WHd030-V2 User Manual | Benutzerhandbuch
Safety Warnings • To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or moisture. Do not use the product close to a bath, swimming pool etc. • Do not expose the components of your sytems to extremely high temperatures or bright light sources. • In case of improper usage or if you have altered and repaired the product yourself, all guarantees expire.
. Installation 4. Usage 3.1 The PureLink WHD030-V2 Transmitter (TX) 4.1 Switch the PureLink WHD030-V2 ON 1. Once both power adapters have been inserted into the socket, the PureLink WHD030-V2 transmitter and receiver will switch on automatically. 2. While warming up, both power LEDs will flash blue until the signal connection between the transmitter and receiver has been established. It takes about 80 seconds for the system to start up. 3.
5. Frequently asked questions No connection If the PureLink WHD030-V2 is not able to make a stable connection for 80 seconds during startup, the PureLink WHD030-V2 Receiver is probably outside the range of the PureLink WHD030-V2 Transmitter. Place them closer to each other (a minimum distance of 1 meters apart) and check whether the connection can be made. No signal available from chosen source The PureLink WHD030-V2 does not recognize an input signal on the selected SOURCE.
Sicherheitshinweise 3. Installation • Um Kurzschlüssen vorzubeugen, nutzen Sie dieses Produkt bitte ausschließlich innerhalb geschlossener und trockener Räume. Nicht in der Nähe eines Bades, Schwimmbades usw. verwenden. 3.1 Der PureLink WHD030-V2 Sender (TX) • Setzen Sie die Komponenten Ihres Systems nicht extrem hohen Temperaturen oder starken Lichtquellen aus. • Bei einer zweckwidrigen Verwendung, selbst getätigten Veränderungen oder selbst ausgeführten Reparaturen verfallen alle Garantieansprüche.
4. Anwendung 5. Häufig gestellte fragen 4.1 Schalten Sie den PureLink WHD030-V2 ein Keine Verbindung 1. Nachdem Sie den Netzadapter an die Steckdose angeschlossen haben, schalten sich der PureLink WHD030-V2 Sender und Empfänger automatisch ein. Wenn der PureLink WHD030-V2 nach dem Einschalten innerhalb von 80 Sekunden keine stabile Verbindung herstellen kann, befindet sich der WHD030-V2 Empfänger wahrscheinlich außer Reichweite des Senders.
Sender (TX) HDMI Eingang 1x HDMI-A (19-pin Buchse) Maße 30 x 82.2 x 17.5 mm Appendix - supported Resolutions ANHANG - Unterstützte Auflösungen Video Format Timings Videoformat Empfänger (RX) HDMI Ausgang 1x HDMI-A (19-pin Buchse) Maße 194.8 x 146.8 x 31 mm Spezifikationen 100-240VAC @ 50-60Hz, 5VDC 1.5A Die hier enthaltenen Angaben und Spezifikationen können ohne vorherige Mitteilung geändert werden. 640x480p @ 59.
PureLink GmbH Von-Liebig-Straße 10 D - 48432 Rheine Germany Telefon: 0049 (0)5971-800 299 -0 Fax: 0049 (0)5971-800 299 -99 E-mail: info@purelink.de Internet: www.purelink.de © 2014 PureLink GmbH. All rights reserved. All trade names are registered trademarks of respective manufactures listed. HDMI is a trademark of HDMI Licensing LLC.