Fax Modem Quick Installation Guide Ver.
FCC Compliance To comply with the applicable sections of FCC Rules and Regulations, Parts 68 and 15, please follow these instructions: Do not connect your modem to a party line or to a coin-operated telephone. If your modem should cause a problem on the telephone line, it should be disconnected from the line until it can be determined whether the modem or another device on the phone line caused the problem. Only the manufacturer can make repairs to the modem.
FCC Part 15 Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. ! Caution Any changes or modifications not expressly approved by the grantee of this device could void the user authority to operate the equipment. FCC Part 68 Notice This equipment complies with Part 68 of the FCC rules.
If the telephone company suspects a problem with your telephone line is related to an add-on electronic device, such as your modem, they have the right to temporarily suspend your service. It is your responsibility to remove from the telephone line any malfunctioning electronic communications equipment to avoid damage to the telephone system. If your equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance.
Table of Contents Chapter 1 Introduction Features System Requirements Package Checklist 11 12 12 Chapter 2 Installation Hardware Installation 13 Installation Procedures for Windows NT 4.
Chapter 1 Introduction The Voice/Fax/Data PCI Modem connects your computer to Internet, all kinds of BBS, and other fax modems. This manual describes the features, installation procedures and AT commands. To Phone To Line Phone : Phone jack Line : Telephone line jack Features This modem supports the following communication standards. ITU-T is known as CCITT. Data Fax ITU-T V.90. ITU-T V.34, V.32bis, V.32, V.22bis, V.21, V.22. Bell 103 & 212A. V.42bis & MNP 5 (Data compression). V.
Chapter 1 Voice Voice/Audio mode. System Requirements Windows NT 4.0, Windows 95, Windows 98, Windows 2000. Package Checklist The package contains the following items: One fax modem. One piece of phone cable. One CD. The fax modem Quick Installation Guide. If any of these items is missing or damaged, please contact your dealer or sales representative for assistance.
Chapter 2 Installations This chapter describes how to install and power on you fax modem. Hardware Installation 1. Make sure that your computer is switched off. Unplug the power cord from the wall socket. Also turn off all other peripherals you may have attached to your computer. 2. Select a free PCI slot. Remove the cover from the slot. Keep the screw. You will be using it in the next step. 3. Carefully slide the internal modem into the chosen slot. Press firmly on the top of the modem to seat it.
Chapter 2 5. If you desire, you could connect your phone to the modem’s phone jack. 6. Turn on your computer. Installation Procedures for Windows NT4.0 1. Please put the CD into your CD-ROM, then select DriverÆWINNT4, click Setup. A dialog box with ESS Configuration appear, please select the proper Com port, then click OK. 2. Please click OK. 3. Select the modem item from the Control Panel, then click Do not delect my modem, I will Pick up from the list . 4.
Chapter 2 Installation Procedures for Windows 98 1. Once you have completed the hardware installation, power on your computer. When running Win98, your system will detect a new device and the following message will appear. click Next. Ñ 2. Select the “ Search for the best driver for your device (Recommended) ” option, then click Next.
Chapter 2 3. Place the CD containing driver for Win98 into your CD ROM drive. Specify the location of the modem driver, e.g., D:\Drivers\WIN9X. then click Next.. Ñ 4. Click Next.. Ñ 5. Windows Will locate your driver. click Next.
Chapter 2 Ñ 6. The installation has been completed click finish. Ñ Installation Procedures for Windows 2000 1. Once you have completed the hardware installation, power on your computer. When running WIN2000, your system will detect a new device. click Next. 2. Select the “Search for a suituble driver for my your device” (recommended) option, then click Next.
Chapter 2 3. Place the CD containing driver for Win 2000 into your CD ROM drive. Select the “specify a location”, then click Next. 4 . Browse the proper location of the driver path, e.g., D:\Driver\WIN2000, then cilck Next. 5 . Click Next. 6 . Please read the Digital Signature, then click Yes. 7 . To complete the installation, click Finish. Commands Most people use the communication software programs to tell modems what to do. Therefore, you may not use the commands in this chapter.
