User's Manual

17
DISCLAIMER AND OPERATION GUIDLINES
Q-538
About Q358 Doorbell
10
1.Solar panel
2.Speaker
3.Bell button
4.Talking button
5.Pairing button
6.Power
7.Volume
8.Bell-ring
9.Channel
10.Charger port
11.Charger dock
Picture 1
3
Name Function
Press the outdoor unit bell to call the
indoor unit, the indoor unit will ring
("ding-dong" or music) to remind
visitors coming.
Re-pairing
key
Volume
Bell
Doorbell
music
Press it to choose your favorite ringings.
Channel
3 channels for choice. A, B,C.
Please check and make sure that indoor
and outdoor units' channels are the same.
Please check its corresponding
frequencies and CDCS CODES in Table 2.
Power
TALK
button
After received a voice from the indoor
unit, press and hold the talk button to
speak. (Speaking time, within 60s)
Led
indicators
Blue light indicate pairing status,
Red light indicates the power.
Press and hold for 3 seconds, the
mechine enters into pairing mode.
OUTDOOR
4
3.2. Installation
3.2.1. Indoor Unit installation
Already assembled, ready for charging and using. Please
put it in the charging dock for charging while not use to
avoid missing visitors caused by out of power.
3.1. Included parts
5. Screws *6
6.
Screwdriver
*1
7.
User manual
*1
8.
USB Cable
*1
9. Battery *2
1. Outdoor machine *1
2. Solar panel *1
3.
Indoor machine
*1
4.
Chagrer dock
*1
Picture 2
6
Picture 3
Indoor
Outdoor
7
5.1.2. Channel Pairing
There are 3 channels for choice. Make sure that both
units are in the same channel so that the machines
could work. Factory default setting is the same.
OutdoorIndoor
Picture 6
9
Outdoor
Indoor
Outdoor
Indoor
Hello!
H
H
Hello!
1 2 3 4
TALK
Press When Talk
Picture 7
10
Note:
1. To save power, the outdoor machine will fall into sleeping mode
if it does not detect operations within 25 seconds. Under sleeping
mode, the indoor machine will unable to talk with the outdoor
machine. However, if anyone clicks the CALL button of outdoor
machine, it will be activated and the indoor machine can talk with
it after receiving the ringing.
2. Under the sleeping mode of the outdoor unit, the indoor unit
cannot talk with the outdoor unit. Only the outdoor mac
hine is
initiated by pressed its bell button, and the indoor machine can
talk after receiving its ringing.
TALK
Press When Talk
11
Frequency table(Table 2)
CHANNEL
FREQ
CDCS CODE
462.7250MHz
462.58750MHz
462.61250MHz
754N
754N
754N
A
B
C
12
Indoor
Outdoor
Picture 8
13 14
Outdoor
Indoor
Outdoor
Indoor
Indoor
A
B
Blue light
2.Additional
indoor unit B
same
channel
1.Additional
indoor unit B
Picture 10
15
A
Indoor
B
Have a
tone
Common Trouble
Intercom works well, but no ring
Both intercom and
ring not working
Outdoor unit does not work
Solutions
Out of pairing, please re-pair it.
16
Outdoor
Click
Indoor/Outdoor
Outdoor
Picture 4
Picture 5
8
INDOOR
Name Function
1. Press the Bell button to cut the ringing.
2. Press the bell to call other intercom
devices which are in the same frequency.
(checking corresponding frequencies and
CDCS CODES in Table 2.)
Re-pairing
key
Volume
Bell
Doorbell
music
Press it to choose your favorite ringings.
There are 20 musics for choice.
Channel
Power
TALK
button
When received a ringing from the
outdoor unit:
1.press once to cut the ringing
2.press and hold the button of the indoor
unit to speak. (speaking time, within 60s).
Led
indicators
TALK
Press When Talk
5
Press and hold for 3 seconds, the
mechine enters into pairing mode.
3 Channels for choice. A, B,C.
Please check and make sure that indoor
and outdoor units' channels are the same.
Please check its corresponding
frequencies and CDCS CODES in Table 2.
Before You Begin
Check that you have all of the included parts. Read the entire
user manual. Read the disclaimer and warning above to
understand your legal rights and responsibilities. If you have
any questions or problems during the installation, maintenance
or use of this product, please contact QNIGLO service team:
[e-mail].
Warning
Never disassemble or pierce the product in any way or the
warranty will not cover the personal disassembled products.
The QNIGLO doorbell, equipped with a wireless intercom
system, combined the doorbell and intercom functions,
realizes to talk with visitors without opening the door.
Better protects the people in the house and more safety
for people living alone.
