User's Manual
Please read the user manual before using the product.
Go to www.mi.com to learn more
Manufacturer: Qingdao Yeelink Information Technology Co., Ltd.
Address: 10F-B4, Building B, International Innovation Park, 1 KeYuanWeiYi Road, Laoshan,
Qingdao, Shandong Province, People's Republic of China
115mm(±0.5)
460mm(±0.5)
115mm(±0.5)
Specications
Product Features
Off-delay Timer Mobile Control
Four Lighting Modes
Firmware Upgrade
On/off Timer
The Focus Mode
Eye Protection
* Factory Reset is required in a
new network environment to
reconnect the network.
Mi LED Desk Lamp
User Manual
115mm(±0.5)
460mm(±0.5)
115mm(±0.5)
Smart Control
1. Scan the QR code below or go to App store to download Mi Home App.
2. Make sure that the lamp is on. Open the application and follow the instructions in
the application.
Factory Reset
The Reset hole is at the bottom of the lamp base. When powered on, insert a
straightened tool into the hole for 5 seconds, and let go when the lamp starts to
breathe. The Reset completes when the breathing stops.
* Make sure that the Wi-Fi network is available
and is able to access the Internet properly.
Press the knob to
turn on/off the light
Spin the knob to
adjust the brightness
Press and spin the knob to
adjust the color temperature
1. Please confirm that the input voltage is right. The use of inappropriate voltage may
damage the product and bring safety hazards.
2. For indoor use only.
3. Regularly check the power cord, AC adaptor, and other components . If any parts
are compromised, the product should no longer be used.
4. Use standard adaptors only. Misuse of adaptors may damage the product and bring
safety hazards.
5. Keep the product away from liquids and humid environments.
6. The LED module can not be replaced.
7. Do not disassemble the product. The light-emitting diode may cause damage to your
eyes.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.
Adjustable brightness
Adjustable color
temperature
UserManual
Model: MJTD01YL
Operating temperature: -10℃ to 40℃
Operating humidity: 0%-85%RH
Lamp input: 12V 0.5A
Rated input: 100-240V~ 50/60Hz 0.2A
Power factor: 0.4
Color temperature range: 2700-6500K
Luminous flux: 300 lumens
Life expectancy: approx. 25000h
Compatible with: Android & iOS
Rated input power:
6W (42pcs×0.15W/LED Module)
Wireless connectivity:
Wi-Fi IEEE 802.11b/g/n 2.4GHz
1. Unpack the product and plug it into a power supply.
2. Press the knob to turn on the light.
Instructions
Warning
FCC Compliance Statement
Rotary Knob
Power Cable
Body
135°Adjustable
Power Hole
To satisfy FCC RF Exposure requirements for this transmission devices, a separation
distance of 20cm or more should be maintained between the antenna of this device
and persons during operation. To ensure compliance, operation at closer than this
distance is not recommended. The antenna(s) used for this transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.