Pr oduct Name:Pudu Wat ch Model Name:PW1
快速指南 QuickGuide V1.
声明 Copyright © 2019 深圳普渡科技有限公司版权所有,保留所有权利。 未经深圳普渡科技有限公司明确书面许可,任何单位或者个人不得擅自仿制、复制、 誊抄或转译本说明书部分或者全部内容,且不得以营利为目的进行任何方式(电子、 影印、录制等)的传播。本说明书所提到的产品规格和资讯仅供参考,如果内容更 新,恕不另行通知。除非有特殊规定,本说明书仅作为使用指导,所作陈述均不构 成任何形式的担保。
使用者快速指南 目录 产品介绍 1 设备部署 3 售后服务 13
PUDU ROBOTICS 产品介绍 感谢您选择普渡科技产品。 本产品需配合普渡科技好啦机器人与 LoRa 通信调度中控使用。LoRa 呼叫通知手 环(下文简称“手环”)是机器人与 LoRa 通信调度中控(下文简称“中控”)的通 信消息发起与接收终端设备。好啦机器人的整套呼叫业务通信系统基于自组网的 LoRa 通信方案,在整套方案运行期间,手环发起所有任务请求,发送至中控做任 务分配与决策中继,再转接任务至机器人,由机器人返回执行结果至中控,再行返 回执行状态到手环,因此,为避免呼叫系统不稳定,我们建议您在完成设备部署后, 如非必须,不要轻易切断网关的供电,也不要轻易移动网关的位置。 期望好啦机器人可以更好的为您提供服务。 产品特性 产品特性 描述 工作频段 470-510MHz,默认工作频段 490MHz 863-870MHz, 默认工作频段 868MHz(H8) 902-928MHz, 默认工作频段 915MHz(H9) 917-923.5MHz, 默认工作频段 920MHz(H9K) NFC 读写卡 支持 液晶显示 1.
产品特性 产品特性 数量 LoRa 呼叫通知手环(型号 PW1) 1 手环充电座 1 USB-A 充电数据线 1 保修卡 1 用户手册 1 出厂合格证 1 注意:在安装网关之前,请确保 包装盒中应有的配件齐全,如果 发现包装中任何东西缺失或损坏, 请立即联系您的卖家 使用须知 1. 呼叫通知手环既可以表带形式戴在手腕,也可固定在充电座,粘在需呼叫的地方; 2. 手环有一定的防水能力,可以适当沾水,不影响产品性能,但产品不接受任何暴 力形式的冲水或泡水处理,也无法避免在水蒸气环境下的防水; 3. 手环表面有 Led 状态灯,当手环处于呼叫(蓝色),充电(绿色),低电量(红 色)状态下,状态灯有不同显示; 4. 请勿在环境温度低于 -20℃或者高于 40℃环境中使用手表,请勿将任何液体洒 入手表内部; 5.
PUDU ROBOTICS 设备部署 硬件部署流程 1. 充电座底部有一次性黏贴片,撕下覆膜即可暴露黏贴面,充电座支持粘贴在桌面 与墙壁,当手环作为呼叫器使用时,请重点考虑充电线长度与充电座位置以部署 充电座。 2. 充电座完成部署后,只需取下手环的表带,以磁吸形式吸附在充电座即可。 3. 如果手环作为移动呼叫手表所用,则需配备呼叫卡片,呼叫卡片配附在中控中, 每一个中控默认配置 100 片呼叫卡片。 4. 手环在执行刷卡呼叫时,需先按下屏幕右侧主键,点亮屏幕,再行触碰呼叫卡片 以发起呼叫。 手环接入系统流程 手环接入系统流程 1. 好啦机器人完成环境部署,建图,添加各类元素 后,即可启动连接中控流程。 2. 请按照中控说明书,完成中控连接。 3. 完成中控连接后,需长按主键启动手环,选择当 前中控对应选择信道。(如左图) 4.
c) 按主键,进入重置数据二次确认界面 d) 按上键,选中重置按钮,在此按主键 确认重置数据 e) 设备重置完成后自动重启,即进入信 道选择界面 f)在信道选择界面可按上键或者下键选 中信道,按主键选择信道 g)完成信道选择后,设备进入等待中控 广播界面 5.
