is a brief description of your notebook’s right-side components. USB 2.0 Ports The three USB 2.0 ports (two on the left side, one on the right side) allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480 Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12 Mbps.
LAN (RJ-45) Port The internal LAN (RJ-45) port is used for an internal 10/100 Base-Tx Ethernet. See “Internal LAN (RJ45) jack” on page 62. External Video Port The external video port allows you to connect an external monitor or LCD projector. See “External Video Port” on page 63. DC Power Jack The DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your system and charge the internal Lithium ion Battery.
Memory Upgrade Compartment Battery Latch Battery Latch Lithium ion Battery Figure 6. MH380 notebook bottom panel Bottom Components The following is a brief description of your notebook’s bottom panel components. Battery Latches The battery latches are used to secure the Lithium ion battery in the battery bay.
Lithium ion Battery The battery compartment contains the Lithium ion battery. The battery should be removed when the computer is stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. See “Lithium ion Battery” on page 51. Memory Upgrade Compartment Your notebook comes with high speed DDR2 Synchronous Dynamic RAM (SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your system, hence improving overall performance.
Hard Drive Access Power Indicator Battery Charge/ DC In Battery Remaining NumLock ScrLock CapsLock Wireless Device Indicator NEED SYSTEM GRAPHIC Figure 7. Status Indicator Panel Status Indicator Panel The status indicators display symbols that correspond to specific components of your notebook. (Figure 7) The symbols show how each of those components is operating. Note that there are two locations that contain status indicators: above the keyboard and on the front edge of the notebook.
Wireless Device Emission Indicator The Wireless Device Emission indicator appears when the Wireless LAN or Bluetooth are emitting. Power Indicator The Power indicator symbol located on the power button shows whether your system is operational. When it is solid blue, it means that there is power to your computer and that it is ready for use.
• Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged. • A shorted battery is damaged and must be replaced. Battery Charge/DC-In Indicator Depending upon whether you have an AC adapter connected or not, the battery indicator will appear in a variety of colors and states. AC Adapter connected... Solid blue Charge complete Solid orange Charging in process Purple, blinking Battery malfunction No AC Adapter connected...
Hard Drive Access Indicator The Hard Drive Access indicator lights blue when your internal hard drive is being accessed. Number Lock Indicator The NumLk indicator glows green when the integral keyboard is set in ten-key numeric keypad mode. Caps Lock Indicator The CapsLock indicator glows green when your keyboard is set to type in all capital letters. Scroll Lock Indicator The ScrLk indicator glows green when your scroll lock is active.
Display Cover Figure 2. Opening the Display Panel Display Panel Your Fujitsu notebook contains a display panel that is backlit for easier viewing in bright environments. Opening the Display Panel Lift the display backwards, being careful not to touch the screen with your fingers, until it is at a comfortable viewing angle.
Adjusting Display Panel Brightness Once you have turned on your Tablet PC, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness: keyboard and power management utility. Using Keyboard to Adjust Brightness Adjusting the brightness using the keyboard changes the system setting (i.e., the settings you make via the function keys automatically changes the brightness settings in the system’s Pen and Tablet Settings).
Keyboard Function Keys Backspace Fn Key Start Key Numeric Keypad (surrounded by heavy line) Application Key Cursor Keys Figure 3. Keyboard Using the Keyboard Your MH380 notebook has an integral 82-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys.
• Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. • Function keys: The keys labeled [F1] through [F11/F12], are used to produce special actions that vary depending on what program is running. They are also used in conjunction with the [Fn] key to perform certain tasks, as detailed below under “Function Keys”.
Function Keys Your notebook has 11 function keys, F1 through F11/F12. The functions assigned to these keys differ for each application. • • • • • • • • [Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off. [Fn +F4]: Pressing [F4] while holding [Fn] allows you to toggle the touchpad on and off. [Fn +F5]: Pressing [F5] while holding [Fn] allows you to toggle the wireless devices on and off.
