FEDERAL COMMUNICATIONS COMMISSION NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Introduction Introduction Fax e FAX) eo FAX) s FAX) « Audiological mode s Full-Duplex speakerphone « AudioSpan(Simultaneous Audio/Voice/Data; SAD) 2. Internal Modem Card(bracket) = NOTE = PHONE: Phone Jack. aT LINE: Telephone fine Jack. Ba MIC: Microphone Jack. SPK: Speaker(for Stereo only) jack. weedy rly Features This modem supports tt x following communication standards: Note: IT-T Is known as CIT. Data o IT-T 56Kbps Modem only) o Rockwell K56flex(For 56Kbps Modem only) e IT-T V.34, V.32bls, V.32, V.
Chapter 2 Installations This chapter describes the steps how to Install and power on your fax made. B Note: Do not power aa our modem before you finishing the following Installation. 1. Installing External Modem If your modem Is external ane, please refer to following procedure: + external Moderation: « external Voice/Fax/Modem Step |: Plug the male end of the cable Into the connector marked on the back of the modem.
Installations 3. Installation Procedure for Windows 95 @ Note: Win ’95 div eis on the CD root directory. 3-1. For Plug and Play User Step 1: Set jumpers for PnP iv ode. Step 2: Turn on the PLUG AND PLAY feature on your system BIOS for initializing the PnP device.
Read Selected S-Register. This command reads and displays the selected S-Register. An S-Register an be selected by using the Tans command. Belittle-T answer sequence. Select V.22 connection at | 200bps. Select Bell 212A connection at 1200bps. Carrier “col Rewrite CK message. Dial MDT digits 0 to 9. The ‘star’ digit (tone dialing only}. The 'gate’ digit {tone dialing only). THEFT digits A,B,C, and D. Some countries may prohibit sending of these digits during dialing.
Commands fn FO afi “Gn “@Go aG aG2 Kn aKO aK aK4 aks am2 M3 aQn 2Q0 HQ4 2Q5 ab &Rn SRO aR1 Load Factory Configuration (Profile) Restore factory configuration 0. Restore factory configuration 1. Select Cunard Tone Disable ward tone. (for USA area) able guard tone, Select 1300Hz guard tone. Flow Control Disable flow control. Enable RESTRICTS flow control. {Default for data modem modes} Enable XON/XOFFE flow control. Enable transparent XON/XQFF flow control.
Commands For example: where: i : select V.34 1 : auto mode enable 300 : terminate data speed 300 bps 33,600 maturate data speed 33,600 bps If you want to select V.34 28800 bps only, please Insure -SSE=n Enable ‘Disable DVD (optional) This con wand enables or disables DVD {Digital DVD. The syntax Is where nis a number from Oto 1. -SSE=0 Disable DVD. -SSE=1 Enable DVD.
CARRIER 1200 CARRIER 7400 CARRIES. 4800 CARRIER 7200 CARRIER 9600 CARRIER 12000 CARRIER 14400 CARRIER 16800 CARRIER 19200 CARRIER 21600 CARRIER 28800 CONNECT 16800 CON JET 21600 CONNECT 24000 CONNECT 26400 CONNECT 28800 COMPRESSION: CLASS S COMPRESSION: V.42bis COMPRESSION: NONE PROTOCOL: NON PROTOCOL: LAMP 26 Commands Carrier rate of 1200bps. Carrier rate of 2400bps. Carrier rate of 4800bps. Carrier rate of 7200bps. Cartier rate of 12000bps. Carrier rate of 14400bps. Carrier rate of 16800bps.
_ Commands 4533 bps. 190 CONNECT 46667 Connection made at 46667bps. 173 CONNECT 48000 Connection made at 48000bps. 191 CONNECT 49333 Connection made at 4933 bps. 192 CONNECT 50667 Connection made at 50667bps. 175 CONNECT 52000 Connection made at 52000bps. 193 CONNECT Connection made at 194 CONNECT 54667 Connection made at 5466 bps. 177 CONNECT 56000 Connection made at 56000bps.
S-Register Definitions S-Register Definitions S86 Sot 595 disconnecting command is received. Range: 0-255 Default: 20 (seconds) Call Failure Reason Code 0 Normal disconnect, no error occurred. 4 Loss of carrier. 5 V.42 negotiation failed to detect an error-correction modem at the other end. é No response to complete negotiation. 9 The modem could not find a common protocol. 12 Normal disconnect initiated by the remote modem. 13 Remote modem does not respond after 10 re-transmissions of the same message.
Troubleshooting Make sure that your software and modem are set to the same flow control setting and to either a fixed or variable serial port rate, Type the following command to Toad the template that enable hardware flow control as well as other optimal settings. AT HF view > Disable any Terr caste and Stay Resident {TSR) programs running in the by ground. Q. If your communications software is reporting many Cyclic Redundancy check (CRC) error and low characters per second (CPS).