Installation & Operation Guide Touchscreen Door Lock
Index INSTALLATION INSTRUCTIONS Package Contents / Tools Required .......................................................... Page 1 Prepare Door and Jamb ..............................................................................Page 2 Adjusting Deadbolt Latch Set .....................................................................Page 3 Installing Deadbolt Latch Set ..................................................................... Page 4 Installing Interior Assembly ........................
INSTALLATION INSTRUCTIONS Battery cover Optional1”(25mm) Screw(1ea.) 5/16”(8mm) Screws(2ea.) 3/4”(19mm) Screws(4ea.) 1”(25mm) Screws(1ea.) Strike Plate Interior Assembly Touch Keypad Assembly Mounting Plate Key Latch 5/16”(8mm)Screws-2ea. 3/4”(19mm)Screws-4ea 1”(25mm)Screws-3ea. Interior Assembly Mounting Plate Entry Keys (2ea.) Touch Keypad Assembly Strike Plate Deadbolt Latch Set (Adjustable) 2-3/8”(60mm)to 2-3/4”(70mm) 1”(25mm) Screws-1ea.
PREPARE DOOR AND JAMB NOTE: For installation on doors with pre-drilled holes skip to page 4. 1. TEMPLATE a. Cut out template printed on page 14 of this Manual (Figure 1a). b. Fold template and place on door 36” (915mm) from the ground as marked (Figure 1b). 2. MARK THE DOOR FOR DRILLING b. Mark center hole on door edge through guide on template for 1” (25mm) latch bolt (Figure 2a). a. Mark center hole on door face through guide on template for 2-3/8” (60mm) or 2-3/4” (70mm) (Figure 2b). backset 3.
ADJUSTABLE DEADBOLT LATCH SET NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm) Measure the backset (backset is distance between edge of the door and the center of Lock). 1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 1a). b. Rotate the cylinder cover clockwise (Figure 1b). c. Pull and twist the extension plate all the way out (Figure 1c). d.
INSTALLING DEADBOLT LATCH SET 3. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver) a. Insert Deadbolt Latch Set into door edge hole with the word “UP” and the arrow on the extension plate facing UP. Cross shaped spindle connector will be at the bottom of the Deadbolt Latch Set (Figure 3a). b. Make sure the face plate sits with the door. Do not force the latch into the mortise Chisel out excess material if necessary for a c. Using two 3/4” (19mm).
INSTALLING INTERIOR ASSEMBLY 5. UNPACK THE INTERIOR ASSEMBLY a. Remove the battery cover by sliding the cover upward. b. Locate the screws holding the Mounting Plate to the Interior Assembly. Remove the screws to release the Mounting Plate from the Interior Assembly. 6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR a. Gently move the switch to “L” for Left Handed Door (Figure 6a). b. Gently move the Switch to “R” for Right Handed Door (Figure 6b).
INSTALLING EXTERIOR ASSEMBLY 8. INSTALLING THE EXTERIOR ASSEMBLY Work with the Door Open for easy access. a. Unpack the Exterior Assembly. Use care to not scratch the green circuit board during handling and installation. b. Check that the Rubber Gasket is properly seated on the Exterior Assembly (Figure 8a-b). c. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set cross shaped spindle connector in the VERTICAL POSITION.
INSTALLING INTERIOR ASSEMBLY (CONT.) 11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY a. Use care to attach the Control Wire male plug to the Interior Assembly female socket connector (Figure 11a). b. Do not force the Control Wire male plug into the Interior Assembly female socket connector (Figure 11b). c. The Control Wire male plug has two alignment tabs on the smooth side of the plug which is the top of the plug (Figure 11c). d.
INSTALLING INTERIOR ASSEMBLY (CONT.) 13. Installing Batteries a. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad will illuminate blue, and the Clevr button will green twice to signify that it has received power (Figure 13a). NOTE: Do not touch the Keypad until the blue light turns off. Do not use rechargeable batteries or non-alkaline batteries. b.
OPERATION INSTRUCTIONS Exterior Assembly Overview OPERATION INSTRUCTIONS Item Administrator password 1 Capacity Password Fingerprint Bluetooth Card 50 99 50 50 Permissions Add / Delete/ Clear User password/ Finger register/ administrator password. Reset Unlock Unlock Unlock; Send E-key; Check records Unlock TO UNLOCK THE LOCK Using Keypad: Enter a valid password (Default password is :123456) and press key.
LOCKING/UNLOCKING/PASSWORD PROGRAMMING Using valid Finger user Using valid Card (This function is not available for the US market.) Using APP TO LOCK THE LOCK 2.1 Using Keypad: Enter press key. 2.2 Setting Automatic Lock ( 1-30 second) Default 10 second 1.
FINGERPRINT MANAGEMENT Enter user ID number (2 digits ), press the key, the input 4-8 digits for a new password, press key. Input again the same numbers and press key, Voice prompt "Add success". 2.1.2) Delete password Press 2 to delete password. Voice navigation "Please enter the user number to be deleted ", Enter user ID number press key, Enter the user ID number again and press the key, the voice prompt "Delete success". 2.1.3) Clear password Press 3 to clears the password.
CARD / PASSWORD MANAGEMENT / AUTOMATIC LOCK SETTING 2.2.3) Clear fingerprint Press 3 to empty the fingerprint. Voice navigation “Enter administrator password press the key”. Voice navigation "the fingerprint has been cleared" 2.3.Card management Press 3 to set user card (This function is not available for the US market.) Add user card press 1, Delete user card press 2, Clear user card press 3, Return press key. 2.3.
BLUETOOTH SETTING / VOICE PROMPT / RESTOR FACTORY SETTING Press 0 turn on or off the automatic Press 5 to set automatic function. time. The input digital " 3-30 " will be the automatic lock time 2.6. Turn on or off Bluetooth Follow the voice navigation, press 6 to turn on or off Bluetooth. 3. Turn on or off voice prompt Touching to light up the password tray, press three times key to turn on or off voice prompt. 4.
BACK OF TEMPLATE Page 14
Page 15 MARK FOR 1-3/8” (35mm) DOOR THEN DRILL 1” (25mm) HOLE IN CENTER DOOR OF EDGE 2” (50mm) IN DEPTH MARK FOR 1-3/4” (45mm) DOOR IMPORTANT! PLACE TEMPL ATE ON HIGH EDGE OF DOOR BEVEL 2-3/4” (70mm) BACKSET 2-3/8” (60mm) BACKSET PLACE TOP 36”(915mm) ABOVE FLOOR DRILL 2-1/8” (54mm) HOLE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.