A1.211210 Qixiang Electon Science & Technoloyg Co.,Ltd. www.anytone.
AT-5555N II 10 METER AMATEUR RADIO Operating Instructions
CONTENTS FUNCTIONS & FEATURES...................................................................1 STANDARD ACCESSORIES.................................................................2 INSTALLATION......................................................................................2 GETTING ACQUAINTED.......................................................................5 HOW TO USE YOUR RADIO................................................................8 KEYPAD FUNCTION..................................
FUNCTIONS & FEATURES ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ ◆◆ Big LCD displays frequency and all kinds of information FM、AM、USB、LSB、PA mode Frequency Tuning Step 100Hz、1KHz、10KHz、100KHz、1MHz ±1.
STANDARD ACCESSORIES Radio Screws for bracket Microphone Pads for bracket Mounting Bracket Adjusting screws Spare Fuses (10A, 125V) Microphone Hanger Self-tapping Screws Non-slip Mat Pads INSTALLLATON Choose the most appropriate setting from a simple and practical point of view. Your radio should not interfere with the driver or crash the driver's knee or leg when rush brake. 1. Using the self-tapping screws and pads(2 sets) to fix the bracket. 2.
ANTENNA INSTALLATION Before using this radio, please install a high efficent and harmonious adjusted CB antenna, suitable antenna type and correct installation will bring excellent communication. To match with the radio, the antenna and cable shall with characteristic impedance of 50ohm, or the antenna system will not efficient enough and will disturb TV, radio or other electronics. 1. Screw the antenna connector into the antenna jack. 2.
Replacing Fuse This radio adopt 15A, 250V fuse. If the fuse blows, determine the reason, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your autho-rized dealer or an authorized servicecenter: 1. Pull the two fuse cover in difference direction and open it. IN-LINE FUSE HOLDER 15A, 250V FUSE 2. Replace the broke fuse with good one, and close the fuse holder. 3.
GETTING ACQUAINTED Front Panel 2 11 12 18 13 14 1 17 16 15 No.
Rear Panel 21 20 23 19 ANT. PA.SP. EXT.SP. POWER + 22 No.
LCD Display 24 25 26 27 7 6 5 11 12 13 14 15 16 1 22 2 21 3 23 4 8 9 10 17 1 RX Signal strength indicator. 2 TX Signal strength indicator. 3 SWR strength indicator. 4 Model name Indicator. 5 18 19 20 Appears when the Keypad lock function is ON. 6 FUNC Appears when press MENU key. 7 EMG Appears when using Emergency channel. 8 Appears when adjust SSB clarifier frequency. 9 AQ Appears when use ASQ. 10 SC Appears when scan function is ON.
HOW TO USE YOUR RADIO OFF/ON Radio 1. Turn VOL clockwise to switch on the radio, the radio emit a beep. When the LCD displays frequency or channel, the radio is on. 2. Turn VOL anti-clockwise to switch off the radio, the radio is OFF when hear Ka Ta from the switch. Volume Control When the radio is turned on, turn VOL clockwise will increase the volume, turn VOL anti-clockwise will reduce the volume. The LCD displays VOL: XX (XX stands for the volume level, total 1-36 levels).
Frequency control 1. In frequency mode, press【PUSH】key, then you can adjust frequency for present channel. 2. When the frequency is flashing, turn CH clockwise to increase frequency, anticlockwise to reduce frequency. 3. When the frequency is flashing, press【PUSH】again to adjust frequency step size. KEYPAD FUNCTION 【MENU+MODE】 Press【MENU】and【MODE】together to enter weather channel mode. 【FRQ/REP】 Short press【FRQ】to switch between frequency display mode and channel display mode. Offset Direction Function 1.
CTCSS/DCS Function 1. Long press【MODE】for 2 seconds to enter CTCSS/DCS function, LCD displays "CTCSS" or "DCS"; 2. Press【PUSH】to set CTCSS/DCS, turn channel switch to select CTCSS/ DCS, then Press【PUSH】to store and exit. OFF: Turn off CTCSS/DCS function; CTCSS: 67.0~250.3Hz, Total 38 groups; DCS: D023N~D754N, Total 104 groups; Note: This function is available only when install Optional CTCSS board. 【DW/+10K】 Dual-Watch function 1. Short press【DW】to turn on Dual watch, LCD displays "DW"; 2.
【SCAN/SKP】 Scan function 1. Short press【SCAN】to enter scan function, LCD displays "SC"; 2. In scan mode, Turn channel switch will change scan direction. 3. Short press【SCAN】again to exit. Add/delete scan list function 1. Long press【SCAN】for 2 seconds to add or delete the current channel from scan list; 2. When LCD displays "●", current channel is not added to scan list; When LCD does not display "●", current channel is added to scan list. 【MEM/STOR】 Using memory channel: 1.
BACKGROUND FUNCTION MENU OPERATION 1. 2. 3. 4. 5. Press【MENU】for 2 seconds to enter menu list; Turn Channel switch to select menu No.1 to No.10; Press【PUSH】to enter the menu setup; Turn channel switch to select wanted setup; Press any other key or wait 5 seconds, the setting will be stored and exit. No. Function LCD Display Values and Descriptions 1-36, Total 36 levels available; Default: 25.
No. 11 Function Offset frequency LCD Display Values and Descriptions Frequency range: 100Hz~5MHz; Default: 100KHz. 12 VOX level 01~09: Total 9 Levels for VOX delay time set. Default: OFF. 13 VOX delay 01~09: Total 9 Levels for VOX delay time set. Default:04 14 Echo volume 01~32: Total 32 Levels for echo volume. Default:19 15 Echo delay 01~32: Total 32 Levels for echo delay time set. Default:19 16 Weather alert OFF: Shut weather alert function; ON: Open weather alert function; Default:OFF.
SPECIFICATIONS GENERAL Frequency Range 28.000-29.700MHz(Programmable) Frequency Band Channel A/B/C/D/E/F/G/H/I 40channels(programmable)in each band Frequency Control Frequency Step Phase-Locked-Loop Synthesizer 100Hz、1KHz、10KHz、100KHz、1MHz Frequency Tolerance ±5.00ppm Temperature Range -20℃ to +50℃ Microphone with push-to-talk /UP/DN and coiled cord Input Voltage 13.8V Dimensions (in mm) 283(L)x200(W)x60(H) Weight 1.
RECEIVER SSB: 0.25μV for 10dB(S+N)/N at greater than 1/2-watt of audio output Sensitivity AM:1.0μV for 10dB(S+N)/N at greater than 1/2watt of audio output FM: 1.0μV for 20 dB (S+N)/N at greater than 1/2 watt of audio output Adjacent-Channel Selectivity AM/FM: 60dB Image Rejection More than 65dB SSB: 70dB AM/FM: 10.695MHz 1st IF, 455KHz 2nd IF IF Frequency SSB: 10.