型号:FBBDR1 用户手册 闪电匣机器人· V1.
用户手册 V1.
CN PUDU ROBOTICS 声明 Copyright © 2021 深圳普渡科技有限公司版权所有,保留所有权利。 未经深圳普渡科技有限公司明确书面许可,任何单位或者个人不得擅自仿制、复制、誊抄或转译本说明书部分 或者全部内容,且不得以营利为目的进行任何方式(电子、影印、录制等)的传播。本说明书所提到的产品规 格和资讯仅供参考,如果内容更新,恕不另行通知。除非有特殊规定,本说明书仅作为使用指导,所作陈述均 不构成任何形式的担保。 01
PUDU ROBOTICS 安全须知 1.1 统一说明 本产品为轮式机器人,仅限于室内平坦环境使用,如地板 , 瓷砖 , 薄地毯等,请勿用于户外(如开放式阳台)、 崎岖地面(如阶梯)等环境,请勿在环境高于 40℃或低于 0℃或地面有任何液体及粘稠物的环境下使用 运行过程中请勿拉拽或推动机器人,如需推动或者搬运机器人请先按下急停开关让其暂停。 禁止遮挡机器人元器件或放置超过装载空间的物品,否则可能导致机器人行走不正常或定位丢失。 禁止拍打设备或用力按压敲击屏幕,否则易造成设备损坏 禁止机器人超载运行,禁止承放任何可燃固、气、液体等违禁物品;不允许配送高温和汤水类物品,以免对 机器和行人造成损伤。 禁止在机器开机运行状态下做维护工作。 使用前请先将环境中地面各种线材收起,避免主机运行时拖拽。请将地面尖锐物体(如装修废料、玻璃、铁 钉等)清除,以免对机器底盘造成伤害。 为保证安全建议将机器人速度调整至 0.
PUDU ROBOTICS 需要在阶梯边沿,下坡的入口等有机器人跌落风险的地方增加栅栏或者其他阻挡防护 地面高度 20~26cm 之间有纯黑色(如踢脚线)、镜面(如墙面)、全透明(如落地玻璃窗)的物件,可能 干扰机器人雷达反射,造成机器人行走异常,可能需要对场地进行一定的改造(如粘贴贴纸)。 20~26cm 1.3 电源与用电须知 机器人剩余电量小于 20%,请及时充电,长时间低电量运行可能会缩短电池使用寿命 ; 若长时间不使用机器人,请及时将产品断电以保护机器电池 ; 务必使用原厂专配的可充电电池与充电设备 , 严禁使用非原厂充电器对机器人充电 ; 按照充电器铭牌标识的电源电压为机器人充电 ; 机器人电池故障,需联系厂家更换电池,严禁非专业人士操作 ; 请勿将机器放置于易燃易爆物体附近充电 ; 机器人存放及充电位置请保持干燥、常温,严禁将机器以及充电器放置于高温区域(> 40℃),严禁机器 以及充电器进水; 严禁充电器与外物碰撞,造成充电器损坏 ; 收到机器人报警,请立即断开充电设备 2.
PUDU ROBOTICS 2.
PUDU ROBOTICS 装载高度: 286mm 装载盘大小: 220mm*410mm 装载盘大小: 440mm*410mm 注意: 舱体中间竖向隔板可拆除。 挡板拆除方式: 05
PUDU ROBOTICS 2.3 技术规格 产品特性 描述 整机材质 高品质工程塑料 + 航空铝合金 定位方式 整机尺寸(长 * 宽 * 高) 装载区尺寸 PUDU SLAM 定位方案 539mm*515mm*1050mm 单仓(宽 * 深 * 高):219mm*410mm*286mm 双仓(宽 * 深 * 高):438mm*410mm*286mm 自重 55kg 电池容量 15.6Ah 396.396Wh 负载能力 运行速度 充电时长 续航时长 充电器输出 充电器输入 工作电压 电池容量 最小通过宽度 最大越障高度 最大爬坡角度 最大过缝宽度 最大避障距离 刹车距离 最小越障速度 紫外波长 音响功率 屏幕大小 工作温度 存储温度 ESP32 WIFI 4G 30kg(每层 15kg) 0.5~1.5m/s 可调节 4.5H 12H 29.4V 3.5A 100-240V 25.41V 15.6Ah 700mm 20mm 8° 35mm 3m 0.6m 零速越障 260-280nm 4Ω 10W 10.1 寸 0℃ - 40℃ 0℃ - 60℃ 2.
