User manual V1.0 PT1 PuduTech Copyright © 2020 Pudu Technology Inc. All Rights Reserved.
Legal information User manual Copyright © 2020 Pudu Technology Inc. ALL RIGHTS RESERVED. CATALOG Safety Instructions Instructions for use Without the express written permission of Pudu Technology Inc., no unit or individual may Environmental notes dissemination by any means (electronic, photocopying, recording, etc.) shall not be carried Power and power requirements this manual are for reference only and are subject to change without notice.
Service functions Map settings 21 Voice settings 21 Speed settings 22 Version upgrade 22 Advanced settings 22 Parking instructions 23 Safety Instruction Instructions for use 1. DO NOT block the port of disinfectant spray, and DO NOT put anything into the port. 2. DO NOT drag the robot during the disinfection task, if necessary, tap the screen, and then push it after the pause, the disinfection mode pauses for 20s, and the robot will automatically resume moving after the pause. 3.
User manual User manual Environmental notes 1. The robot is suitable for use in flat environments such as floors, tiles, and thin carpets, it is not suitable for use in environments where there are steps, the slope is too large, or the environment is too tight. 2. It is not recommended to use the robot on wet or obviously watery ground. 3. Any kind of debris such as the power cord that has been scattered on the ground may catch or wrap the robot, be sure to remove it before use. 4.
User manual User manual 9. There is a 35cm space between the two robots placed side by side at the standby point, and a clearance of 15cm from the rear wall and 35cm from the side wall. Power and power requirements 1. When the remaining power of the robot is less than 10%, please charge it in time, as low battery operation for a long time may shorten battery life. 2. After charging, please disconnect the power supply in time, be sure not to charge for a long time when the robot is fully charged. 3.
User manual Safety instructions 1. DO NOT place any open flame on the robot, and DO NOT place any flammable solids, User manual 13. The blind-spot recognition area of the robot is shown below. gases or liquids. 2. It is forbidden to do cleaning and maintenance work when the machine is powered on. 3. To ensure safety, it is recommended to adjust the robot speed to medium or below, and it is forbidden to play in front of the robot to avoid unnecessary injury. 4.
Product Composition User manual Performance parameters Component description [1] Vision positioning sensor [5] [2] Screen [3] Depth vision sensor [4] Lidar [5] Power Switch [6] Disinfection component [7] Drive Wheel [6] [3] [4] Front Side [7] [8] PT1 Power input AC 100-240V, 50/60Hz Operating voltage [1] [2] Model Back [9] [10] [11] [8] Auxiliary Wheel [9] Key Switch [10] E-stop Switch [11] Charging Jack Power output Charging time Battery lifetime Cruise speed Applicable disinfec
User manual User manual Introduction to disinfection component Disinfectant spray nozzle Top disinfectant refilling port Disinfectio indicators green indicates the disinfection module starts running, red indicates the disinfectant is insufficient. 13 Disinfection module startup knob it is the disinfection module power-on the startup module. If the robot starts normally, you can see the green indicator of the startup knob is on.
Product Use User manual Power ON, Power OFF, Pause, Start Charging instructions Charging mode: Connect the charging interface of the robot to the charging cable to ensure that the charging port of the robot is connected to the charging cable, if the connection is successful, the robot will prompt it is charging. Before each power-on Move the robot directly below the visual mark before each power-on. Power-on Press and hold the power button for 3 seconds, and the bottom light strip will display blue.
User manual User manual Pause While the robot is running, touch the screen to make the robot pause. Disinfection mode Disinfection mode: In the disinfection mode, the robot performs intelligent circular motion according to the route selected by the user, after entering the route, the robot starts the disinfection component and starts atomizing the disinfectant to disinfect the environment; during operation, the robot does not play voice. Pauseing The screen enters the pause interface.
User manual User manual Disinfection mode 91 % Route 5.Please make sure that the disinfection Disinfection area（m²） 100 200 300 Other area Disinfection duration 100 min 4. Select or enter the indoor space area of the disinfection task. Settings Modify Start off mode knob is turned on before the disinfection task，otherwise the robot cannot start working.
Service functions User manual Speed settings Map settings With the“Speed settings”function, you can set the disinfection speed, supporting In the“Map settings”function, you can select from multiple maps. In the robot one-to-one parking mode, select the current map to configure the parking position for the robot. Basic setup 91 % Settings Basic setup WLAN 91 % Settings the speed settings of 0.5m/s, 0.6m/s, 0.7m/s, 0.8m/s and 0.9m/s. Speed（m/s） 0.5 0.6 0.7 0.8 0.
User manual Parking instructions According to the size of the use scene location, there are three robot parking options available. 1. One-to-one parking: fixed parking locations can be set for each robot. 2. Free mode: multiple parking locations can be set the robots, and the robots can be parked according to priority. 3.
User manual Sign maintenance No other objects (such as balloons, barbed wire, slogans, etc.) can be hung directly under the sign, and no billboards or safety exit signs can be hung near the sign; pay attention not to damage the sign during routine ceiling cleaning and maintenance, and the sign cannot be moved or rotated.
After Sales Free Warranty Services Shenzhen Pudu Technology Co., Ltd undertakes that, under the following circumstances, from the date of product sale, a free product warranty service will be provided during the warranty period (the warranty period for different parts of the product may vary, see the [Main Parts Warranty] for details), and the customer does not need to pay for the inspection, labor, replacement parts, test fees and courier charges for the repairs.
User manual Under the following circumstances, we have the right to reject the customer's request for replacement 1. When making the request for replacement, the customer fails to provide legal proof of purchase or documents, or the customer forges or alters the documents. 2. The goods were damaged, but the delivery person was not required for return or replacement on the spot upon customer's receipt of the goods. 3.
User manual After-sales Service Contact If you have any question, please call our service hotline: 400-0826-660 PuduTech’s after-sales service hours are: Monday to Saturday, 9:00 am to 12:00 am, 14:00 to 18:00 pm.
