7535 Hand-Held Computer User Manual December 10, 2003 ISO 9001 Certified Quality Management System Part No. 8000007.
© Copyright 2003 by Psion Teklogix Inc., Mississauga, Ontario This document and the information it contains is the property of Psion Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Teklogix manufactured goods and services. Furthermore, this document is not to be used as a basis for design, manufacture, or sub-contract, or in any manner detrimental to the interests of Psion Teklogix Inc.
Return-To-Factory Warranty Psion Teklogix warrants a return-to-factory warranty for a period of one year from shipment. The warranty on Psion Teklogix manufactured equipment does not extend to any product that has been tampered with, altered, or repaired by any person other than an employee of an authorized Psion Teklogix service organization. See Psion Teklogix terms and conditions of sale for full details.
PROGRAM LICENSE AGREEMENTS Microsoft's End User License Agreement You have acquired a device (“DEVICE”) that includes software licensed by Psion Teklogix Inc. from Microsoft Licensing Inc. or its affiliates (‘MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.
License Agreement INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS. II • Note on Java Support. The SOFTWARE may contain support for programs written in Java.
License Agreement Meetinghouse Data Communications, Inc. End User License Agreement End User License Agreement: ATTENTION: PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("LICENSE") CAREFULLY BEFORE INSTALLATION. USE OF THE SOFTWARE IS SUBJECT TO THE SOFTWARE LICENSE TERMS SET FORTH BELOW. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS. IF YOU DO NOT ACCEPT THESE LICENSE TERMS, YOU MUST RETURN THE SOFTWARE FOR A FULL REFUND.
License Agreement All permanent licenses are prepaid and the Software is licensed to you by MDC. You own the media on which the Software is recorded but MDC and/or MDC’s licensor(s) retain title to the Software. The Software and any copies which this License authorizes you to make are subject to this License. Permitted Uses and Restrictions: This License allows you to install and use the Software on a single computer at a time.
License Agreement to the Software. The Software is protected by copyright and other intellectual property laws and by international treaties. MDC's third party suppliers may protect their rights in the event of any violation of these License Terms. Termination: Your rights under this License will terminate automatically without notice from MDC if you fail to comply with any term(s) of this License.
License Agreement MDC authorized representative with a copy of the receipt. THIS LIMITED WARRANTY AND ANY IMPLIED WARRANTIES ON THE MEDIA INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO NINETY (90) DAYS FROM THE DATE OF ORIGINAL RETAIL PURCHASE. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THIS LIMITATION MAY NOT APPLY TO YOU.
License Agreement RANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THE TERMS OF THIS DISCLAIMER DO NOT AFFECT OR PREJUDICE THE STATUTORY RIGHTS OF A CONSUMER ACQUIRING LICENSOR PRODUCTS OTHERWISE THAN IN THE COURSE OF A BUSINESS, NEITHER DO THEY LIMIT OR EXCLUDE ANY LIABILITY FOR DEATH OR PERSONAL INJURY CAUSED BY LICENSOR’S NEGLIGENCE.
License Agreement MDC Acknowledgments: This product includes software developed by MDC and its licensors. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)". This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).
TABLE OF CONTENTS Program License Agreements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I Approvals And Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii Chapter 1: Introduction 1.1 1.2 1.3 About This Manual . . . . . . . . . . . Text Conventions . . . . . . . . . . . . About The 7535 Hand-Held Computer . 1.3.1 Features. . . . . . . . . . . . . . 1.3.2 The 7535 Hand-Held Computer . 1.3.3 Regulatory Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 2.5 2.6 Calibrating The Touchscreen . . . . . . . . . . . . . . . . . . . . . . 28 Resetting The 7535 Hand-Held . . . . . . . . . . . . . . . . . . . . . 28 Chapter 3: Getting To Know Your 7535 3.1 3.2 3.3 3.4 3.5 3.6 3.7 ii Features Of The 7535 . . . . . . . . . . . . . . . . . . . . . . . The Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.1 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . 3.2.2 Removing And Installing The Battery Pack . . . . . . . . 3.
Contents 3.7.6 Operating Internal Two Dimensional (2D) Imager Scanners Connecting & Disconnecting Tethered Peripherals . . . . . . . . . Monitoring The Battery And Maximizing Run Time . . . . . . . . 3.9.1 Storing Batteries . . . . . . . . . . . . . . . . . . . . . . . 3.10 Monitoring The Network Connection. . . . . . . . . . . . . . . . 3.11 Uploading Data In A Docking Station . . . . . . . . . . . . . . . 3.12 General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 3.12.