PUDU ROBOTICS 3.1 开关机说明 功能说明 开机: 将机器人推到开机定位点→打开钥匙开关→长按开关键 0.5 秒,底部灯带显示蓝色。 0.
PUDU ROBOTICS 强制关机: 长按开关机键 10 秒关机。 10s 3.
PUDU ROBOTICS 3.
PUDU ROBOTICS 3.
PUDU ROBOTICS 一键回充: 点击“一键回充”按键,机器人自动前往充电桩充电。 舱体自消毒: 设置界面中开启消毒,机器人在送物过程和待机状态下对舱体进行紫外消毒。 * 功能不定期更新,以机器实际功能为准。 11
PUDU ROBOTICS 4.1 维护与保养 售后服务 公司承诺符合以下情况,自产品收货之日起,在产品有效保修期内(产品的不同部件保修期限有所不同), 符合如下情况的将提供免费的产品保修服务。 自购买产品在规定的产品保修期限内正常使用,出现非人为的质量问题; 无擅自拆机、无非官方说明书指引的改装或加装、其它非人为引起的故障; 产品序列号、出厂标签及其他标示无撕毁、涂改迹象; 提供有效的购买证明、单据及单号 ; 免费保修期内更换的损坏备件属公司所有,应按公司要求寄回。 4.2 保修范围外的售后服务 对于不在免费保修范围内的售后服务(超出保修期或者在保修期内不符合免费保修条款),公司提供收费 售后服务; 公司官方提供线上和远程技术支持渠道,客户需配合技术工程师进行问题诊断和故障处理; 经技术工程师诊断必须上门解决问题的,指派专业技术人员提供上门服务; 不在免费保修范围内的售后服务,需按照要求填写《售后服务记录表》; 服务费用包含:售后维护费用以及备件费用。 4.
EN PUDU ROBOTICS Statement Copyright © 2021 Shenzhen PuduRobotics Co., Ltd. All rights reserved. No part of this document may be reproduced, copied, transcribed, translated, or transmitted by any means (electronic, photocopying, recording) for any profitable purpose, without prior written consent of Shenzhen PuduRobotics Co., Ltd. The product specifications and information mentioned herein are for reference only and are subject to change without prior notice.
PUDU ROBOTICS Safety Instructions 1.1 Unified Instructions This wheeled robot can only be used indoors on flat surfaces such as wood floors, ceramic tiles, and thin carpets. Using in outdoor space (for example, open balcony), on the rugged ground (for example, stairs), in a temperature above 40° C or below 0° C, or on surfaces covered with fluid or gooey stuff is not allowed. Do not pull or push the robot while it is working.
PUDU ROBOTICS The maximum possible slope is 8° for the robot. To prevent spilling, the suggested slope should be less than 5º, and the limit of 7.5° should not be exceeded. To prevent sliding, the robot should not be paused when moving uphill. To prevent falling, the slope should be at least 80cm wide, and the roll angle should not exceed 8° . 8° 8° It is necessary to add fences or other barriers at the edge of a staircase, entrance to a downslope, or other places where the robot is at risk of falling.
PUDU ROBOTICS Store and charge the robot in a dry area at room temperatures. Never place the robot and charger in an area of elevated temperatures (>40° C). Never let water get into the robot and charger. Protect the charger from collision damage. When the robot sends an alarm, disconnect the charger immediately. 2.
PUDU ROBOTICS 2.
PUDU ROBOTICS Loading height: 286mm Loading plate: 220mm*410mm Loading plate: 440mm*410mm Note: The vertical partition plate can be removed (the design needs to clearly indicate whether the robot features single or double compartment) Removal of partition plate: 18
PUDU ROBOTICS 2.
PUDU ROBOTICS ESP32 WIFI 4G 2.4GHz-2.5GHz;BT:2402-2480MHz 2.4G, 2.400GHz-2.497GHz(2.4 GHz ISM Band);5G, 4.900GHz5.845GHz(5.0 GHz ISM Band); BT: 2402-2480MHz B1/B2/B4/B5/B6/B7/B8/B12/B13/B18/B19/B20/B25/B26/B28/ B66/B34/B38/B39/B40/B41 3.1 Powering on and off Functions Power-on: Push the robot to the positioning location → Turn on the key switch → Press and hold the on/off switch for 0.5 seconds, and wait until the bottom appears in blue. 0.