2
Amazon is the only authorized selling channel of QNIGLO
products. Customers who buy QNIGLO products from all
other channels(except Amazon) could not have QNIGLO
warranty policy and shall take their own responsibilities for all
possible loss. QNIGLO do not have any responsibility to them.
1
QNIGLO intercom doorbell can connect with QNIGLO Intercom
system. Please check Table2 for corresponding channel&code
for connection.
Note:
1. When you set the corresponding Channel&code, doorbell
can talk with our brand intercom.
2. Click the CALL button of outdoor machine, the intercom will
not have ring even set the corresponding channel&code.
However; Click the ON/OFF button for indoor machine, the
intercom will have ring. The outdoor machine can only talk wi
th
intercom, but can not CALL and give a ring alert before talking.
The indoor machine can communicate and make the intercom
ring the bell as well.
17
Blue light indicate pairing status,
Red light indicates the power.
Content
4.1. Charging dock
4.2. USB Cable
*Both indoor and outdoor units need to be charged before use.
*Put them in the charging dock to charge them in turns. There is
a charging indicator in the dock, a red light means charging,
a green light means fully charged. If the indicator light
doesn't turn on, please adjust the units charging position.
1
2
6
6
6
6
6
7
7
7
9
9
9
10
10
12
12
13
13
15
16
17
17
. Disclaimer and Warning
. Product Overview
. Installation
3.1. Included parts
3.2. Installation
3.2.1. Indoor unit installation
3.2.2. Outdoor unit installation
. Charge
4.1. Charging dock
4.2. USB Cable
. Instructions
5.1. Doorbell Function
5.1.1 Power on/off
5.1.2. Channel Pairing
5.1.3. Doorbell
5.2. Intercom Function
.Pairing
6.1. Re-pairing
6.2. Add Additional Units
6.2.1. Adding Extra Outdoor units
6.2.2. Adding Extra Indoor units
. Troubleshoot
. Connect with QNIGLO Intercom System
. Specifications
9
9
. Disclaimer and Warning
Congratulations on purchasing your new QNIGLO product.
The information in the document affects your safety and
your legal rights and responsibilities. Read this entire
document carefully to ensure proper configuration before use.
Failure to read and follow instructions and warnings in this
document may result in serious injury to yourself or others,
damage to your QNIGLO product. This document and all other
collateral documents are subject to change at the sole
discretion of QNIGLO.
By using this product, you hereby signify that you have read this
disclaimer and warning carefully and that you understand and
agree to abide by the terms and conditions herein. You agree
that you solely responsible for your own conduct while using the
product, and for any consequences thereof. You agree to use
this product only for purposes that are proper and in accordance
with all applicable laws, rules and regulations, and all terms,
precautions, practices, policies and guidelines QNIGLO has
made and may make available.
QNIGLO accepts no liabilities for damage, injury or any legal
responsibility incurred directly or indirectly from the use of this
product. The user shall observe safe and lawful practices
including, but not limited to, those set forth in this document.
QNIGLO is the trademark of Shenzhen Crony technology CO.,
LTD. Names of products, brands, etc., appearing in this manual
are trademarks or registered trademarks of their respective
owner companies.
. Product Overview
.Installation
. Charge
. Instruction
5.1. Doorbell Function
5.1.1.Power on/off
Indoor unit
Power on: Press and hold the power button for 3
seconds, there is a ‘beep~’ sound for power on notification.
Power off: Press and hold the power button for 3
seconds, there is a ‘bi,bi’ sound for power off notification.
Outdoor unit
Power on: Press and hold the power button for 3
seconds, there is a ‘beep~’ sound for power on notification.
Power off: Press and hold the power button for 3
seconds, there is a ‘bi,bi’ sound
for power off notification.
5.1.3. Doorbell
When both units are in the same channel, press the outdoor unit
bell key , the indoor unit will be ringing(‘ding dong’ or other
music) to remind visitors. Kindly remind, only the outdoor unit
can start a ringing, indoor unit doesn’t have this function.
5.2. Intercom Function
When people hear the indoor unit’s sounds (‘ding dong’ or music),
they can press any button on the indoor unit to stop the ringing,
And then press and hold the T
ALK button to speak, like "Hello!
Who’s speaking?", then release the button when finished speaking.
(The outdoor unit is the same way for speaking) After receiving the
reply from outdoor unit, press and hold the TALK button to reply.
Both units could be taken off battery and charge the
batteries alone by USB cable.
Here are the steps:
1. Remove the screws of the front cap, then take off the cap.
Pull off the bottom battery and then charge it via USB cable.
(as pictures)
*The outdoo
r unit has a solar panel for auxiliary charging, which
can supply its daily standby power. In order to make sure its
service power, please fully charge it before use.
Note:
1. Please always put the indoor unit in the charging dock to charge
to avoid missing any visitors if out of power.