Touchpad Pointing Device/Scroll Wheel Cursor Control Scroll Wheel Left Button Right Button Status Indicator Panel (reference only) Figure 4. Touchpad pointing device The Touchpad pointing device comes built into your Fujitsu notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left button and a right button. The cursor control works the same way a mouse does, and moves the cursor around the display.
AN EXTERNAL MOUSE CAN BE CONNECTED TO THE USB PORTS ON YOUR NOTEBOOK AND USED HOWEVER, IF YOU BOOT THE SYSTEM WITH AN EXTERNAL MOUSE CONNECTED THE TOUCHPAD WILL BE DISABLED OR ENABLED DEPENDING ON THE SPECIFICATIONS IN YOUR BIOS SETTINGS. See “BIOS Setup Utility” on page 43. SIMULTANEOUSLY WITH THE TOUCHPAD. Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it.
Double-Clicking Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice. Figure 7. Double-clicking with button Figure 8.
Touchpad Control Adjustment The Windows Control Panel allows you to customize your touchpad with selections made from within the Mouse Properties dialog box. To access the Mouse Properties dialog, go to the Control Panel, then select Mouse from the menu. Using the Scroll Wheel The scroll wheel is located to the right of the touchpad (Figure 4).
Volume Control Your Fujitsu notebook has multiple volume controls which interact with each other. ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.
Chapter 2 Getting Started with Your Notebook DC Power Jack DC Output Cable AC Adapter AC Cable Figure 10.
Power Sources Your Fujitsu notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter. Connecting the Power Adapters The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter 1 Plug the DC output cable into the DC power jack of your notebook. 2 Plug the AC adapter into an AC electrical outlet.
Starting Your MH380 Notebook Power On Power/Suspend/Resume Button The Power/Suspend/Resume button is used to turn on your notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your notebook. WHEN YOU TURN ON YOUR NOTEBOOK, BE SURE YOU HAVE A POWER SOURCE. THIS MEANS THAT AT LEAST ONE BATTERY IS INSTALLED AND CHARGED, OR THAT THE AC OR AUTO/AIRLINE ADAPTER IS CONNECTED AND HAS POWER.
NEVER TURN OFF YOUR NOTEBOOK DURING THE POWER ON SELF TEST (POST) OR IT WILL CAUSE AN See “Power On Self Test Messages” on page 74. ERROR MESSAGE TO BE DISPLAYED WHEN YOU TURN YOUR NOTEBOOK ON THE NEXT TIME. Boot Sequence The procedure for starting-up your notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This information is in the BIOS program.
Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following: 1 2 Turn on or restart your notebook. 3 Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings. To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.
Starting Windows the First Time Registering with Microsoft In order to ensure that you receive the most benefits from the Windows operating system, it should be registered the first time you use it. After you receive the Windows Welcome screen, you will be prompted to enter registration information in the following order. First of all, you will need to read and accept the End User License Agreements (EULAs). After accepting the EULAs, you will be asked if you want to enable the Automatic Updates feature.
Registering your notebook with Fujitsu You can register your notebook by going to our website at: us.fujitsu.com/computers. You will need to be set up with an Internet Service Provider (ISP) to register online. ClickMe! Installing ClickMe! BEFORE INSTALLING THE CLICKME! UTILITY, BE SURE THE WIRELESS LAN DEVICE IS ENABLED BY PRESSING THE [FN] + [F5] KEY COMBINATION. The first time you boot up your system, you will see an icon called Click Me! in the Start menu.
Power Management Your notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.
• Timing out from lack of activity. • Allowing the battery to reach the Dead Battery Warning condition. Your notebook’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Standby mode, your notebook will return to the point where it left off.
Windows Power Management The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to create a power plan, turn on password protection, or determine what the power button does. Restarting the System If your system is on and you need to restart it, be sure that you use the following procedure. 1 2 Click the [Start] button, and then click the small arrow to the right of the [Shut down] button.
