7KDQN \RX IRU EX\LQJ RXU SURGXFW :DUQLQJV Please read this manual carefully so that you can understand and use the projector correctly. After reading, please save this manual for future reference. 1RWLFH The specifications are subject to change without notice. The manufacturer is not responsible for typographical errors, incorrect images, product descriptions and specifications. $ERXW WKH EUDQG VGA&XGA is the registered trademark of International Business Machines Corporation.
$FFHVVRULHV Remote Control Power Cord (2 m) Paired Composite, Analog Audio cable. (1.5 m) Owner’s Manual Warranty Card Batteries for Remote Control 1RWLFH To project a clear image it might be necessary to adjust the contrast ratio, brightness, focus and keystone. The image may look blurry or skewed without these adjustments.
&KDSWHU 3UHSDUDWLRQ 6HFWLRQ 6HW 8S 6HWWLQJ There are two methods to project this projector, please choose the best method base on the condition of the place. 1. Table top: Place projector on table or shelf keeping the projector in line with the screen. 2. Suspended: Hang the projector from the ceiling with appropriate ceiling mount. 1RWLFH You need to use a projector ceiling mount if you want to suspend the projector from the ceiling.
&RQQHFWLQJ D FRPSXWHU Please turn off the power of the projector and signal before connecting a VGA source while the power is on may result in operational errors. Please confirm the type of connector fits the input on the projector, the projector can be damaged if the wrong connector is inserted. Set projector to the “VGA” by using the button “PC/ AV”. Refer to the VGA source manual to configure the source resolution and frequency.
The Infrared portion of the remote control should point to the remote sensor of the projector for proper remote control operation. The range of the remote sensor is 18'±5% feet with a 30±10% degree range. 1RWLFH Do not drop or expose the remote control to physical impact. Do not get the remote control wet or place it on wet objects. Remove the batteries from the remote control and store them in a safe place if you will not be using the remote control for an extended period.
and move to the next higher or lower item in the menu. -Press these buttons to increase or decrease the sound volume level and directly choose the item in the menu. --/--˖ -Select the channel rapidly. -Call: -Press this button to view the current signal input and current channel number. &KDSWHU %DVLF 2SHUDWLRQ 6HFWLRQ 7XUQLQJ RQ WKH 3URMHFWRU 1. Make sure that power of the projector and all equipment connecting with the projector is not on. 2. Connect a video source to the projector. 3.
6HFWLRQ 7XUQLQJ RII WKH 3URMHFWRU 1. Turn off the power of the video source equipment, which is connected to the projector. 2. Press the POWER button on the projector or STANDBY/ON button on the remote control. 3. The projector lamp will turn off ,the exhaust fan will continue to run for up to 3 minutes in order to cool the projector lamp and extend lamp life. when the exhaust fan turns off it is safe to remove the power cable. 4. Place lens cap over lens.
1RWLFH If the projector distance is out of range, the projector will be not able to focus. If it is hard to get correct focus, please confirm the distance of projector from the screen. &KDSWHU $GYDQFH 2SHUDWLRQ 1RWLFH Under the situation of menu off, Press the “PC/AV” button of projector or remote control to choose the signal of one of the AV /S-VIDEO /YPbPr /VGA /HDMI . 6HFWLRQ ,QSXW 0HQX Signal: press “ PC/AV ” button to get “PROGRAM” menu.
5. Press [ĺ] button or [ĸ] button, adjust picture’s contrast. 6. Press [MENU] button twice to turn back to “menu function window” 6HFWLRQ %ULJKWQHVV Operation 1. Press “MENU” button on the control board, it will show “menu function window” on the screen. 2. Press [Ĺ] button or [Ļ] button, move cursor to “Picture”. 3. Press [ĺ] button to enter “Picture” menu function. 4. Press [Ĺ] button or [Ļ] button, move cursor to “BRIGHTNESS”. 5. Press [ĺ] button or [ĸ] button, adjust picture’s brightness. 6.
6HFWLRQ 6KDUSQHVV Operation 1. Press “MENU” button on the control board, it will show “menu function window” on the screen. 2. Press [Ĺ] button or [Ļ] button, move cursor to “Picture”. 3. Press [ĺ] button to enter “picture” menu function. 4. Press [Ĺ] button or [Ļ] button, move cursor to “SHARPNESS”. 5. Press [ĺ] button or [ĸ] button, adjust picture’s sharpness. 6. Press [MENU] button twice to turn back to “menu function window” 6HFWLRQ /DQJXDJH Operation 1.
3. Press [Ĺ] button or [Ļ] button, move cursor to “PICTURE SWAP” 4. Press [ĺ] button or [ĸ] button, choose appointed function. 5. Press [MENU] button twice to turn back to “menu function window”. 6HFWLRQ 5HVHW WR 'HIDXOW 6HWWLQJV Operation 1. Press “MENU” button on the control board, it will show “menu function window” on the screen. 2. Press [ĺ] button to enter “FUNCTION” menu function. 3. Press [Ĺ] button or [Ļ] button, move cursor to “MEMORY RECALL” 4.
6HFWLRQ =RRP This function can adjust the size of the image “Zoom” menu is divided 9 grades, you can choose the right grade to gain the best size (The grade 9 is 16:9 screen). Operation 1. Press “MENU” button on the control board, it will show “menu function window” on the screen. 2. Press [ĺ] button to enter “FUNCTION” menu function. 3. Press [Ĺ] button or [Ļ] button, move cursor to “ZOOM”, 4. Press [ĺ] button or [ĸ] button, choose ZOOM ratio. 5.
3URMHFWRU FDQ QRW SURMHFW VKRZ VLJQDO z Please verify that the image source is working. z Please check the cable between signal source and projector is connected or not. z Verify the Input settings match signal of the input port. %OXUU\ LPDJH z Adjust the focus if image is blurry. z The projection angle is too large or distance is too long. z Inspect lens for dust or debris. 4. 7KH LPDJH LV WRR ELJ RU WRR VPDOO. z Verify source resolution.
'LVWLQJXLVK WKH LQGLFDWRU OLJKW &RQWHQW 3RZHU /LJKW %ULJKW UHG Power on and is on working No image, no signal, need switch the signal. 5HG Alarm signal (indicate it will be power off), turn off after power off. Turn on it when it gets cool.
7LPH RI UHSODFHPHQW This product is not designed for continuous use. In the case of continuous use, the lamp’s lifetime will shorten. Please replace the lamp when you meet these problems. z The lamp burn out, but other parts are normal. z The image becomes darker or unclear. 1RWH z If above phenomenon has occurred, we suggest you replace the old lamp as soon as possible. 5HSODFHPHQW Operation: 1.
6HFWLRQ 6SHFLILFDWLRQV subjec to change without notice. 1RWLFH The specifications are subject ,WHP 6SHFLILFDWLRQ 6 3URGXFW 1DPH /LTXLG &U\VWDO 3DQHO 6L]H 7” (Diag) 'ULYH 6\VWHP TFT LCD $VSHFW 4 : 3 or 16 : 9 5HVROXWLRQ HD 1080P; 1080i; 720P; 720i; 480P; 480i /HQV Manual Focus Focus Adjustable /DPS LED &RQWUDVW 1,000:1 %ULJKWQHVV 1700 ANSI Lumens &RORU 'HSWK TrueColor 16.