2-DIN TFT-LCD Monitor with TV/Radio tuner PL2DNTV7 Owner’s manual Please read it before using this equipment. www.pyleaudio.
CONTENTS Welcome ………………………………………………………………………………… Features …………………………………………………………………………………. General Specifications …………………………………………………………………. Operating Instructions…………………………………………………………………… Safety Precautions ……………………………………………………………………… Display care & cleaning…………………………………………………………………. Remote control button function………………………………………………………… Using remote control…………………………………………………………………….. Front panel Button control………………………………………………………………. Basic operation…………………………………………………………………………...
WELCOME Thank you for purchasing the TFT-LCD wide screen MONITOR. We are grateful for your support. Please read this user’s manual in its entirety before operating the unit. After reading this manual, be sure to keep it in a handy place for future reference. Check the contents of the enclosed warranty card and keep it carefully with this manual.
2. Keep this manual handy for future reference. 3. Pay close attention to all warnings in this manual and follow the instructions carefully. 4. Never allow others to use the system until they have read and understood the operation instructions. SAFETY PRECAUTIONS 1.The unit is designed for using in DC12V, negative ground battery. 2. Do not disassemble or alter the unit in any way. Failure to do so can cause damage to the unit and invalidate your warranty. 3.
CAUTION! The material of display area is made by glass with a protector film attached on it. Do not use hard or sharp objects to strike or scratch the surface of the display area. Otherwise it may cause the picture distorted or have scars forever. Remote Control Button Functions 1. Power Turn on or off this unit. 2. Setup (1) DVD/CD changer mode DVD built-in functions menu (refer to SANYO DVD/CD changer Specification) 3. Up/Down (1) DVD changer mode It is the up/down button under Setup/Menu status.
7. Scan /RDM (1) DVD/CD changer mode Press this button to switch scan on/off, Press and hold to switch random on/off. (2) Radio mode Press this button to scan any available frequency and play each one in 5 seconds. *During playing, will play the current frequency if you press this button again; if press other button, will stop this function and play the frequency at beginning of scan. *During scanning, will stop scanning function and play the frequency at beginning of scan. 8.
(2) Radio mode To switch the band in the follows order: FM1 > FM2 > FM3 > MW1 > MW2 press and hold this button to automatically search all stations and store the stations on band FM3 or MW2. 17. Audio CH Select Tone: JAZZ-ROCK-CLASSIC-POP-VOCAL-FLAT-EQ OFF. 18. VOL+ / To increase volume or reduce volume. 19. PBC/LOC (1) CDC mode To select play mode: PBC on/PCB off. (2) Radio mode As PS function, to scan all pre-set station of the current band (M1~M6, step: 5seconds). 20. Stop (1) CDC mode To stop playback.
27. RPT Under DVD mode, allows the user to repeat playback: repeat mode: disc, track/chapter 28. Angle + / It is not available. USING REMOTE CONTROL Aim the IR remote control directly at the unit, or video source with an IR input. Tips: − Maximum IR distance is 3 meters from the sensor. − Direct sunlight or very bright light reduces sensitivity to the IR remote signal commands. Make sure the monitor is not located in direct sunlight.
Front panel Button control 1. Remote sensor 2. Power ON/OFF ( ) 3. Mode 4. Next/Down ( ) 5. Previous/ UP ( 6. Play / Pause ( ) ) 7. CDC 8. Menu ( ) 9. Volume +/- or adjustment 1) Remote sensor For remote control. 2) Power on/off Press this power switch, the LCD monitor will turn on. Press again; the monitor will turn to “Mute on/off” mode. Press and hold for 3 seconds, the monitor will turn off. 3) Mode Select the input signal source. Radio > TV > DVD >AUX IN >RGB IN > Radio 4) Next / Down ( ) 1.
2.Press this button to select the next track/chapter when playing disc under DVD mode, and hold to fast forward until you release it. 3.To select the Next preset station under Radio mode. 4.To fine the current program under TV mode. 5) Previous / UP ( ) 1.Press this button to select the item up under menu state. 2.Press this button to select the previous track/chapter when playing disc under DVD mode, and hold to fast backward until you release it. 3.To select the previous preset station under Radio mode.
Basic Operation System adjustment Press [MODE] to change the mode from AUX IN, RGB IN, REAR VIEW, RADIO MODE, TV MODE and DVD MODE. AUX IN It will display “NO SIGNAL” when there is no AUX in. RGB IN It will display “NO SIGNAL” when there is no RGB in. REAR VIEW It will display “NO SIGNAL” when there is no rear view in. RADIO MODE When you enter radio mode, it will display as below: RADIO BAND RREQ CHANNEL PS PTY TA/AF/PTY/REG/EON INFORMATION FM1 87.
DISP TIME --------------OFF ADJ TIME ---------------00:25 RADIO AREA ----------EUROPE TV SYSTEM ------------C.C.I.R EXIT And then, press [ ] again; it will display another page as below: RDS TA/TP ------------------OFF RDS AF -----------------------OFF RDS PTY ---------------------OFF SEARCH PTY -----------------NEWS RDS REG--------------------OFF RDS EON--------------------ON EXIT You can adjust the values by pressing [ ] and [ ] as below in case of entering the related page.
TV MODE Select stations Press and hold [ ] or [ ] for 3 seconds to automatically search stations and it will automatically store the stations of strongest signal in related band; or press and hold [ ] for 3 seconds to search stations automatically and then it will automatically store stations of strongest signal. If you want to stop searching, press and hold [ ] for 3 seconds again. Select the display mode FULL or NORMAL with menu.
EQ adjustment Press [ ] repeatedly when there are some pictures on display to change from Volume, TA VOL, Bass, Treble, Balance or Fader. And then press [+] and [-] to adjust the value of related EQ option above. CDC MODE When you select CDC mode, it will display as below: CDC DISC No.: TRACK No.
Connection Layout Connect to your car 1. To prevent short circuits, remove the key from the ignition and disconnected the terminal of the battery. 2. Connect the wiring harness cables in the following order: ground wire, battery wire, ignition wire. Connect the input and output cable correctly to each unit. 3. Connect the wiring harness connector to the monitor unit.
4. Reconnect the terminal of the battery of procedure. Notes ● If your vehicle ignition does not come with an ACC position, connect the ignition cables to a power source that can be turned on and turned off with the ignition key. If you connect the ignition cable to a power source that receives a constant voltage supply, as with battery cable, the battery may be overloaded.
