Specifications

G01 OEM Module
With WiFi, BLE and cellular LTE-CAT M1/NB1, the G01 OEM
Module is the latest Pycom triple-bearer MicroPython enabled
micro controller on the market today – the perfect enterprise
grade IoT plaorm for your connected things. Create and
connect your things everywhere, fast.
- Espressif ESP32 SoC
- Dual processor + WiFi radio System on Chip.
- Network processor handles the WiFi connecvity and the IPv6
stack
- Main processor is enrely free to run the user applicaon
- An extra ULP-coprocessor that can monitor GPIOs, the ADC
channels and control most of the internal peripherals during
deep-sleep mode while only consuming 25uA
- Powerful CPU
- 1KM Wi Range
- MicroPython enabled
- Fits in a standard breadboard (with headers)
- Ultra-low power usage: a fracon compared to other connected
micro controllers
G01 Features
Use the Pymakr IDE
Super easy code editor to write your Python scripts
Easy Upload
Upload your scripts, and any other les you want to the G01 via
the FTP server
Locally or remotely
Reset the G01 (you can do it locally, or remotely via Telnet)
Mechanical
Processing
Hash / encryption
SHA, MD5, DES, AES
WiFi Networking
802.11b/g/n 16mbps
Bluetooth
Low energy and classic
RTC
Running at 32KHz
- 2 x UART, 2 x SPI, I2C, I2S, micro SD card
- Analog channels: 8x12 bit ADCs, 2x8 bit DAC
- Timers: 2x64 bit with PWM with up to 16 channels
- DMA on all peripherals
- Voltage Input: 3.3V regulated
Interfaces
Power
Size: 40mm x 16mm x 2.7mm
Security & Certications
- SSL/TLS support up to 1.2
- WPA Enterprise security
- AES encrypon engine
Memory
- RAM: 4MB
- Flash Memory: 8MB
- GPIO: Up to 22
- Hardware oang point
acceleraon
- Python mul-threading
- 34 bands supported from 699Mhz to 2690Mhz (Total world-
wide support)
LTE-M Operating Frequencies
- One single chip for both CAT M1 and NB1 (yes, only one chip)
- 3GPP release 13 LTE Advanced Pro
- Supports narrowband LTE UE categories M1/NB1
- Integrated baseband, RF, RAM memory and power
management
- Reduced Tx power class opon
- Peak power esmaons: TX current = 420mA peak @1.5Wa
RX current = 330mA peak @1.2Wa
- Data rates:
- 300 kbps DL
- 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD)
- 40 kbps DL
- 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD)
LTE-M Specication
ESP32 Dual Core
Microcontroller and
WiFi/Bluetooth 4.2
radio
8MB ash memory
LTE CAT M1 / NB1
transceiver
Distributed and manufactured by Pycom Ltd.
Registered oce:
High Point, 9 Sydenham Road, Guildford, Surrey GU1 3RX, UK
Copyright © 2017 by Pycom Ltd. All rights reserved. No part of this
document may be reproduced, distributed, or transmied in any form or
by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior wrien permission of Pycom Ltd,
except in the case of brief quotaons embodied in crical reviews and
certain other noncommercial uses permied by copyright law.
To order contact [e-mail]