Contents iv 5.3 5.4 5.5 The Control Panel . . . . . . . . . . . . . . . . Control Panel Icons . . . . . . . . . . . . . . . Basic Setup. . . . . . . . . . . . . . . . . . . . 5.5.1 Display Properties. . . . . . . . . . . . . 5.5.1.1 Display Contrast . . . . . . . . 5.5.1.2 Display Backlight . . . . . . . 5.5.1.3 Display Appearance . . . . . . 5.5.2 Keyboard Properties . . . . . . . . . . . 5.5.2.1 Key Repeat . . . . . . . . . . . 5.5.2.2 Keyboard Backlight . . . . . . 5.5.2.3 Keyboard One Shot Modes. . .
Contents 5.8 5.7.2.11 Interleaved 2 of 5 . . . . . . . . . . . 5.7.2.12 MSI Plessey . . . . . . . . . . . . . . 5.7.2.13 Discrete 2 of 5 . . . . . . . . . . . . . 5.7.2.14 IATA 2 of 5 . . . . . . . . . . . . . . 5.7.2.15 Postal: Australian . . . . . . . . . . . 5.7.2.16 Postal: Japanese . . . . . . . . . . . . 5.7.2.17 Postal: Korean . . . . . . . . . . . . . 5.7.2.18 Postal: PlaNET. . . . . . . . . . . . . 5.7.2.19 Postal: PostNET . . . . . . . . . . . . 5.7.2.20 Postal: Royal Mail . . . . . . . . . . .
Contents 6.3 6.4 6.5 6.6 6.7 6.8 6.9 vi Keyboard Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3.1 View Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3.1.1 Changing Font Sizes . . . . . . . . . . . . . . . . 6.3.1.2 Panning The Screen Contents . . . . . . . . . . . 6.3.1.3 Exiting View Mode . . . . . . . . . . . . . . . . . 6.3.2 Using The Task Manager To Switch Between Applications . The Tekterm Status Area. . . . . . . . . . . . . . . . . . . . . . . TESS Emulation . . .
Contents 6.10 6.11 6.12 6.13 6.14 6.15 6.16 6.17 6.9.1 Using The Keyboard To Navigate Through Menus . . 6.9.1.1 Sub-Menus . . . . . . . . . . . . . . . . . . 6.9.1.2 Numeric Parameters . . . . . . . . . . . . . 6.9.1.3 Y/N Parameters . . . . . . . . . . . . . . . 6.9.1.4 Alpha Parameters . . . . . . . . . . . . . . 6.9.1.5 String Entry Parameters . . . . . . . . . . . 6.9.2 Using The Touchscreen To Navigate Through Menus 6.9.2.1 Sub-Menus . . . . . . . . . . . . . . . . . . 6.9.2.2 Numeric Parameters . .
Contents 6.17.1.4 Using The Asterisk As A Wild Card . . . . . . 6.17.2 Custom Characters (Unicode™) . . . . . . . . . . . . . 6.17.2.1 Creating A Unicode™ Character. . . . . . . . 6.17.2.2 Displaying The Unicode™ Pop-up Window . . 6.18 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.18.1 ANSI Settings. . . . . . . . . . . . . . . . . . . . . . . 6.18.1.1 Host Conn . . . . . . . . . . . . . . . . . . . 6.18.1.2 Screen. . . . . . . . . . . . . . . . . . . . . . 6.18.1.3 Xmit Modes . . . .
Contents 7.2.1 Lithium-Ion Battery Safety Precautions . . . . . . . . . . . Important Charger Safety Instructions . . . . . . . . . . . . . . . Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gang Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5.2 Operator Controls . . . . . . . . . . . . . . . . . . . . . . 7.5.3 Charge Indicators. . . . . . . . . . . . . . . . . . . . . . . 7.5.
Contents 7.11 The 7535 Picker Cradle . . . . . . . . . . . . . . . . . . . . 7.11.1 Picker Cradle Mounting Recommendations . . . . . . 7.11.1.1 Mounting Template. . . . . . . . . . . . . . 7.11.2 Wiring Guidelines . . . . . . . . . . . . . . . . . . . 7.11.3 Using The Picker Cradle . . . . . . . . . . . . . . . . 7.11.4 Maintaining The Picker Cradle . . . . . . . . . . . . . 7.11.5 Powered Cradle Installation In High Voltage Vehicles 7.11.5.1 Extreme Wet Environments . . . . . . . . . 7.11.