ENERGY STAR® Compliance Your Fujitsu system is an ENERGY STAR® qualified mobile PC. By choosing a computer with the latest energy-saving technology, you’re helping to preserve our environment for future generations. ENERGY STAR is a joint program of the U.S. Environmental Protection Agency, U.S. Department of Energy, Natural Resources Canada, and other governments around the world helping us save money while protecting the environment through energy efficient products and practices.
Chapter 3 User-Installable Features Lithium ion Battery Your notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards. The Lithium ion battery operating time may become shorter if it is used under the following conditions: • When used at temperatures that exceed a low of 5°C or a high of 35°C.
• ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES, POWER MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES. OPTICAL DRIVE OR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE. THE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR BATTERY IS RUNNING LOW QUICKLY, YOU SHOULD REPLACE IT WITH A NEW ONE. • UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING THEM IN THE TRASH.
USING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENT CHARGING COMPLETELY. Low Battery State When the battery is running low, the Battery Level indicator will glow red. If you do not respond to the low battery alarm, the batteries will continue to discharge until they are too low to operate. Your notebook will then go into Standby mode to try and protect your data for as long as possible.
Cold-swapping Batteries 1 2 3 4 Have a charged battery ready to install. 5 6 7 Slide the right battery latch (labeled “2”) to the right. 8 Plug in the AC adapter and turn the power on. Shut down your system and disconnect the AC adapter. Close the display and turn the system over. Holding the system upside down with the battery towards the back, slide the left battery release latch (labeled “1 HOLD”) to the left and hold it.
IF THE LITHIUM ION BATTERY CONNECTOR IS NOT FULLY SEATED, YOU MAY NOT BE ABLE TO USE YOUR NOTEBOOK OR CHARGE YOUR BATTERY. NEW GRAPHIC Figure 11.
Memory Upgrade Module Your Fujitsu MH380 notebook comes with 1GB of high speed Double Data Rate Synchronous Dynamic RAM 2 (DDR2 SDRAM), 667 MHz factory installed. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com. • DO NOT REMOVE ANY SCREWS FROM THE MEMORY UPGRADE MODULE COMPARTMENT EXCEPT THE ONES SPECIFICALLY SHOWN IN THE DIRECTIONS FOR INSTALLING AND REMOVING THE MEMORY UPGRADE MODULE.
8 Install a new module as outlined in the procedure below. 9 Replace the cover. 10 Replace the screws. Figure 12. Opening the Memory Compartment 57 - Memory Upgrade Module Figure 13.
Installing a Memory Upgrade Module 1 Remove the new memory upgrade module from the static guarded sleeve. 2 Align the memory upgrade module with the component side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. (Figure 14) 3 Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is properly in place.
Checking the Memory Capacity Once you have changed the system memory capacity by replacing the installed module with a larger one, be sure to check that your notebook has recognized the change. Check the memory capacity by clicking [Start] > Control Panel, then clicking the System icon.
SD Card SD Card Slot Figure 15. Installing an SD Card Secure Digital Cards Your notebook supports Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data. Secure Digital Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. These cards transfer data quickly, with low battery consumption.
Inserting SD Cards Secure Digital Cards are inserted in the SD Card slot (Figure 15). To insert a card, follow these steps: • INSERTING OR REMOVING AN SD CARD DURING YOUR NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR NOTEBOOK. • DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR NOTEBOOK, OR BOTH. 1 See your card manual for instructions on the insertion of your card.
Device Ports Your MH380 notebook comes equipped with multiple device ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc. Internal LAN (RJ-45) jack The internal LAN (RJ-45) jack is used for an internal 10/100 BaseTx Ethernet connection. You will need to configure your notebook to work with your particular network. (Please refer to your network administrator for information on your network configuration.