PUDU ROBOTICS 6. 处于等待中控广播的手环界面即可接收到对 应呼叫码的接入消息,点击接入,手表即弹 出接受结果。 ﹙如果添加失败,请检查手表的与中控的通 信距离,建议在添加期间,手表,网关与机 器人相距不要超过 10 米;另如果多次添加 失败,建议重置手表,并关闭添加广播,刷 新呼叫码,再次广播尝试添加) 7. 完成匹配后,请点击 ,关闭呼叫器添加广播【非常重要】。 8. 完成匹配后,手环即启动地图版本校验 9.
. 完成地图同步后,手环进入呼叫主界面,手环 会默认选中第一个餐桌号码 手环模式设置流程 1. 在此界面长按上键 3 秒,即可进入设置界面 2. 按下键,在设置界面中选中手表模式,点击 主键进入 3. 手环提供三种模式,分别是: a) 呼叫器模式:只可按下主键发起任务呼叫, 不可刷卡发起呼叫 b) 洗碗间模式:机器人抵达洗碗间后,此模式 下的手环可收到机器人抵达洗碗间的消息通知 c) 前厅模式:不可按下主键发起任务呼叫,可 通过接触呼叫卡,发起刷卡呼叫 请您按照需求选择手表的模式。 4.
PUDU ROBOTICS 手环呼叫点设置流程 1. 在此界面长按上键 3 秒,即可进入设置界面。 2. 选中呼叫点设置,按主键进入。 3. 呼叫点设置界面内展示地图内全部可发起呼 叫请求的餐桌号或者包厢,按上键或者下键 可选中,按主键可确认选中桌号。 4. 完成选中后设备默认返回设置界面,用户需点击上键回到设置界面的返回按钮, 再次点击上键,返回至手环主界面。 呼叫卡添加流程 1.
2. 点击 ,在弹出界面选择需要添加呼叫卡的餐桌或者包厢号码,点击确 定,即选中此桌号或者包厢 3. 点击 ,弹出如下界面 4.
PUDU ROBOTICS 5. 手环发生振动即代表呼叫发起,此时手环界 面如右图所示 6. 添加呼叫卡流程将迅速完成,所以手环会立 刻跳转至已抵达 7. 此时机器人界面添加呼叫卡弹窗也将显示此对应的呼叫卡号码 8.
9. 点击保存配置,即可将当前所添加呼叫卡配置完成保存 手环使用流程 前厅模式手环发起呼叫流程: 1. 手环数秒内无操作,将进入熄屏低功耗状态, 此时需点击主键,点亮屏幕。 2. 点亮屏幕后,用手环接触呼叫卡片,即可通 过呼叫卡片发起对机器人的呼叫(前厅模式 的手环只能通过接触呼叫卡片发起呼叫)。 3.
PUDU ROBOTICS 4. 当任务由机器人启动执行时,界面将跳转为 正在赶来。 5. 机器人抵达目的地后,界面跳转为已抵达, 展示若干秒后返回至呼叫主界面。 6. 在机器人抵达之前,用户可按下主键,尝试 取消呼叫。 7. 按上键,可选中“是”按钮,再点击主键,即 可取消呼叫。 呼叫器模式手环发起呼叫流程 1. 呼叫器模式手环任务发起呼叫流程与前厅模式一致。 2.
洗碗间模式手环工作流程 1. 洗碗间手环不能发起呼叫,只能接受机器人 抵达洗碗间的消息通知 2. 机器人抵达洗碗间后,洗碗间手环可收到机 器人抵达的消息通知 3.