2. When the outdoor unit is under low battery status, there is a slow
flash red light in its right up corner, please charge it in time.
3. The charging time of both units are around 5 hours, Usually,
the o
utdoor unit could work a year after fully charged.
4. Due the charging time needs hours, in order to avoid missing
visitors, please exchange the indoor unit’s and outdoor units’
batteries.
3. TOT transmission time limit: In order to effectively protect the
circuit device and wireless frequency occupation, the transmission
intercom could not exceed 60 seconds. When the talking time is
over 60 seconds, the machines will have a long beeping sound,
the sound will disappea
r after releasing the TALK key, and the
message could not transfer to other machines. You need to
operate it again within 60 seconds.
4. Short press buttons can call other radio intercom devices
of the same frequency. Press the TALK button to talk. When
setting the same frequency of other devices and the doorbell units,
they could be connected and talk.
Please check the Table 2 for Channel and frequency comparison.
Status Indicator lights
There are 3 colors of the indicator lig
hts, red, green, blue.
Different colors and flashing means different status.
. Pairing
2. Then press the bell button of the outdoor unit, there is a “di”
sound and the blue flash light turns off, it means the pairing is
completed.
6.1. Re-pairing
If the machines are out of pairing, the bell functions will be not
working. Please re-pair it as the following steps:
1. Making sure the channels of both units are the same, press
the indoor pair button, the pairing indicator blue light will be
flashing, it means entering into pairing mode.
6.2. Add Additional Units
6.2.1. Adding Extra Outdoor Units
If adding extra outdoor units to connect with present units,
you need to re-pair them.
Here are the steps:
1. Making sure the channels of the extra units are the same
with the exist units, press the extra outdoor unit’s pairing
button, the indicator blue light will be flashing, it means
entering into pairing mode.
2. Then press the bell button of the original outdoor unit,
there is a “di” sound and the blue flash light turns off, it
means the pair
ing is completed.
6.2.2. Adding Extra Indoor Units
If adding extra indoor units to connect with present units,
you need to re-pair them.
Here are the steps.
1. Making sure the channels of the extra units are the same
with the exist units, press the extra indoor unit’s pairing
button, the indicator blue light will be flashing, it means
entering into pairing mode.
2. Then press the bell button of the original outdoor unit,
there is a “di” sound and the blue flash light turns off, it
m
eans the pairing is completed.
Most issues that arise can easily be resolved by changing the
settings on your intercom doorbell.
Please read this user manual carefully before you use this
machine. Use the table below to find your exact issue and
possible solutions for it. If you need more help, you are
welcome to contact us via our customer service email at
[e-mail].
Indoor
Picture 11
. Troubleshooting
. Connect with QNIGLO Intercom System
Name: QNIGLO DOORBELL
Model: Q358
Dimensions: 59*24*123mm (Machines)
59*10*162mm (Solar panel)
81*56*36mm (Charger dock)
Weight: 340G
Consumption: 30mA (indoor unit)
<100uA (outdoor unit)
Frequency: 462/467MHz
Power: 0.5W
Charging Time: 5 hours
Operating time: 2 days (indoor unit)
6-12 months (outdoor unit)
. Specifications
VOL
VOL
VOL
5V 1A
Outdoor
1
3
4
7
8
9
6
5
2
Indoor
11
Outdoor Indoor
1 2
3
4
5 6
7
8
9
A B C
VOL
5V 1A
A B C
VOL
A B C
VOL
5V 1A
Indoor
Outdoor
A B C
VOL
5V 1A
Indoor
Outdoor
Outdoor
Outdoor
A B C
VOL
TALK
Press When Talk
Step3: Then click the CALL button
of the original outdoor unit A.
Pictures for your reference:
Step1: Check and confirm that it is
in sleeping mode and both units
are in the same channel.
Step2: Press the pairing button of
the new additional indoor unit B,
its pairing blue light will flash.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
This equipment should be installed and oper
ated with a
minimum distance of 0mm between the radiator and your body.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause har
mful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equip
ment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Statement
NOTE 2: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
- DO NOT o
perate the radio without a proper antenna attached,
as this may damage the radio and may also cause you to exceed
RF exposure limits.
A proper antenna is the antenna supplied with this radio by the
manufacturer or an antenna specifically authorized by the
manufacturer for use with this radio.
- DO NOT transmit for more than 50% of total radio use time,
more than 50% of the time can cause RF exposure compliance
requirements to be exceeded.
- This transmitter may operate with the
antenna(s) documented
in this filing in Push-to-Talk and body-worn configurations.
RF exposure compliance is limited to the specific belt-clip and
accessory configurations as documented in this filing and the
separation distance between user and the device or its antenna
shall be at least 2.5 cm.
–This radio is designed for and classified as
“General population/uncontrolled Use”