Headphone Jack The headphone jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: (See Figure 5 on page 22 for location) 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. IF YOU PLUG HEADPHONES INTO THE HEADPHONE JACK, THE BUILT-IN STEREO SPEAKERS WILL BE DISABLED.
Chapter 4 Troubleshooting Your Notebook Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
• IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE. • DO NOT RETURN A FAILED NOTEBOOK TO YOUR SUPPLIER UNTIL YOU HAVE TALKED TO A SUPPORT REPRESENTATIVE. 7 If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) Web site: http://www.computers.us.fujitsu.com/support.
Specific Problems Using the Troubleshooting Table When you have problems with your notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.
Problem Possible Cause Possible Solutions The volume is turned too low. Adjust the volume control on your notebook and operating system. Use the [Fn+F9] key combination on your keyboard to increase the volume of your notebook. The software volume control is set too low. Manually adjusting the volume (i.e., keyboard "hot keys") should dynamically adjust the volume of the operating system (see above). If that doesn’t work, adjust the sound volume control settings in your software or application.
Problem Possible Cause Possible Solutions You have installed an external keyboard or mouse, and it does not seem to work. Your external device is not properly installed. Re-install your device. See “Device Ports” on page 62. Your operating system (OS) is not set up with correct software driver for that device. Check your device and operating system documentation and activate the proper driver. You have connected an external keyboard or a mouse and it seems to be locking up the system.
Problem Possible Cause Possible Solutions The installed battery is completely discharged or there is no Power adapter (AC or Auto/Airline) installed. Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 26. Install a charged battery or a Power adapter. The battery is installed but is faulty. Use the Status Indicator panel to verify the presence and condition of the battery. See “Status Indicator Panel” on page 26.
Problem Possible Cause Possible Solutions Your notebook turns off all by itself. (continued) You are operating on battery power and ignored a low battery alarm until the battery was at the dead battery state and the system has entered Dead Battery Suspend mode. Install a power adapter, then push the Power/Suspend/Resume button. See “Power Sources” on page 41. You have a battery failure. Verify the condition of the battery using the Status Indicator panel.
Problem Possible Cause Possible Solutions The battery seems to discharge too quickly. (continued) The brightness is turned all the way up. Turn down the brightness adjustment. The higher the brightness the more power your display uses. Battery has been exposed to high temperatures. Replace the battery. The battery is too hot or too cold. Restore the notebook to normal operating temperature. Charging icon on the Status Indicator panel will flash when battery is outside of operating range.
Problem Possible Cause Possible Solutions Your notebook appears to change setup parameters when you start it. The BIOS CMOS hold-up battery has failed. Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years. An external monitor is plugged in, and the system is set for an external monitor only. Pressing [F10] while holding down [Fn] allows you to change where to send your display video.
Problem Possible Cause Possible Solutions The display goes blank by itself after you have been using it. (continued) Power timeouts are set for very short intervals and you failed to notice the display come on and go off again. Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout) The display has bright or dark spots.
Power On Self Test Messages The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.
*Keyboard error Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative. Non-system disk or disk error Replace the disk and then press any key to continue. NTLDR is missing Press any key to restart.
PXE-E78: Could not locate boot server Contact your support representative for more information. PXE-E89: Could not download boot image Contact your support representative for more information. *Real time clock error Real-time clock fails BIOS test. May require board repair. Contact your support representative. Remove disks or other media Remove disks or other media, then press any key to restart. *Stuck key BIOS discovered a stuck key.
Restoring Your System Image and Software It is very important that you create DVD copies of your Factory Image and Bootable Disc (along with other applicable media such as Drivers and Applications and Restore media and application discs) before beginning to use your system.
Enable Automatic Update Notifications Automatically searches for new updates on a regular basis (approximately every 3 days). Show update history Brings up a screen that displays a history of updates that have been made via the FDU. About Fujitsu Driver Update Displays the FDU version number and copyright information. Fujitsu Driver Update Readme Displays the FDU readme.
Chapter 5 Care and Maintenance Caring for your MH380 Notebook If you use your Fujitsu notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. • IN THE EVENT YOU DROP YOUR NOTEBOOK OR DAMAGE THE HOUSING IN ANY WAY, IMMEDIATELY TURN OFF POWER AND DISCONNECT THE POWER PLUG. FAILURE TO DO SO COULD RESULT IN A SHORT CIRCUIT, SMOKE, AND/OR FIRE.
• • • • • Your notebook is a durable but sensitive electronic device. Treat it with respect and care. Make a habit of transporting it in a suitable carrying case. Do not attempt to service the computer yourself. Always follow installation instructions closely. Keep it away from food and beverages. To protect your notebook from damage and to optimize system performance, be sure to keep all air vents unobstructed, clean, and clear of debris.
Cleaning your notebook • Always disconnect the power plug. (Pull the plug, not the cord.) • Clean your notebook with a damp, /lint-free cloth. Do not use abrasives or solvents. • Use a soft cloth to remove dust from the screen. Never use glass cleaners. • Always shut down the computer, unplug the power adapter, and remove the battery when cleaning or disinfecting the computer exterior, keyboard or LCD display.
Disinfecting notebook computers Wipe the surface with a soft cloth wipe and a 50% ethanol solution or use another ethanol-based germicide which has been registered as a hospital disinfectant by the EPA. • USE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE LCD AND/OR DAMAGE TO THE COMPUTER. ALWAYS REFER TO THE CLEANER MANUFACTURER'S GUIDELINES AND MATERIAL SAFETY DATA SHEETS FOR PROPER HANDLING AND USE OF THE PRODUCTS.
Traveling with your notebook • Do not transport your notebook while it is turned on. • It is recommended that you carry your notebook with you while traveling, rather than checking it in as baggage. • Always bring your System Recovery CD that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any problems. • Never put your notebook through a metal detector. Have your notebook hand-inspected by security personnel.
Batteries Caring for your Batteries • Always handle batteries carefully. • Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire. • Do not drop, puncture, disassemble, mutilate or incinerate the battery. • Recharge batteries only as described in this manual and only in ventilated areas.
Media Care Caring for your Media (optional) Media discs (DVD/CD/CD-R) are precision devices and will function reliably if given reasonable care. • • • • • • • • Always store your media disc in its case when it is not in use. Always handle discs by the edges and avoid touching the surface. Avoid storing any media discs in extreme temperatures. Do not bend media discs or set heavy objects on them. Do not spill liquids on media discs. Do not scratch or get dust on media discs.
Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu MH380 notebook. Specifications of particular configurations will vary. Configuration Label The configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook. Following is an example configuration label.
Microprocessor Intel® Atom™ N450 Processor Chipset • Mobile Intel NM10 Express • I/O Controller Hub 7 Mobile (ICH7M) Memory System Memory • DDR2-667 MHz SDRAM memory module. • One DIMM slot; upgradeable. Cache Memory 512 KB L2 cache on-die Video Built-in color flat-panel TFT active matrix LED backlight display with simultaneous display capability. Video Color and Resolution 10.
Audio • Realtek codec ALC269 with High Definition (HD) audio. • Headphones: Stereo headphone jack, 3.5 mm, 1 Vrms or less, minimum impedance 32 Ohms • Microphone: Stereo microphone jack, 3.5 mm, 100 mVp-p or less, minimum impedance 10K Ohms • Two built-in stereo speakers • One built-in digital mono microphone Mass Storage Device Options Hard Drive 160 GB, Serial ATA, 150 Mbps data buffer, 5400 rpm, 2.
Device Ports On the notebook: • • • • • • • Secure Digital (SD) Card slot One 15-pin D-SUB connector for VGA external monitor (see Display specifications) Three USB 2.0 (Universal Serial Bus) connectors for input/output devices One DC In connector One LAN (RJ-45) connector One stereo headphone jack One stereo microphone/line-in jack Keyboard Built-in keyboard with all functions of 101 key PS/2 compatible keyboards.