PUDU ROBOTICS 售后服务 1. 免费保修服务 公司承诺符合以下情况,自产品收货之日起,在产品有效保修期内(产品的不同部 件保修期限有所不同),符合如下情况的将提供免费的产品保修服务。 自购买产品在规定的产品保修期限内正常使用,出现非人为的质量问题; 无擅自拆机、无非官方说明书指引的改装或加装、其它非人为引起的故障; 产品序列号、出厂标签及其他标示无撕毁、涂改迹象; 提供有效的购买证明、单据及单号 ; 免费保修期内更换的损坏备件属公司所有,应按公司要求寄回。 2. 保修范围外的售后服务 对于不在免费保修范围内的售后服务(超出保修期或者在保修期内不符合免费保修 条款),公司提供收费售后服务。 公司官方提供线上和远程技术支持渠道,客户需配合技术工程师进行问题诊断 和故障处理; 经技术工程师诊断必须上门解决问题的,指派专业技术人员提供上门服务; 不在免费保修范围内的售后服务,需按照要求填写《售后服务记录表》。服务 费用包含:售后维护费用以及备件费用。 3.
PUDU ROBOTICS Thi s devi ce compl i es wi t h par t 15 of t he FCC Rul es. Oper at i on i s subj ect t o t he condi t i on t hat t hi s devi ce does not cause har mf ul i nt er f er ence ( 1) t hi s devi ce may not cause har mf ul i nt er f er ence, and ( 2) t hi s devi ce must accept any i nt er f er ence r ecei ved, i ncl udi ng i nt er f er ence t hat may cause undesi r ed oper at i on. Any changes or modi f i cat i ons not expr essl y appr oved by t he par t y r esponsi bl e f or compl i ance coul d voi
Specific absorption rate (SAR): This Pudu Watch meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a margin of safety designed to ensure the safety of all people regardless of their age or health. The FCC Statement of Exposure to RF and the SAR limit for the United States (FCC) is 1.6 W/kg average for each gram of tissue.
Quick Guide Contents Product Overview 17 After-sales Services 29 Configurations 16 19
Product Overview PUDU ROBOTICS Thankyouforchoosingourproduct. This product is intended to be used with Pudu Holabot and LoRa CommunicationConsole.LoRaWristbandPager(hereinafterthe"Wristband") is the terminal that sends and receives messages between the robot and LoRaCommunicationConsole(hereinafterthe"Console").Theentirepaging communication system of Holabot is built on the LoRa communication schemethatrunsoveranadhocnetwork.
Product Features Item Qty LoRaWristbandPager(PW1) 1 ChargingDock 1 1 USB-AChargingCable 1 WarrantyCard 1 UserManual 1 1 1 QualityCertificate 1 Note:Beforeinstallingthegateway, checkalltheaccessoriesincludedin thepackage.Ifanythingisdamaged ormissing,pleasecontactyourseller immediately. Notes for Use 1. YoucaneitherweartheWristbandaroundyourwrist,orputitontothe chargingdockandaffixitanywhereyouwantthecalltobeinitiated. 2.
PUDU ROBOTICS Configurations Configuring the Hardware 1. Thereisadisposableadhesivesheetonthebottomofthechargingdock. Removethefilmtoexposetheadhesivesurface.Youcanstickthecharging dockontoatableorawall.WhentheWristbandisusedasapager,take thelengthofthechargingcableandthepositionofthechargingdockinto considerationintheconfiguration. 2.
c)Pressthehomebuttontogotothe confirmationscreenfordataresetting. d)PresstheUpbutton,select"Reset"and pressthehomebuttonagaintoconfirmthe operation. e)Afterthedataisreset,thedevicerestarts automaticallyandthechannelselection screenappears. f)UsetheUpandDownbuttonstoselect achannelandpressthehomebuttonto confirmyourselection. g)Afteryouarefinished,youwillbe directedtothe"AwaitingBroadcastfrom Console"screen. 5.
PUDU ROBOTICS 6. The"AwaitingBroadcastfromConsole" screenoftheWristbandchangesto displayamessagepromptingyouto acceptthecallingnumber.Tap"Accept" andyouwillseeamessageshowingthe resultoftheoperation. 7. Afteryouarefinished,taptodisablethebroadcastfor addingpagers(VERYIMPORTANT). 8. Oncethepairingissuccessful,theWristbandwillstartthemapversion checkingprocess. 9.
Setting the Wristband Modes 1. Onthisscreen,pressandholdtheUp buttonfor3secondstogoto"Settings". 2. PresstheDownbuttontoselect "WristbandModes"andpressthehome button. 3. Threemodesareavailable: a)PagerMode:Acallcanbeinitiatedby pressingthehomebutton,butnotby swipingthecallingcard. b)Dish-washingRoomMode:Oncethe robotarrivesatthedish-washingroom, theWristbandreceivesamessage notifyingthattherobothasarrived.
PUDU ROBOTICS 2. Select"CallingPointSettings"andpress thehomebutton. 3. The"CallingPointSettings"screenshows allthetablesorprivatediningroomsthat caninitiatecallrequestswithinthemap. PresstheUporDownbuttontoselect atablenumberorprivateroom,and pressthehomebuttontoconfirmyour selection. 4. Aftertheselection,youwillbedirectedbacktothe"Settings"screenby default.
2. Tapandselectthenumberofthetableorprivateroomfor whichyouwanttoaddacallingcardonthescreenthatappears.TapOKto confirmyourselection. 3. Tapandtheabovescreenappears. 4. Now,usetheWristbandforwhichyouhavefinishedthemapupdateand otherconfigurations,takeoutthecallingcardincludedwiththeConsole, lightupyourWristband,andtouchthefrontofthescreen.
PUDU ROBOTICS 5. Whenacallisinitiated,theWristband vibratesandtheabovescreenappears. 6. Asthecardaddingprocessgetsdone quickly,youwillsoonbedirectedtothe "Arrived"screen. 7. Thenumberofthecallingcardtoaddwillappearontherobotscreen. 8. TapConfirmtocompletetheprocess.(Note:Ifthecardtoaddhasbeenadded foranothertableorprivateroom,youwillbepromptedthatthecardhas beenadded,andtheoperationwillfail.
9. Tap"SaveConfigurations"tosavethecardyouhaveadded. Using the Wristband Initiating a Call in Lobby Mode 1. Thescreenwillautomaticallyturnoff whentheWristbandisleftidleforseveral seconds.Pressthehomebuttontolight upthescreen. 2. Oncethescreenlightsup,touchthe callingcardwiththeWristbandtoinitiate acalltotherobot.(AWristbandinLobby Modecaninitiateacallonlybytouching thecallingcard.) 3.
PUDU ROBOTICS 4. Whentherobotstartstoexecutethetask, the"Coming"screenappears. 5. Oncetherobotarrivesatthedestination, thescreenchangesto"Arrived",which staysputforseveralsecondsbefore returningbacktothehomescreen. 6. Youcanpressthehomebuttontotryto cancelthecallbeforetherobotarrives. 7. PresstheUpbuttontoselect"Yes",and pressthehomebuttonagaintocancelthe call. Initiating a Call in Pager Mode 1.
Working in Dish-washing Room Mode 1. InDish-washingRoomMode,the Wristbandcannotinitiatecalls;itcanonly receivemessagesaboutthearrivalofthe robot. 2. Oncetherobotarrivesatthedish-washing room,theWristbandreceivesamessage notifyingthattherobothasarrived. 3. Pressthehomebuttontoviewthestatusof alltasks.
After-sales Service PUDU ROBOTICS 1.Free Warranty Whentherobotsareunderwarranty(differentwarrantyperiodsfordifferent components,calculatedfromthereceiptoftherobot),Puduoffersafree warrantyif. Defectsarecausedbynon-humanfactors. There are no unauthorized disassembly, modification or addition not includedintheusermanual,orotherfaultscausedbynon-humanfactors. TherobotS/Nstickerandotherlabelsarenotremovedoraltered.