Instructions / Assembly

ManualsBrandsPumpSpy ManualsSmart Energy Management1/2 HP Submersible 12-Volt DC WiFi Connected Battery Backup Sump Pump and Monitoring System

IMPORTANT!

READ ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USING THIS PRODUCT.

Save these instructions for future reference. Failure to read and follow the warnings and instructions

within this instruction manual could result in property damage, serious injury or death.

INSTALLATION AND OPERATING INSTRUCTIONS

ELECTRONICS AND PUMP COMPONENTS ASSEMBLED IN THE USA

MONITORING SOFTWARE AND TECHNOLOGY MADE IN THE USA

12 VDC Sump Pump

System Solid State Pump Controller

Power Supply Requirements 12 VDC

Motor Brushless DC

AMP Rating 18 Amps

Temperature Rating 40°F to 120°F

Discharge 1 1/2” NPT

MAX Flow 3000 GPH

Power Supply Requirements 120 VAC, 60 Hz,

15 AMP

Electrical Ratings 12Amps @ 120 VAC;

18 Amps @ 12 VDC

Relative Humidity 0 to 80%

Storage Temperature 0° to 70°C

Operating Temperature 0° to 50°C

SPECIFICATIONS

PumpSpy

™

PS2000

PumpSpy Technology | support@PumpSpy.com

34000 Lear Industrial Parkway, Avon, OH 44011

PUMP

SPY

The PumpSpy System requires a 12V Deep Cycle Battery (not included), 40 amp/hr

minimum, 75 amp/hr or higher recommended. SLA/AGM Battery strongly recommended.

WIFI CONNECTED BATTERY BACKUP

SUMP PUMP & MONITORING SYSTEM

24/7 AUTOMATED REMOTE SUMP PUMP MONITORING

Summary of content (8 pages)

PAGE 1
PUMP SPY ® WIFI CONNECTED BATTERY BACKUP SUMP PUMP & MONITORING SYSTEM 24/7 AUTOMATED REMOTE SUMP PUMP MONITORING INSTALLATION AND OPERATING INSTRUCTIONS PumpSpy Technology | support@PumpSpy.
PAGE 2
SAFETY FIRST! This instruction manual contains very important information for you to know and understand. This information is provided for your safety and to help prevent equipment problems from occurring. Please observe all safety information labeled danger, warning and caution. WARNING WARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH, SERIOUS INJURY OR MAJOR PROPERTY DAMAGE. RISK OF ELECTRIC SHOCK.
PAGE 3
UNPACKING Inspect this unit before beginning installation. Occasionally, products are damaged during shipment. If the pump or any components are damaged, contact PumpSpy™ at support@pumpspy.com for replacement. The PumpSpy System requires a 12V Deep Cycle Battery with a minimum 40 AMP/HR rating, 75 AMP/HR rating (or higher) recommended. AGM Battery is strongly recommended. INSTALLATION WARNING BEFORE INSTALLING BACKUP PUMP Turn power to main pump off! WARNING! Electric shock hazard.
PAGE 4
METHOD 2 (Connecting to existing discharge line) See Figure 2 If a separate, dedicated discharge is not desired as in Method 1, the Backup Pump can be tied into the main pump’s discharge pipe by installing a “Y” connector. Two check valves will be required. 1. This pump has a 1-1/2 in. NPT discharge. 2. C ut a 3 ft. section of 1-1/2 in. rigid PVC pipe. Glue 1-1/2 in. pipe to a threaded fitting. 3. Screw pipe from step 2 into pump discharge. 4. Place the pump with the 3 ft.
PAGE 5
CONNECTING THE PUMPSPY CONTROLLER 1 2 1. Install the Backup Pump using good plumbing practices. Both the Primary and Backup pumps should set on the bottom of the basin. 2. I nstall the switches for the primary pump and backup pump. The ON level of the lowest backup switch should be approximately 1” - 2” higher than the ON level of the primary sump pump. 3. Connect the Backup Sump Pump to the PumpSpy™ Controller’s white jack. 4.
PAGE 6
CONNECT YOUR SYSTEM TO WIFI AND THE PUMPSPY MONITORING SERVICE Your PumpSpy system, once online, connects to PumpSpy’s Remote Monitoring Service. PumpSpy watches over your system automatically, 24 hours a day. PumpSpy collects operating data on your sump pumps and battery and analyzes this information to make sure your pumps are always in top working condition.
PAGE 7
ADDING YOUR DEVICE MANUALLY If you hare having issues with setting up your PumpSpy device via the app, you can manually set up the device. This process works on all Apple and Android devices. • O n your Apple/Android device, go to Wi-Fi settings and connect to the PumpSpy device’s Wi-Fi network • I f your device warns you that there is no internet connection available, that is normal. Stay connected to the PumpSpy Wi-Fi network.
PAGE 8
LIMITED THREE-YEAR WARRANTY WHAT THIS WARRANTY COVERS When used and maintained in normal use and in accordance with the Installation and Operating Instructions, your PumpSpy™ product is warranted against original defects in material and workmanship for a full three years from date of purchase (the “Warranty Period”).