PLCD22MRP OWNER'S MANUAL Shipboard Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • Automatically Memory Storing • Direct Track Access • Program CD Tracks • Electronic Shockproof (ESP) Function www.pyleaudio.
CONTENTS Installation.....................................3 Take out screw before installation ..3 Installing the unit ..........................3 Wiring Connection ........................4 Operation.......................................5 Location of keys .............................5 Control & function keys ..................6 Installation hardware ......................8 Switching on/off the unit ..............10 Display the disc slot .....................10 Sound adjustment ........................
INSTALLATION 3. Use the glue paper to stick the two mounting bracket to the back of the dashboard. The screw holes of the brackets must respectively aim at the mounting holes in order to fix the unit to the dashboard. TAKE OUT SCREW BEFORE INSTALL Before install the unit, please remove the two screws. Take out screw before install.
WIRING CONNECTION (BLACK) WIRING REMOTE CONNECTOR SOCKET (YELLOW) RED Rch (YELLOW) ANTENNA CONNECTOR WHITE Lch AUX IN CABLE FUSE RCA CABLE (GREY) RED Rch WHITE Lch BLUE POWER ANTENNA RED YELLOW BLACK FRONT Lch SPEAKER REAR Lch SPEAKER WHITE GREY WHITE/BLACK GREEN GREY/BLACK VIOLET GREEN/BLACK VIOLET/BLACK 4 FRONT Rch SPEAKER REAR Rch SPEAKER IGNITION SWITCH (ACC+) MEMORY BACK-UP (B+) GROUND (B-)
OPERATION 6 9 15 7 11 16 10 12 17 20 21 8 14 22 When pull open the disc cover: 26 5 5 18 3 23 24 19 2 4 13 25 1
OPERATION CONTROL & FUNCTIONS KEYS This unit is a marine rated wired remote control made using a modified controller or similar layout. It is capable of operation specified functions on the marine AM/FM/CD receiver and the marine AM/FM/Cassette receiver. The body, buttons, controls and display need to be UV and water-resistant. It includes and LCD and an illumination circuit. The flat body should be watertight and the circuit board clear coated.
OPERATION 4 MODE SELECTION button Press the MODE button (4) to step sequentially through the following sources: e.g. radio mode to CD mode (or cassette mode) to AUX in mode. 5 BAND SELECTION button FOR WEATHER BAND VERSION ONLY: Press the BAND button (5) to step sequentially through the following bands: FM1, FM2, AM, WX. 6 TRACK/SEARCH/TUNE buttons • STATION SELECTION (FOR RADIO OPERATION) Press / buttons (6) shortly to activate automatic seek function.
OPERATION INSTALLATION HARDWARE HOLDER BASE REMOTE MOUNTING BRACKET X1 X1 X1 SCREW (ø4X50) NUT X2 X2 INSTALLATION DIAGRAM 1. First insert the hooks on the base into the slots of the holder to install the base to the holder. 2. Select the proper object, then place the remote mounting bracket on the base and let the object go through the base and the mounting bracket.
OPERATION 3. Align the screw holes on the holder with the screw holes on the base and the screw holes on the bracket, then use the two screws (ø4X50) and nuts to fix the bracket, the base and holder to the proper location. 4. Last install the remote control to the holder. See below, align the four hooks on the holder with the four slots on the remote control.
OPERATION Adjust bass level by VOLUME button (11) or VOLUME button (12). Treble Press SEL/MENU button (10) three times. Adjust treble level by VOLUME button (11) or VOLUME button (12). Balance Press SEL/MENU button (10) four times. Adjust sound balance between left and right speakers by VOLUME button (11) or VOLUME button (12). Fader Press SEL/MENU button (10) five times. Adjust sound balance between front and rear speakers by VOLUME button (11) or VOLUME button (12).
OPERATION button (11) or VOLUME button (12) to select USA or European radio frequency spacing. - USA radio spacing is 200k for FM and 10k for AM. This is the default frequency spacing. - European radio spacing is 50k for FM and 9k for AM. CLOCK ON/OFF while power off Hold press SEL/MENU button (10) for several seconds, when BEEP ON/OFF appears, press SEL/MENU button (10) shortly three times to select “clock on/off while power off” mode.
OPERATION select CH1~CH7 directly. of the LCD display backlight. RESET FUNCTION When you pull out the plastic panel covering the CD opening, you will see the reset button (26) is placed above the disc slot (5). It must be activated with either a ballpoint pen or thin metal object. The reset button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display.
OPERATION • REPEAT THE SAME TRACK Hold press RPT button (22) for several seconds to continuously repeat the same track. Press it for several seconds again to stop repeat. CD OPERATION • SWITCHING TO CD MODE If there is no CD inserted in the driver: Gently insert the CD with the printed side uppermost into the CD compartment until you feel some resistance. The CD will be drawn into the driver automatically. CD playback begins.
OPERATION and then press BAND/ENTER button (18) shortly. You can also press number buttons 0~9 (14) can activate DIRECT TRACK ACCESS to select your desired track. for several seconds will exit PGM mode. - When the disc is playing in programmed order, pressing MEM button (20) for several seconds will cancel the all programmed content and “CLR” appears on the display. - If you don’t press MEM button (20) to carry out program setting, then press PGM button (21) for several seconds, “NO-P” will appear.
OPERATION Normal SCAN BAND M1 M2 M3 M4 M5 M6 M7 M8 M9 M0 SELECT VOL UP/DOWN AS/PS In MP3 searching MP3 Searching Mode Select ENTER A, B, C, 1 D, E, F, 2 G, H, I, 3 J, K, L, 4 M, N, O, 5 P, Q, R, 6 S, T, U, 7 V, W, X, 8 Y, Z, SPACE, 9 _,-,+,0 Character shift CHARACTER SELECT (A, B~Z, SPACE, 0~9, _,-,+) Backspace • • • 3. SEARCHING FROM ROOT DIRECTORY Press the MP3 button (13) three times, the unit searches file or directory from root directory by VOLUME / buttons (11&12).
OPERATION Note: A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction. 3. Dirt, dust, scratches and warping discs will cause misoperation. B. Notes on CD-Rs (recordable CDs)/ CD-RWs (rewritable CDs): 1.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 178 (D) x 50 (H) mm : : : : ± 10 dB ± 10 dB 4 x 50 Watts 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 60 dB : More than 50 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The ignition switch is not on. If the power supply is connected to the accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
