User manual BMP40 audac.
ADDITIONAL INFORMATION This manual is put together with much care, and is as complete as could be on the publication date. However, updates on the specifications, functionality or software may have occurred since publication. To obtain the latest version of both manual and software, please visit the Audac website @ www.audac.eu.
Table of contents Introduction 04 SourceCon™ Bluetooth receiver module ����������������������������������������������������������������������������������������� 04 Precautions 06 Chapter 1 08 Connections and connectors ����������������������������������������������������������������������������������������������������������� 08 Chapter 2 09 Overview BMP40 ������������������������������������������������������������������������������������������������������������������������������� 09 C
Introduction SourceCon™ Bluetooth receiver module The BMP40 is a professional Bluetooth receiver module featuring SourceCon™ modular technology. This unique technology guarantees true plug & play implementation to any compatible device. When inserted to a supporting slot, the module is instantly installed, discovered and ready for operation without requiring any additional internal wiring or complex configuration.
POWER SUPPLY AND POWER CORD REQUIREMENTS Power supply class I grounding requirements: For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide adequate fault protection.
Precautions READ FOLLOWING INSTRUCTIONS FOR YOUR OWN SAFETY ALWAYS KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. NEVER THROW THEM AWAY ALWAYS HANDLE THIS UNIT WITH CARE HEED ALL WARNINGS AND FOLLOW ALL INSTRUCTIONS AVOID ELECTROSTATIC DISCHARGE BY TOUCHING GROUNDED POINT BEFORE REMOVING THE MODULES FROM THEIR PROTECTIVE BAG AVOID TOUCHING OF THE COMPONENTS ON THE CIRCUIT BOARD DIRECTLY NEVER EXPOSE THIS EQUIPMENT TO RAIN, MOISTURE, ANY DRIPPING OR SPLASHING LIQUID.
CAUTION - SERVICING This product contains no user serviceable parts. Refer all servicing to qualified service personnel.
Chapter 1 Connections and connectors CONNECTION STANDARDS The in- and output connections for AUDAC audio equipment are performed according to international wiring standards for professional audio equipment 3-Pin Terminal block: For unbalanced line input connections Signal - (XLR Pin 3) Left: Signal + (XLR Pin 2) Center: Ground (XLR Pin 1) Right: For balanced signal input connections + 08 For balanced signal input connections + BMP44 - User manual
Chapter 2 Overview BMP40 The BMP40 is a SourceCon™ compatible module featuring an (internal) board-edge connector which carries all signals for getting it connected to any supporting main unit. All external in & output connections shall be made using the available connectors on the panel. 1) Balanced stereo line output: The balanced stereo line output is implemented using two 3-pin terminal block connectors. The audio output available on this connector allows it to be fed to any amplifier or pre-amplifier.
Chapter 3 Using the BMP40 Since the BMP40 is a SourceCon™ module, it can be combined with a variation of supporting main units. The operation and configuration interface might be different of the unit where installed, however the offered functionality is identical. Some devices will support control and configuration through a front panel graphical control interface on a display, while others are also supporting web-control.
Player mode In this screen, all available media information about the currently playing files is shown including track, artist or any other information, while previous and next audio track selection can be done. Bluetooth receiver Track name Note that the displayed information in this screen depends on the supported functions of the connected transmitter.
Settings screen The settings menu for BMP40 can be loaded by pressing the rotary selection dial. Output gain: The gain can be adjusted within a range of +8 dB and -82 dB, allowing optimization of the output level according to the input sensitivity of the connected amplifier or pre-amplifier. For adjusting the output gain, rotate the function dial until ‘Gain’ is highlighted and press it for proceeding to the gain settings.
Chapter 4 Installing the BMP40 CAUTION Before installing the BMP40 to any SourceCon™ compatible device, make sure the power is switched off. Malfunctions or electrical shocks may occur otherwise. Step 1: Make sure that the slot whereto the module should be installed is open and ready for installation. Depending of the main unit, some module slots will be covered by blind panels when delivered. The corresponding blind panels should be removed by releasing the screws on both ends.
Step 4: Some resistance might occur when the module’s board edge connector reaches the connection counterpart on the main board. Gently push the module all the way into the slot to ensure that the contacts are correctly inserted. The module is well inserted when its connection panel touches the metal chassis of the main device where inserted to. Step 5: Fasten the module into the slot using the included screws. Be aware that damage or malfunctions may occur if the module is not correctly fastened.
Technical specifications Connection SourceCon™ interface card slot Input SMA-type male antenna connection (50 Ω) Output Balanced stereo line output (2 x 3-pin Euro Terminal Block ~ 3.81 mm) Output level +8 dB ~ -82 dB (Software configurable) Bluetooth receiver Bluetooth spec V4.1 Class 2 output power Power consumption 0.5 Watt Dimensions (W x H x D) 87 x 34.5 x 114 mm Weight 0.075 Kg Packaging Carton box Shipping weight & Volume 1.08 Kg - 0.028 Cbm Accessoried included 2.
Caution: This device complies with Part 15 of the FCC rules and Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment.