PEAK PRO INSTRUCTION MANUAL
READ CAREFULLY! Please read the entire instruction booklet before using your device to ensure you’re getting the most out of your Peak Pro. You will avoid damaging your device, or interrupting your experience if you do it now vs. later. See Puffco.com/Support for instructional videos and helpful tips.
THE PUFFCO PEAK PRO This guide will show you how to use your Peak Pro including preparation, cleaning, and app connectivity.
03 WHAT’S INSIDE: E A F B G H C I D A: B: C: D: E: Loading tool Dual Tools (5) AC Adapter USB-C Cable Carb Cap Tether F: Carb Cap* G: Chamber H: Glass* I: Peak Pro Base J: Carrying Case *Each glass piece is hand blown and may vary slightly in size.
04 J
05 WHAT’S NEW: Bluetooth App Enabled USB-C charging Large Capacity Chamber Wireless Charging (Dock sold separately) Intelligent Temperature Control Customizable LED lights
06 QUICK START: 1 Fully charge the device before first use. The lights will pulse white while charging. The Peak Pro Power Dock can wirelessly charge your device. (sold separately) 2 X Fill glass with water just above the air-holes. Do not fill glass while attached to base.
07 3 Align inlet hole on the front of the glass with chamber. Carefully push the front of glass into the base, then push the back down. 4 To unlock / lock the device, hold down the button for 3 seconds.
08 5 Single click to toggle through heat settings. Blue (Low) - Green (Medium) RED (High) - White (Peak) 6 Use loading tool or a Puffco Dual Tool to place contents on the bottom surface of the bowl (not the sides).
09 3 7 Attach tether here Place carb cap on top of chamber. Press down until snug. Use the included carb cap tether to keep it safe during use. 8 4 Double click to initiate heat-up. Press and hold button anytime to exit. Pulsing light indicates heat-up mode is active.
10 9 5 Device will vibrate and lights will flash 3 times when ready. Inhaling gently will produce the best results. *See p. 11 for boost mode. 10 6 Use a cotton swab or Dual Tool to clean the chamber after each use. Wipe gently in a circular motion.
09 11 TEMPERATURE SETTINGS: HOW TO CHOOSE A SETTING 1. Ensure device is on. 2. Click once to cycle through each heat level. 3. Double click to initiate heat-up. COLOR TEMP. NEED TEMPS PEAK - 600 HIGH - 550 MED - 500 LOW - 450 These are the default color and temperature settings. They are further customizable through the app.
HEAT SETTING PROFILES: Each heat setting has an intended purpose and results depending on the experience you’re looking for. There is no wrong answer when selecting a setting, experiment to find what works best for you and your consumption needs. PEAK (ADVANCED) This setting is intended for the user looking for maximum vapor production and the strongest effects. HIGH (STRONG) This setting offers higher vapor production, while maintaining flavor quality.
13 CLEANING: CHAMBER 1. Unscrew the chamber from the base. Do not handle if hot. 2. Light Cleaning: Use a cotton swab to gently remove any residue with 90%+ isopropyl alcohol. 3. Deep Cleaning: Submerge the chamber in 90%+ Iso for 20 minutes. Never use water (iso only). Iso is flammable, let it dry! CLEANING: BASE Preparation: Remove glass and chamber. Gently clean the gold contact points using cotton swabs soaked in iso. Clean the airpath between the chamber and the glass.
14 CLEANING: GLASS Preparation: Carefully remove glass from base. 1. Once removed, submerge in iso. 2. After soaking, remove from iso alcohol and rinse clean with water. (Iso tastes bad, make sure it’s completely removed). Allow glass to thoroughly dry before re-attaching to base. X X - Do not let water seep into bottom chamber of glass. GENERAL WARNINGS: - Do not overfill the chamber. - Do not blow or exhale hard into the glass. This will force water into the base.
15 ADVANCED FEATURES: BOOST MODE: Double click to activate boost mode. This extends the time and/or increases the temperature of your hit. You can continue to boost as needed. By utilizing the app, you can customize the desired time and temperature of your boost. READY MODE (APP): *The Peak Pro Power Dock and mobile app are required to activate ready mode. Once the Peak Pro is paired with a mobile device, enable “Ready Mode” found in the Peak Pro app settings.
APP INTEGRATION: The Peak Pro app integration has a wealth of new features that allow you to customize your experience, unlock special features, and more. 1 Search this link on your phone: App//@puffco.com 2 Starting from the off position hold the button for 6 seconds to sync your Peak Pro with your app.
COMPLIANCE: Puffco Peak Pro FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2.
02 interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interferencve by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.
03 (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d’Innovation, Sciences et Développement économique Canada. (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.” © 2020 Puff Corp.