A1.
518UV II INSTRUCTION MANUAL
THANK YOU! transceiver will provide you with reliable, clear and efficient communication service. The transceiver introduces innovative DSP digital signal processing technology, high degree integration, it is including kinds of professional function, best stability and great reliability as well as exterior smooth lines, novel, fashionable, sturdy and durable. The transceiver is including plenty of TX, RX channels, as well as UU, VV and UV standby modes, can be single U or V band by operation.
CAUTIONS transceiver is excellent designed with advanced technology. The following tips will be helpful for you in performing your obligation under warranty and understanding the safety of transceiver usage. 1.Keep the transceiver and accessories away from children. 2.Please do not try to open or modify the transceiver without permission, non-professionals operation may also cause damage. 3.Please use assorted battery and charger to avoid damage. 4.
TABLE OF CONTENTS UNPACKING ................................................................................................................................................................................................ 01 Supplied Accessories ......................................................................................................................................................................... 01 STANDARD ACCESSORIES/ADDITIONAL ACCESSORIES ................................................
TABLE OF CONTENTS Receiving ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 13 Transmitting ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 13 Emergency Alarm ��������������������������������������������������������������
UNPACKING Please carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please contact with dealers immediately.
STANDARD ACCESSORIES/ADDITIONAL ACCESSORIES Standard Accessories Antenna*1 QA11UV 155/435MHz Li-ion Battery QB-40L Battery Charger AC Adaptor QPS-07 QBC-40L Belt Clip BC09 Instruction Manual *1.Note: For frequency band of antenna, please refer to label indicated in the bottom of the antenna. Additional Accessories USB Programming Cable PC03 Programming Software Handheld Microphone QHM22 02 QPS518UV_1.
BATTERY INFORMATION Charging Operation The battery is not charged at the factory, please charge it before use. Charge the battery for the first time after purchase or extended storage (more than 2 months) may not bring the battery to its normal operating capacity. After repeating fully charge/discharge cycle for two or three times, the operating capacity will reach the best performance. The battery life is over when its operating time decreases even though it is fully and correctly charged.
BATTERY INFORMATION ▲▲ Do not recharge the battery if it is already fully charged. This may shorten the life of the battery or damage the battery. ▲▲ Do not charge the battery or transceiver if it is damp. Dry it before charging to avoid danger. WARNING: When keys or ornamental chains and other electric metals contact with the battery terminals, the battery may cause damage or hurt bodies.
BATTERY INFORMATION NOTE: When charging a power-on transceiver equipped with battery, the LED will not turn into green to show the full charge status. Only when turn off the transceiver, the LED can indicate normally. Because when the transceiver is power on, it would consumes energy, the charger cannot detect when battery has been fully charged, the charger will charge battery in voltage consumption and fail to indicate correctly. 5.
BATTERY INFORMATION Charging Prompt 1.Self-examination: When charging, ORANGE light twinkles for 1 second and goes out. That means the charger has passed its self-examination and it can charge the battery normally. If the light remains orange or the red light twinkles, which means the charger can not pass its self-examination or charge the battery. 2.
GETTING ACQUAINTED LCD Display On LCD display screen, you will see various icons which stand for the selected functions and sometimes you may forget the meaning of them. Here you will find the following table extremely useful.
GETTING ACQUAINTED 1 2 3 4 7 10 8 9 5 1 FM 7 REV S.
GETTING ACQUAINTED 1 Antenna 2 Selector Knob 3 Power / Volume Switch Rotate it clockwise to turn on transceiver, rotate it anticlockwise until heard "click" to turn off the transceiver. When transceiver is power on, rotate it clockwise to increase volume, anticlockwise to reduce volume.
BASIC OPERATIONS Turn the Radio On & OFF Under power-off state, please turn [POWER]/[VOLUME] clockwise to turn on the transceiver. Under power-on state, please turn [POWER]/[VOLUME] anticlockwise to turn off the transceiver. Adjusting Volume Under power-on state, turn [POWER] /[VOLUME] to adjust volume. Clockwise-up, anticlockwise -down. When adjusting the volume, user can press the key programmed as Squelch Off to monitor current volume firstly.
BASIC OPERATIONS Switch between Main band and Sub band Under standby state, press key to switch channel between Main band and Sub band. Arrow directs the current operational channel. Switch between Channel mode Under standby state, press . key to set main band as Channel mode Channel Adjusting When transceiver in Channel mode or FM radio channel mode, rotate channel switch to adjust channel.
