User's Manual

8.2 Function menu
Click in Main Menu to enter function menu
8.3 Widget
8.4 Operation background
Click to look into background operation situation.
9.Battery management and charging
A.Before first operation, the unit should be recharged for
5~6 hours to make sure the battery is fully charged.
B.Connect the Power adapter to the device; the battery
icon on desktop displays as[ ], and green bar is rolling,
which means the device is charging. Don't unplug the
charger in charging. After fully charged, the battery icon on
desktop displays as[ ], and the green bar stops rolling.
Note: Lithium battery doesn’t need to recharge after power fully
runs out.
10.3 IP address setting and connecting: two ways
A. Auto Obtain IP address:
System default is IP address auto obtaining, click the
target network name, input password if it is required to,
click “KW” network as picture below to pop up Password
Input Window; input right password, and click it; after
through KW network's verification, system will auto obtain
IP address from KW network, as shown in figure below:
10.2 WIFI setting and WIFI network
Click ”Scan”, system will search WIFI network automatically,
and display signal strength.
B. Manually Obtain IP address:
Place a check mark in “Advanced”, and select “Static”
in“IP setting”; click “connect” and the setting will be
effective.
Disclaimer: We try to ensure its correctness and integrity
manual, but it is hard to avoid any mistake and omission.
Please take material object as the standard. Our company is
derelict of duty for mistake and omission that may exist.
of the
User's Manual
7
8 9 10 11
11.WIFI setup
11.1 Turn on WIFI
Click to enter setup menu, select “On” in Wi-Fi
option, as shown in figure below:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
10.Operation Guide for Bluetooth:
1.Enter into the Setting Menu, find out Bluetooth, turn it on
(move the button of “OFF” to right side “ON”).
2.Click the “SEARCH FOR DEVICES” on the right-top side
of the window, waiting for a few seconds, then the
scanned Bluetooth Devices will be listed, click the proper
device.
3.Click “Pair”, after pairing, then the files can be transferred
by Bluetooth.
12.Technical Specifications
Panel Size:
Panel Resolution:
Touch Panel Type:
CPU:
Operating System:
RAM:
Flash:
External Storage:
Built-in Speaker:
WIFI:
G-sensor:
Power Input:
Battery:
Product Size:
Device Weight:
8 inch Widescreen
1280x768 Pixels
5-point Capacitive Touch Panel
ARM Cortex A9 Dual-core, Frequency
1.5GHz max, 512K L2 Cache
Google Android 4.2
1G
8G Nand Flash
Micro SD Card (Max 32GB)
USB OTG(a. connect to PC for data
transfer; b. Connect to USB Stick via
the USB Host Cable.)
Stereo Speaker 8ohm x 1 (1W)
IEEE 802.11b/g/n
3(X/Y/Z )Axis
AC 110~240V 50/60Hz; DC 5V/2.0A
Model No. of Power adapter:
PA010B-05020EU
Lithium Polymer Battery 5000mAh
3.7V Model No. of Power adapter:
BP4362157
213x138.5x11.2mm(L x W x H)
Approx. 490g
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
changes or modifications not expressly approved by the party
responsible for compliance could void the user ’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End user must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
The portable device is designed to meet the requirements for
exposure to radio waves established by the Federal Communications
Commission (USA). These requirements set a SAR limit of 1.6 W/kg
averaged over one gram of tissue. The highest SAR value reported
under.
this standard during product certification for use when properly worn on
the body is 0.550 W/kg.