Contents B.2 Docking Station Connector . . . . . . . . . . . . . . . . . . . . . . . B-1 B.3 Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 Appendix C: USB Setup Application C.1 USB Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.1.1 Launching The Application . . . . . . . . . . . . . . . . C.1.2 Pre-Installation: Updating usbstor.inf And wceusbsh.inf . C.1.3 Installation: Installing The 7535 As a Device On Your PC C.1.4 Post Installation . . . . . . . . . .
APPROVALS AND SAFETY SUMMARY Declaration Of Conformity Product: Application of Council Directive(s): Conformity Declared to Standards: Manufacturer: Year of Manufacture: Manufacturer’s Address in the European Community: Type of Equipment: Equipment Class: 7535 Hand Held Computer R&TTE Directive: 1999/5/EEC EMC Directive: 89/336/EEC Low Voltage Directive: 73/23/EEC Article 3.1a (Health): EN 60950: 2000 Article 3.1b (EMC): EN 301 489-17: v1.1.1; 09-2000 Article 3.2 (RF Spectrum): EN 300 328-2: v 1.1.
Approvals And Safety Summary FCC DECLARATION OF CONFORMITY (DoC) Applicant’s Name & Address: PSION TEKLOGIX 2100 Meadowvale Blvd. Mississauga, Ontario Canada L5N 7J9 Contact Person: Iain Roy Telephone No.: (905) 813-9900 US Representative’s Name & Address: 1810 Airport Exchange Blvd., Suite 500 Erlanger, KY, 41018, USA Contact Person: Joe Musgrave Telephone No.: (859) 372-4106 Equipment Type/Environment: Computing Devices Trade Name / Model No.
Approvals And Safety Summary This equipment complies with Class B Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Psion Teklogix, the party responsible for compliance, may void the user's authority to operate the equipment. 1.
Approvals And Safety Summary LASER WARNINGS For your own safety, it is critical that you comply with the following warnings: CAUTION Do not look into the laser beam or point the beam at people or animals. CAUTION Using controls or adjustments, or performing procedures other than those specified herein may result in hazardous radiation exposure. CAUTION The use of optical instruments with this product will increase eye hazard. This product contains a laser scanner that emits less than 1.
Approvals And Safety Summary CAUTION! Danger of explosion if a 7535 battery is incorrectly handled, charged, disposed of or replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions described in “Lithium-Ion Battery Safety Precautions” on page 252. Carefully review all battery safety issues.
1 INTRODUCTION 1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 About The 7535 Hand-Held Computer 1.3.1 Features . . . . . . . . . . . . . 1.3.2 The 7535 Hand-Held Computer . 1.3.3 Regulatory Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 . . . . . . . 5 . . . . . . . 7 . . .
Chapter 1: Introduction About This Manual 1.1 About This Manual This manual describes how to configure, operate and maintain the Psion Teklogix 7535 hand-held computer. Chapter 1: Introduction provides a basic overview of the 7535 hand-held. Chapter 2: Basic Checkout describes the steps required to get the 7535 ready for operation. Chapter 3: Getting To Know Your 7535 describes the 7535 features and outlines how to charge and maintain the battery.
Chapter 1: Introduction Text Conventions 1.2 Text Conventions Note: Notes highlight additional helpful information. 4 Important: These statements provide particularly important instructions or additional information that is critical to the operation of the equipment. Warning: These statements provide critical information that may prevent physical injury, equipment damage or data loss.
Chapter 1: Introduction About The 7535 Hand-Held Computer 1.3 About The 7535 Hand-Held Computer The 7535 is a ruggedized hand-held personal computer, running the Microsoft® Windows® CE.net operating system. It is intended for use in commercial and light industrial applications with a focus on real time wireless data transactions. All possible bar code input methodologies are supported by one of the variety of scanners available.
Chapter 1: Introduction Features - 6 standard antenna integrated onto radio card. optional high performance internal antenna available. Bluetooth SD I/O radio. • Expansion slot: - SD I/O slot that supports extra FLASH memory (up to 512 MB) • Programming environment: - HTML - .net Compact framework - Java, Visual C++ • Bar code applications: - internal 1D and 2D scan engines. - internal CMOS image capture scan engine. - supports decoded and undecoded tethered scanners.
Chapter 1: Introduction The 7535 Hand-Held Computer 1.3.2 The 7535 Hand-Held Computer Figure 1.