BASIC OPERATIONS NOTE: Channel step:2.5K) 5K) 6.25K) 10K) 12.5K) 20K) 25K) 30K and 50KHz in total 9 for optional. FM radio step frequency is 50K. Channel Input by Keypad Under channel mode of transceiver or FM radio, you can switch to desired channel by entering three numbers (001-199). If the entered channel is not in edited channel range, the transceiver will emit beep to prompt wrong input and return to current channel. For example, entering 001 is channel 1, 030 is channel 30, 125 is channel 125.
BASIC OPERATIONS FM Channel Searching When transceiver in FM radio mode, press key, LCD displays " " icon, then press to start FM searching. When one station is sought, LCD displays current station frequency, you can listen to current station. Squelch Off Momentary / Squelch Off Side key [PF2] can be setup for Squelch off Momentary or Squelch off function by programming software. 1.Squelch off: Press [PF2] key, squelch circuit is not mute, back-ground noise can be heard.
BASIC OPERATIONS it is not busy, press [PTT] key and talk to speaker. Please keep the distance between mouth and speaker to be 2.5-5CM, speak in normal tone to get the best acoustic fidelity. Note: When press and hold PTT key, transceiver is transmitting if the red LED light is on, release [PTT] key to receive calls. Emergency Alarm Under standby state, press and hold [PF1] key which is programmed with ALARM function until LCD displays "ALARM", Emergency alarm function is started.
BASIC OPERATIONS Switch between Main band and Sub band Under standby state, press key to switch channel between Main band and Sub band. Arrow directs the current operational channel. Switch between Channel mode Under standby state, press . key to set main band as Channel mode Channel Adjusting When transceiver in Channel mode or FM radio channel mode, rotate channel switch to adjust channel.
BASIC OPERATIONS switch into channel mode, channel number flashes. 2. Rotate channel switch to select desired deleting channel number. key, the top left corner of LCD displays " " icon, press and hold key until transceiver 3. Press emits "DUDU" beep and clear up frequency information of current channel, deletion is successful. Note: This process can be applied for deleting FM radio channels.
BASIC OPERATIONS Turn On/ Off FM Radio Under standby state, press key, the top left corner of LCD displays " " icon, then press key, LCD displays "FM ON" and current FM radio frequency, FM radio function is on. When FM radio is on, press key, LCD displays "FM OFF", FM radio is mute. When FM radio is on, press key, the top left corner of LCD displays " " icon, press key to turn off FM radio and return to transceiver state. Re-start transceiver also can exit FM radio function.
BASIC OPERATIONS DCS signaling, it will stay 5seconds and then go on scanning. Press any other keys except , , key to exit. NOTE: This function is invalid when transceiver works in professional mode or the arrow directed channel no setting CTCSS/DCS signaling. In current channel, if signaling set as CTCSS, it will scan CTCSS, if sets as DCS, will scan DCS.
BASIC OPERATIONS Channel Scan key, the top left corner of LCD displays " Under corresponding mode, press key to start frequency scan or channel scan. " icon, then press 1. Channel Scan Under channel mode, this function is used for monitoring signal of each channel in this mode. Press numeric key or key to exit. NOTE: ▼ Frequency scan is of all bands scan) it scans upwards as your STEPPING setting. ▼ In channel scan) the skipped channel is not in the line of scanning. Scan upwards as per channel no.
BASIC OPERATIONS 1. LCD displayed " S " means the current channel will not be scanned. 2. " S " icon disappeared means the current channel will be scanned. Frequency Reverse Under standby state, press key, the top left corner of LCD displays " " icon, then press key to set arrow directed channel as frequency reverse, repeat above operation to turn off frequency reverse. 1.
BASIC OPERATIONS 3. Press [PF1], [PF2] or NOTE: During timing, press key to exit stop watch function. key to stop timing and displays current data, press this key again to clear timer. DTMF code Transmit and Enquiry 1. Press key, the top left corner of LCD displays " " icon, then press key, LCD displays DTMF data and group number (total 16 groups) of current group. 2. Rotate channel switch to choose desired group and DTMF data, press PTT key to transmit selected DTMF signaling.
BASIC OPERATIONS Single-band Switching To avoid interference from the sub channels when main channel in use, you can use the single band switching function to turn off sub channel band quickly. 1. In standby mode, press band will be turned off. key, the radio will display the upper band, the lower 2. Press key again, the radio will display the lower band, the upper band will be turned off. 3. Press 22 key again to return to dual band display.
