Installation & Operation Guide Touchscreen Door Lock
Index INSTALLATION INSTRUCTIONS Package Contents / Tools Required .......................................................... Page 1 Prepare Door and Jamb ..............................................................................Page 2 Adjusting Deadbolt Latch Set .....................................................................Page 3 Installing Deadbolt Latch Set ..................................................................... Page 4 Installing Interior Assembly ........................
INSTALLATION INSTRUCTIONS Battery Cover Interior Assembly 5/16"(8mm) Screws (2ea.) Strike Plate Optional 3/4"(19mm) Screw (1ea.) 3/4"(19mm) Screws (4ea.) Mounting Plate Touch Keypad Assembly 1"(25mm) Screw (1ea.) 1-1/8"(28mm) Screws (2ea.
PREPARE DOOR AND JAMB NOTE: For installation on doors with pre-drilled holes skip to page 4. 1. TEMPLATE a. Cut out template printed on page 14 of this Manual (Figure 1a). b. Fold template and place on door 36” (915mm) from the ground as marked (Figure 1b). 2. MARK THE DOOR FOR DRILLING b. Mark center hole on door edge through guide on template for 1” (25mm) latch bolt (Figure 2a). a. Mark center hole on door face through guide on template for 2-3/8” (60mm) or 2-3/4” (70mm) (Figure 2b). backset 3.
ADJUSTABLE DEADBOLT LATCH SET NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm) Measure the backset (backset is distance between edge of the door and the center of Lock). 1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 1a). b. Rotate the cylinder cover clockwise (Figure 1b). c. Pull and twist the extension plate all the way out (Figure 1c). d.
INSTALLING DEADBOLT LATCH SET 3. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver) a. Insert Deadbolt Latch Set into door edge hole with the word “UP” and the arrow on the extension plate facing UP. Cross shaped spindle connector will be at the bottom of the Deadbolt Latch Set (Figure 3a). b. Make sure the face plate sits with the door. Do not force the latch into the mortise Chisel out excess material if necessary for a c. Using two 3/4” (19mm).
INSTALLING INTERIOR ASSEMBLY 5. UNPACK THE INTERIOR ASSEMBLY a. Remove the battery cover by sliding the cover upward. b. Locate the screws holding the Mounting Plate to the Interior Assembly. Remove the screws to release the Mounting Plate from the Interior Assembly. 6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR a. Gently move the switch to “L” for Left Handed Door (Figure 6a). b. Gently move the Switch to “R” for Right Handed Door (Figure 6b).
INSTALLING EXTERIOR ASSEMBLY 8. INSTALLING THE EXTERIOR ASSEMBLY Work with the Door Open for easy access. a. Unpack the Exterior Assembly. Use care to not scratch the green circuit board during handling and installation. b. Check that the Rubber Gasket is properly seated on the Exterior Assembly (Figure 8a-b). c. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set cross shaped spindle connector in the HORIZONTAL POSITION.
INSTALLING INTERIOR ASSEMBLY (CONT.) 11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY a. Use care to attach the Control Wire male plug to the Interior Assembly female socket connector (Figure 11a). b. Do not force the Control Wire male plug into the Interior Assembly female socket connector (Figure 11b). c. The Control Wire male plug has two alignment tabs on the smooth side of the plug which is the top of the plug (Figure 11c). d.
INSTALLING INTERIOR ASSEMBLY (CONT.) 13. Installing Batteries a. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad will illuminate blue, and the Clevr button will green twice to signify that it has received power (Figure 13a). NOTE: Do not touch the Keypad until the blue light turns off. Do not use rechargeable batteries or non-alkaline batteries. b.
OPERATION INSTRUCTIONS Exterior Assembly Overview Green • Indicates • Indicates Red • Indicates • Indicates Successful Programming Step Unlocking is Successful Failed Programming Step Locking is Successful Lock button Lock - Used to lock door Clear - Used to clear wrong keypad entries Unlock button Unlock - Used to unlock door Programming - Used in programming steps Batteries (not included) Electronic lock requires (4) High Quality AA Alkaline batteries.
LOCKING/UNLOCKING/PASSWORD PROGRAMMING TO UNLOCK THE LOCK Using Keypad: Enter a valid User Code (default code is 123456) and press 1 beep and lights green. TO LOCK THE LOCK Using Keypad: Press and hear and then hear 2 beeps and lights red. Changing Programming Code CHANGE CURRENT OR PRESE TPROGRAMING CODE PC Factory default Programming Code PC = 123456, this is the master password for your lock. All programming functions require this code.
DELETE ONE EXISTING OR PRESET USER CODE The unit comes with a factory User ID ID = 01 for User Code UC = 123456. IMPORTANT: To delete 1 User Code UC , the lock must have more than 1 User Code in its database. PC 2 Existing ID re-enter UC ID Hear 1 beep and Light Indicator illuminates green. DELETE ALL USER CODES IMPORTANT: this will delete the user codes but not the programming code, enter the following. PC 3 re-enter PC Hear 1 beep and Light Indicator illuminates green.
Warning sounds and LED down for 30 seconds. red after 3 incorrect code attempts: Keypad shuts Bluetooth on and off PC 7 PC 7 1 beep Bluetooh off 2 beep Bluetooh on Restore Factory Settings To reset the lock to the original factory settings including the Programming Code PC and all User Codes UC remove one battery for 10 seconds. Reinsert the battery and wait for a long and short beep. Press 3 times within 3 seconds. The lock will beep and the light indicator will turn green.
Issue Solution Latch Working BackwardsLock unlocks when lock button is pushed or locks when unlock button or code is pushed. Direction switch is set to incorrect setting. Remove the Interior Assembly and move the switch to the opposite direction. • Check that your switch is set in the correct position Left or Right Handed door. If Correct • Rotate Interior Knob and reinstall Interior Assembly. Retest again while holding Interior Assembly in place. Interior Knob will not turn.
Page 14 MARK FOR 1-3/8” (35mm) DOOR THEN DRILL 1” (25mm) HOLE IN CENTER DOOR OF EDGE 2” (50mm) IN DEPTH MARK FOR 1-3/4” (45mm) DOOR IMPO RT ANT! PLACE TEMPL ATE ON HIGH EDGE OF DOOR BEVEL PLACE TOP 36” (915mm) ABOVE FLOOR DRILL 2-1/8” (54mm) HOLE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.