Dimensions and Weight Overall Dimensions Approximately 10.16"(w) x 7.4"(d) x 1.26” / 1.69” (h) (258 mm x 188 mm x 32 mm / 42.9 mm) Weight Approximately 2.93 lb. (1.33 Kg) with battery Environmental Requirements Temperature Operating: 41° to 95° F (5° to 35° C). Non-operating: 5° to 140° F (–15° to 60° C) Humidity Operating: 20% to 85%, relative, non-condensing.
Included Software Depending on your operating system, your notebook comes with software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. The following list indicates the software included with your system.
Adobe Reader The Adobe Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms. Norton Internet Security Your system is preinstalled with a free 60-day trial version of Symantec’s Norton Internet Security™. Internet Security is a suite of tools designed to protect your notebook from viruses, hackers, spyware, and spam. It assists in the protection of data currently on your hard disk from destruction or contamination.
Fujitsu Driver Update Utility The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See “Automatically Downloading Driver Updates” on page 77. Microsoft Works with Office 2007 Student and Home Trial Edition Microsoft Works 9.
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your notebook. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
ADSL Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines. AGP Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your notebook. BIOS Basic Input-Output System.
Bus An electrical circuit which passes data between the CPU and the sub-assemblies inside your notebook. Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster. CD-ROM Compact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head.
DC Direct current. A voltage or current that does not fluctuate periodically with time. Default Value A pre-programmed value to be used if you fail to set your own. DHCP Dynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required for the communication, such as IP address. The sender of IP address is called a DHCP server, and the receiver is called a DHCP client. DIMM Dual-in-line memory module. Disk A spinning platter of magnetic data storage media.
DMI Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals. DNS Domain Name System. A function to control the association between the IP address and the name assigned to the computer. If you do not know the IP address but if you know the computer name, you can still communicate to that computer.
ESD Electrostatic Discharge. The sudden discharge of electricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day. FCC Federal Communication Commission. GB Gigabyte. One billion bytes. Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. I/O Input/Output. Data entering and leaving your notebook in electronic form.
IEEE802.11g Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the 2.4 GHz ISM band. IEEE802.11n Wireless LAN standard that supports a maximum data rate of 200 Mbps. 802.11n devices operate in the 2.4 GHz ISM band. Infrastructure A name of a wireless LAN configuration. This type of communication uses an access point. Another type of communication is called Ad Hoc. IP Address An identifier for a computer or device on a TCP/IP network.
IRQ Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. KB Kilobyte. One thousand bytes. LAN Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves. LCD Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.
Megahertz 1,000,000 cycles per second. Memory A repository for data and applications which is readily accessible to your notebook’s CPU. MHz Megahertz. MIDI Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers. Modem A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.
Network name (SSID: Service Set Identifier ) When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key. Open system authentication Null authentication method specified in the 802.
POST Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. PPPoE Point to Point Protocol over Ethernet.
Reset The act of reloading the operating system. A reset erases all information stored in RAM. Restart See Reset. Resume To proceed after interruption. In your notebook this refers to returning to active operation after having been in one of the suspension states. SDRAM Synchronous Dynamic Random Access Memory. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.
Standby To make inoperative for a period of time. Your notebook uses various suspension states to reduce power consumption and prolong the charge of your battery. Status Indicator A display which reports the condition of some portion of your hardware. On your notebook this is an LCD screen just above the keyboard. Stereo (audio) A system using two channels to process sound from two different sources. Subnet mask TCP-IP network is controlled by being divided into multiple smaller networks (subnets).
TFT Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually. UL Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices. USB Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer. VRAM Video Random Access Memory.
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.
Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
Before Using the Wireless LAN This manual describes the procedures required to properly set up and configure the integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure its correct operation. Keep this manual in a safe place for future reference. Wireless LAN Device Covered by this Document The following wireless LAN device is contained in this system: • Integrated Atheros AR5B95 (802.
Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).
How to Handle This Device The WLAN device is a device that omes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. • The Wireless LAN device supports IEEE802.11b, IEEE802.11g, and IEEE802.11n. • The WLAN devices operate in the 2.4 GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.
Disconnection Using the Icon in the Taskbar Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected. 1 2 Right-click the WLAN icon in the taskbar at the bottom right of your screen. Choose Disconnect from a network.
Configuring the Wireless LAN The WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Configuring the WLAN using Windows 7 Procedure 1 2 3 4 5 6 7 Click the [Start] button, then select Control Panel.
Troubleshooting the WLAN Troubleshooting Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table.
Problem Unavailable network connection (continued) Possible Cause Possible Solution RF interference from Access Points or other wireless networks The use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device. Wireless network authentication has failed Re-check your Network Authentication, Encryption, and Security settings.
WLAN Specifications Specifications Item Specification Type of network The integrated Atheros AR5B95 802.11bgn Wireless LAN device conforms to 802.11b, 802.11g, and 802.11n Wi-Fi based*. Transfer rate (Automatic switching) 54 Mbps maximum data rate Active frequency • • Typical operating distances** • • • 802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps 802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps 802.11n: Estimated double the operating distance of 802.11g and 802.
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed. ** The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources. *** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/ 104 bits after subtracting the fixed length of 24 bits.
Using the Bluetooth Device The Bluetooth module (Broadcom BCM92070MD_REF) is integrated into your Fujitsu mobile computer. What is Bluetooth Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located on the front edge of the right palm rest and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.
Index A BIOS guide 44 setup utility 43 Bluetooth 123 Boot Sequence 43 Booting the System 44 Built-in Speakers 67 About This Guide 1, 12 AC adapter 41 plug adapters 83 Air Vents 25 Anti-theft Lock Slot 24 Auto/Airline Adapter 41 C CapsLock Indicator 29 Click Me! 46 Clicking 36 Configuration Label 86 Contact Information 13 Controls and Connectors 16 Conventions Used in the Guide 12 Cursor 35 Cursor Keys 33 B Battery 51 alarm 53 care 84 Charge/DC-In Indicator 28 cold-swapping 54 conserving power 47 dead 70
E K Error Messages 74 External Monitor Port 23, 63 Keyboard 19, 32 cursor keys 33 numeric keypad 32 problems 67 windows keys 33 F FDU 46, 77, 93 Fujitsu Contact Information 13 Fujitsu Driver Update utility 46, 77, 93 Fujitsu Shopping Online 14 Function Key F10 34 F3 34 F5 34 F6 34 F7 34 F8 34 F9 34 L LAN (RJ-45) Jack 23 Lithium ion Battery Bay 25 Local Area Network (LAN) 17 M Memory capacity 59 checking capacity 59 compartment 25, 58 installing 57 problems 68 removing 59 upgrade module 56 Microphone J
failure 69 indicator 27 management 47 off 49 on 42 problems 71 sources 41 Power Management 47 Power On Self Test 42, 74 Power/Suspend/Resume Button 47 Pre-Installed Software 91 Adobe Acrobat Reader 92 Google Toolbar 92 manuals 91 Audio 88 Chipset 87 Device Ports 89 Dimensions and Weight 90 Environmental Requirements 90 Keyboard 89 mass storage device options 88 Memory 87 Microprocessor 87 Power 89 Video 87 status indicators 19, 26 Suspend/Resume Button 17, 19 R Touchpad 35 buttons 35 controls 38 Troubles
Wireless LAN before using the wireless LAN 113 configuring 113 connection to the network 118 deactivating/disconnecting 116 modes 114 Specifications 121 Troubleshooting 119 128
