User's Manual

ManualsBrandsQolsys ManualsElectronicswireless door/window sensor to be used in the Qolsys IQ home security system

IQ DOOR/WINDOW- INSTALLATION MANUAL

QOLSYS CONFIDENTIAL AND PROPRIETARY PAGE 1 OF 6

The Qolsys IQ Door/Window is a sleek, high-

performance wireless sensor that detects opening

and closing of doors, windows and anything else

which opens and closes (drawers, cabinets, etc). It

works seamlessly with the Qolsys IQPanel.

1 Door/Window Sensor

1 Magnet

6 screws

1 large strip of double sided adhesive

1 small strip of double sided adhesive

PRODUCT FEATURES

PARTS INCLUDED

IQ DOOR/WINDOW

Wireless signal range: 600ft (200M),open air.

Code outputs: tamper, tamper restore, alarm (primary open),

alarm restore (primary close), external alarm (secondary

wired open), external restore (secondary wired closed), low

battery.

Transmitter frequency : 319.5MHZ

Unique code ID

Supervisory keep-alive interval: 70 minutes.

RF output power!91.1dBuV +/- 5% at 3m

TECHNICAL SPECIFICATIONS

•Low profile

•Supports one or two doors, windows, etc.

•Primary wireless magnet contact and secondary wired

contact

•Internal or external reed switch

•Easy, wire-free installation

•Secondary (optional) sensor (external wired Door/Window

sensor)

•Advanced circuit technology resulting in ultra-low power

consumption

•Easy to install Batteries

•Over 5 years of battery life

•Tamper Detection

•Supervisory health messaging

•Sensor Open and Close detection

Summary of content (6 pages)

PAGE 1
IQ DOOR/WINDOW- INSTALLATION MANUAL IQ DOOR/WINDOW The Qolsys IQ Door/Window is a sleek, highperformance wireless sensor that detects opening and closing of doors, windows and anything else which opens and closes (drawers, cabinets, etc). It works seamlessly with the Qolsys IQPanel. TECHNICAL SPECIFICATIONS Wireless signal range: 600ft (200M),open air.
PAGE 2
IQ DOOR/WINDOW- INSTALLATION MANUAL GUIDELINES 6 •Mount the sensor on the door frame and the magnet on the door. If the sensor is used on double doors, mount the sensor on the least-‐used door and the magnet on the most-‐used door. PLACEMENT AND SPACING Be sure to align the triangle guides on the sensor and magnet as shown. This will enable the proper contact between the sensor and magnet.
PAGE 3
IQ DOOR/WINDOW- INSTALLATION MANUAL MOUNTING WITH PROVIDED ADHESIVE •Remove backing on one side of the large double-‐sided tape and sJck the exposed side on the back of the sensor as shown.
PAGE 4
IQ DOOR/WINDOW- INSTALLATION MANUAL PROGRAMMING THE IQ DOOR/WINDOW The following steps describe general guidelines for programming (learning) the sensor into the IQ Panel. Refer to the IQ Panel's installation instructions for complete programming details. 1 From the home screen of the IQ panel, touch the “Settings” icon 2 Enter the installer passcode.
PAGE 5
IQ DOOR/WINDOW- INSTALLATION MANUAL BATTERY REPLACEMENT Push to remove sensor cover To replace batteries: •Push tab on side of sensor and lift off cover. •Place fingernail or small screwdriver under the battery and gently lift up. The battery should release easily. Remove old battery. Replace with a new battery by putting one end under the golden battery retention clip. Gently push toward the opposite side until the the battery snaps into place under the black plastic.
PAGE 6
IQ DOOR/WINDOW- INSTALLATION MANUAL IMPORTANT INFORMATION 15.21 § 15.21 Information to user. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.