KIDS PRO FREESTANDING REFLEX PUNCHING BAG MODEL# 8918PP / PRODUCT MANUAL - VERSION 09.17.02 FOR AGES: WEIGHT LIMIT: TO BUILD: 6+ N/A X 1 TOOLS NEEDED: N/A CUSTOMER SERVICE GQBrands.com • CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: KIDS PRO FREESTANDING REFLEX PUNCHING BAG MODEL# 8918PP To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at At GQBrands®, we want all of our customers to be completely satisfied with their purchase. Take time to review the contents of the product you have just received to make sure that all of the parts are included.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • Adult assembly required. • Always consult a physician before beginning any exercise regimen. • It is only recommended for use by children 6+ years of age. • The product springs back when in use.
PARTS LIST 1- Base 2- Bottom Pole 3- Middle Pole x1 x1 x1 4- Upper Pole 5- Speed Bag x1 x1 7- Cap 6- Adjustable Knob 8- Cap Ring x1 x1 11- Spring Washer 10- Washer x1 x1 x2 12- Hex Screw x2 14- Hand Pump 9- Base Cap 13- Wrench x1 15- Right Glove x1 16- Left Glove x1 x1 x1 4 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 1: Parts: Part 1 (x1) - Base Part 2 (x1) - Bottom Pole Part 9 (x2) - Base Cap Part 10 (x1) - Washer Part 11 (x1) - Spring Washer Part 12 (x1) - Screw Place both Base Caps (2) at the bottom and top middle areas of the Base (1). On the bottom of the base, place the Washer (10), Spring Washer (11), and Screw (12) and install. 2 Once the Screw has been installed, place from the top of the base, the Bottom Pole (2) and secure tightly.
ASSEMBLY INSTRUCTIONS STEP 2: Parts: Part 3 (x1) -Middle Pole Using the Snap and Click button on the bottom pole, push down and slide the Middle Pole so it finds the correct opening. 3 2 6 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 3: Parts: Part 4 (x1) - Upper Pole Part 12 (x1) - Adjustable Knob With the smaller opening facing upwards to install the Speed Bag, slide the Upper Pole (4) to the Middle Pole until you find a proper height size. NOTE: Every indent on the Upper Pole is an appropriate size for the Adjustable Knob to be installed on. Once the right height has been chosen, secure the Adjustable Knob (12).
ASSEMBLY INSTRUCTIONS STEP 4: Parts: Part 5 (x1) - Speed Bag Part 14 (x1) - Hand Pump 14 Find the Speed Bag (5) opening on top of it, and inflate with the Hand Pump (14) until the ball is round and safe to punch. Do not over inflate the Speed Bag, doing so may rupture the Bag and/or may explode during use. 5 NOTE: The Needle of the Hand Pump can be found and stored away when not in use on the handle itself.
ASSEMBLY INSTRUCTIONS STEP 6: It is required that the Base be filled with either sand or water to stabilize and keep it grounded while in use. Locate the opening to the side of the middle Base Cap on the top part of the Base. Fill with your preferred weight method. Sand Water STEP 7: 7 8 MODEL# 9308TS Parts: Part 7 (x1) - Base Cap Part 8 (x1) - Cap Ring Make sure That the Cap Ring (8) is inside the Base Cap (7) to prevent it from bending or releasing from the opening.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.com 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149 10 GQBrands.com CustomerService@GQBrands.