User manual

ManualsBrandsPyle ManualsCD-playersPDCD204

PDCD204

User Manual

www.pyleaudio.com

1. Intended use

The Pyle Pro PDCD204”is a semi-professional CD player. It used to play standard audio CDs. This

appliance is intended for operation at home and in semi-professional environments.

The low-level audio output signal must be transmitted to an external amplifier (which might be used

together with a mixer or pre-amplifier) for amplification. The appliance should not be connected directly to

loud-speakers.

The CD player consists of a control unit and a dual disc drive. Both units may only be operated together.

Any other use than that described above can result in damage to the product, involving such hazards as

short-circuits, fire and electrocution. No part of the product may be modified or retrofitted and the housing

may not be opened!

The safety instructions must be observed at all times.

2. Equipment features

 Dual-CD-disc drive

 Remote control unit

 8×over-sampling,1 bit D/A converter

 Jog shuttle wheel

 Separate track skip and search buttons

 AUTOCUE function

 Installation possible in a 19” rack system

 Pitch speed control of +/-4%,+/-8%,+/-16%

 LOOP function(playback loop)

 RELAY function(automatic switchover between the two CD drives)

 Frame-precise search(frame=smallest possible scanning unit of the CD player)

 Analogue audio output

3. Scope of delivery

 Control unit

 Drive unit

 2×stereo cinch cables

 1×system connection cable

 Power cable

 Operating instructions

Summary of content (9 pages)

PAGE 1
. Intended use The Pyle Pro PDCD204”is a semi-professional CD player. It used to play standard audio CDs. This appliance is intended for operation at home and in semi-professional environments. The low-level audio output signal must be transmitted to an external amplifier (which might be used together with a mixer or pre-amplifier) for amplification. The appliance should not be connected directly to loud-speakers. The CD player consists of a control unit and a dual disc drive.
PAGE 2
4. Table of contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 6. Safety instructions and danger warnings Introduction.........................................................................................................................................1 Intended use…………………………………………………………………………………………………..2 Equipment features.............................................................................................................................2 Scope of delivery.......................
PAGE 3
7. Connection elements and controls Do not leave the appliance unattended while operating it.  Never place the appliance on an unstable or movable surface. Persons could be injured or the appliance damaged by it falling down.  When using a rack, make sure it is in a stable position and is transported securely. Installation on uneven, slanted surfaces or stopping the rack abruptly during transport can result in the rack overturning or appliances falling from or out of the rack and injuring people.
PAGE 4
function can be found under “Playback loop (LOOP function)”. RELAY function is activated. A detailed description of the RELAY function can be found under “Relay operation”. (5) OPEN/CLOSE button You can open and close the respective CD compartment with this button. (13) PITCH button This button is used to activate the “PITCH slide control” (3) function. The LED above the button goes on whenever the PITCH function is switched on.
PAGE 5
Drive unit LC display (20) CD compartment 2 This is the compartment (disc 2 drive) in which the CD is placed. (21) OPEN/CLOSE button for CD compartment 2 You can open and close the CD compartment of the DISC 2 drive with this button. The CD compartment cannot be opened with the CD player in playback mode. (A) – (D) Track, minutes, seconds, frame display and display of additional information The current CD data, such as position and time, is displayed here.
PAGE 6
Make sure the connection cable is not being squeezed or damaged by sharp edges. Always lay the cables in such a way that no-one can stumble over them or become entangled in them. There is risk of injury! Make sure you avoid direct, intensive sunlight, vibrations, dust, heat, cold and moisture when selecting the location of the appliance.
PAGE 7
Only insert CDs, and only one CD at a time in each CD tray. Never interfere with the motor driven movements of the CD drive tray. Do not push the CD compartment closed since this would damage the mechanics and result in malfunctions. Close the drive tray by pressing the OPEN/CLOSE button again. The appliance reads in the CD (“READ” is displayed). The total amount of tracks and the total CD playing time is briefly displayed on the LC display.
PAGE 8
briefly. The CUE mark was set where the playback was started. 3. If you now press the CUE button, the CD player return to the CUE mark and switches to pause mode. The red LED next to the CUE button goes on. Checking the CUE mark: Press the CUE button and hold it down in CUE mode (red LED next to the CUE button goes on). The CD is played as long as you hold down the CUE button. The CD player returns to the CUE mark and switches to pause mode after letting go of the button.
PAGE 9
12. Troubleshooting 13. Useful notes on handing CDs By purchasing the “Pyle Pro PDCD204 dual CD player”, you have acquired a safe, state-of –the art product. Problems and malfunctions can occur nevertheless. We would therefore like to show you how to eliminate certain malfunctions yourself.    Observe the safety instructions by all means!  Problem Cause Solution No display after Switching on the on/off switch.