PUDU ROBOTICS Forced power-off: Press and hold the power switch for 10 seconds. 10s 3.2 Charging The robot can be charged by charger and charging pile. Charge by charger: Plug the charging cable into the charging port of the robot and secure the connection. During charging, if the robot is powered on, the screen displays Charging; if it is powered off, the light strip illuminates.
PUDU ROBOTICS Light display and battery indication: Battery indication Light Display 0-30% 0-30% 30-60% 30-60% 60-90% 60-90% 90-100% 90-100% 100% Fully charged 3.3 Operations Pause: When the robot is working, press the emergency stop switch to pause the robot. If no operations are performed during the pause, the robot will proceed with its previous task During the pause, an administrator authentication is required to modify tasks.
PUDU ROBOTICS 3.4 Functions Room delivery: Enters the room delivery interface; the initial password is 0000. Place the objects and enter the destination for the compartment. Tap "Start" and the robot heads towards the destination automatically. Note: After arriving at the destination, the robot will only open the corresponding compartment to the destination.
PUDU ROBOTICS One-tap charge: Tap the "One-tap Charge" button and the robot will automatically head towards the charging pile for charging. Autonomous disinfection: After the disinfection function is enabled on the setting interface, the robot will disinfect the compartments with UV light during delivery and standby. * The function is subject to updates from time to time, and the actual function of the robot shall prevail.
After-Sales Service 4.
www.pudutech.
DECLARATION OF CONFORMITY I hereby declare that the product Description: FlashBot Type or model name: FBBDR1 Brand name: PUDU (Name of product, type or model, batch or serial number) Hardware version number: V3 Software version number: V8.1.0.12 satisfies all the technical regulations applicable to the product within the scope of Council Directives 2014/53/EU, 2014/35/EU and 2014/30/EU:and declare that the same application has not been lodged with any other notified body.
All essential radio test suites have been carried out. Feature Operation Frequency: WCDMA2100:1920-1980 MHz WCDMA900:880-915 MHz LTE Band 1: 1920-1980 MHz LTE Band 3: 1710-1785 MHz LTE Band 7: 2500-2570 MHz LTE Band 8: 880-915 MHz LTE Band 20: 832-862 MHz LTE Band 28: 703-748 MHz LTE Band 34: 2010-2025 MHz LTE Band 38: 2570-2620 MHz LTE Band 40: 2300-2400 MHz AP6353S module: BT/BLE: 2402~2480 MHz 2.4G WLAN: 802.11b/g/n(20MHz): 2412~2472MHz 802.11n(40MHz):2422~2462MHz 5G WLAN: 802.
LTE Band 1: 2.1dBi LTE Band 3: 1.4dBi LTE Band 7: 2.6dBi LTE Band 8: 2.02dBi LTE Band 20: 1.94dBi LTE Band 28: 1.94dBi LTE Band 34: 2.68dBi LTE Band 38: 1.87dBi LTE Band 40: 2.93dBi AP6353S module: BT/BLE/2.4G WLAN: 3.99dBi 5G WLAN/5.8G WLAN: ANT A: 4.01dBi, ANT B: 4.01dBi ESP32 module: BT/BLE/2.4G WLAN: 3.87dBi BL262T-H8 module: Lora: 3dBi Antenna Designation: FPC RF output Power: WCDMA2100:24.71dBm WCDMA900:24.12dBm LTE Band 1: 24.41dBm LTE Band 3: 24.88dBm LTE Band 7: 24.45dBm LTE Band 8: 24.
This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised representative. Point of contact: Le Cai/0755-26909874/Certification Director (Name, telephone and fax number) Shenzhen 2021.09.
DECLARATION OF CONFORMITY I hereby declare that the product Description: FlashBot Type or model name: FBBDR1 Brand name: PUDU (Name of product, type or model, batch or serial number) Hardware version number: V3 Software version number: V8.1.0.
NOTIFIED BODY: MiCOM Labs Inc Address: 575 Boulder Court, Pleasanton, California 94566 USA Identification Number: AB 2280 MANUFACTURER or AUTHORISED REPRESENTATIVE: Address: SHENZHEN PUDU TECHNOLOGY CO., LTD. Room 501, Building A, Block 1, Phase 1, Shenzhen International Inno Valley, Dashi 1st Road, Nanshan District, Shenzhen, China This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised representative.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Warning This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.