FUNCTION MENU SETUP Menu 1-13 of this transceiver are channel operations. Channel operations temporarily changed the functions of current channel. When power off or channel has been changed, the relevant setup will be erased. The operating methods are as follows: key, the top left corner of LCD displays " " icon, then press key to enter function menu. 1. Press 2. Press / key to choose desired function. key to choose CTCSS) DCS or off.
Function Menu Setup OFF No CTCSS/DCS encode/decode 62.5HZ-254.1Hz+Self defined 51 groups fixed CTCSS encode/decode + 1 group self-defined CTCSS encode/decode 000N-777I 1024 group DCS encode/decode 3 RT-CDC CTCSS/DCS Encode/Decode Synchronous 4 TONDEC Optional signaling DTMF setup SQ CTCSS/DCS 5 SIGNAL Squelch mode setup TONE CT&TO CT/TO 6 24 STEP Frequency step size setup 2.5K-50K Current optional signal is DTMF.
Function Menu Setup 7 W/N Wide / Narrow Band Selection 25K/12.5K Wide band/Narrow band 8 REV Frequency Reverse ON Turn on Frequency reverse function, TX and RX frequency of current channel will be interchanged. OFF Close Frequency reverse function. TX=RX Turn on Talk Around function, current channel will transmit at RX frequency, if CTCSS/DCS signaling is set, it will interchange decoding CTCSS/DCS as encoding. OFF Close Talk Around function.
Function Menu Setup 15 26 DSPSUB Sub band display setup FREQ Display sub band frequency or channel VOLT Display current battery voltage OFF Sub band display is disabled ON/OFF Turn on/off keypad voice prompt function OFF Turn off time-out timer 10-270S Total 27 levels of TOT for optional, each interval is 10S OFF Turn off VOX function 1-10 Total 10 VOX levels for optional 16 BEEP Keypad Voice prompt setup 17 TOT Time-Out-Timer 18 VOX Voice Operated Transmission (VOX) Setup 19 V
Function Menu Setup FUNCT 24 FTIME Function Icon Stay Time 1SEC-3SEC ALWAYS ON/OFF AUTO When finished function setting or enter into function menu, icon disappeared. When finished function setting or enter into function menu, icon stay 1-3seconds then disappeared. Function icon is always display, only when pressing function key again, the icon will disappear. Always on/off Backlight will automatic closed after a period.
FUNCTION MENU SETUP Display Mode Setup There are three kinds of display modes for optional. 1. Press [PF2] key to turn on radio, hold [PF2] key until transceiver emits beep. 2. Press / key to choose No. 01 function item, it shows "DSP" on LCD. 3. Rotate channel switch to choose desired setup. FREQ: Frequency + Channel mode, transceiver displays current channel name key to switch into VFO mode.
FUNCTION MENU SETUP OFF: No operations. FACT: Resume all items to factory default, including channel and background settings. INIT: Resume background settings to factory default, channel operations are keeping. 4. Press key to exit current selection. 5. Press key to confirm current selection. Note: In power off state, hold key to power on radio, the radio will resume to factory default.
TECHNICAL SPECIFICATION General VHF:136~174MHz Frequency Range UHF:400~480MHZ (EX:400~520MHz) Channel Capacity 200 channels 25KHz (wide band) Channel Spacing 12.5KHz (narrow band) Phase-locked 0.1KHz Step Operation Voltage 7.4V DC ±20% More than 12 Hours(1350mAh), by Battery Life 5-5-90 working cycle Frequency ±2.5ppm Stability Operation -20℃~ +55℃ Temperature Size 127x61x36.
TROUBLE SHOOTING GUIDE Problem Corrective Action No power A.The battery may be exhausting. Recharge or replace the battery. B.The battery may not be installed correctly. Remove the battery and install it again. Battery power dies shortly after charging. No sound after using earphone. for a while The battery life is finished. Replace the battery pack with a new one. Earphone jack is broken. Please contact with local dealers to repair. Cannot talk or hear other members in your group A.
The SAR limit of USA (FCC) is 8 W/kg averaged over one gram of tissue. Device types 518UVII (FCC ID: T4K3208UV) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 2.366 W/kg and for head is 3.990 W/kg. . This device was tested for typical body‐worn operations with the back of the handset kept 25mm from the body.