Chapter 1: Introduction The 7535 Hand-Held Computer Figure 1.2 7535 Docking Port Figure 1.3 Tether Port Figure 1.
Chapter 1: Introduction Regulatory Labels 1.3.3 Regulatory Labels Figure 1.5 Laser Warning Labels Figure 1.
Chapter 1: Introduction Regulatory Labels Figure 1.7 Manufacturer’s Label Warning: 10 Using controls or adjustments or performing procedures other than those specified herein may result in hazardous radiation exposure.
2 BASIC CHECKOUT 2.1 Preparing The 7535 For Operation . . . . . . . . . . . . . . . . 2.1.1 Equipment You Need To Get Started . . . . . . . . . . . . 2.1.2 Charging The Battery . . . . . . . . . . . . . . . . . . . . 2.1.3 Attaching Carrying Accessories . . . . . . . . . . . . . . 2.1.3.1 Attaching The Hand Strap . . . . . . . . . . . . . 2.1.3.2 Attaching The Pistol Grip . . . . . . . . . . . . . 2.2 Powering Up The 7535 And Configuring The Radio . . . . . . . 2.2.
Chapter 2: Basic Checkout Preparing The 7535 For Operation 2.1 Preparing The 7535 For Operation Typically, 7535 hand-helds are configured at the factory and arrive ready for use. Although the 7535 is equipped with an internal Compact Flash and SD I/O slot, these slots are not intended for user modification. If a device needs to be changed or added in these slots, contact qualified Psion Teklogix personnel. Refer to Appendix A: Support Services And Worldwide Offices for the service number closest to you.
Chapter 2: Basic Checkout Attaching The Hand Strap Important: 2.1.3.1 Do not use adhesives such as Loctite to secure the screws on the carrying accessories. These chemicals may damage the plastic casing. Attaching The Hand Strap Note: A Phillips head screwdriver is required. Two Phillips head screws are provided with the hand strap. • Attach the strap to the two threaded inserts located at the back of the 7535 near the top of the unit. Figure 2.
Chapter 2: Basic Checkout Attaching The Pistol Grip • Stretch the handstrap toward the base of the 7535, and hook the bottom of the handstrap into the slot near the base of the battery pack. Figure 2.2 Hooking The Hand Strap To The 7535 2.1.3.2 Attaching The Pistol Grip Note: A Phillips head screwdriver is required. The pistol grip is attached to the back of the 7535 using the four threaded inserts in the upper part of the 7535 casing.
Chapter 2: Basic Checkout Powering Up The 7535 And Configuring The Radio • Position the pistol grip so that it fits snugly over the back of the unit and the inserts on the back of the 7535 align with the holes in the pistol grip. Figure 2.3 Attaching The Pistol Grip • Using a Phillips screwdriver, securely fasten the pistol grip to the back of the 7535. 2.
Chapter 2: Basic Checkout Installing The Battery And Switching The 7535 On 2.2.1 Installing The Battery And Switching The 7535 On If you are not using a docking station or PDM: • Slide the charged battery with the contoured plastic facing you into the 7535. Click the battery into place. Figure 2.4 Installing The Battery Note: If you are using a docking station, you can insert an uncharged battery, dock the unit and switch it on.
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio Installed In The 7535 2.2.2 Configuring An IEEE 802.11 Radio Installed In The 7535 The most common 802.11b settings are configured as defaults. However, there are some fields that must be completed, including the SSID of your access point and the security methods implemented in the network (including access keys).
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio Installed In The 7535 2. Choose the radio icon to open the 802.11b Wireless LAN Settings window – in the sample screen this is labelled $NETWLAN1. Figure 2.6 802.11b Wireless LAN Settings Window 3. Wireless Statistics Tab When you choose the Wireless LAN icon, an 802.11b Wireless LAN Settings window ($NETWLAN1 in the sample below) is displayed. Figure 2.7 Wireless Statistics This tab lists your radio statistics.
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio Installed In The 7535 4. Wireless Information Tab The options under this tab display existing networks to which you can connect, and it allows you to add a new network or modify the settings for an existing network. Note: Configure button – To change the settings in an existing network, highlight the network you want to modify, and choose the Configure button to display the Wireless Properties dialogue box.
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio Installed In The 7535 5. Wireless Properties Figure 2.9 Wireless Properties Dialogue Box Network name (SSID): • Type the appropriate SSID (Service Set Identifier) in the ‘Network name (SSID):’ text entry field at the top of this dialogue box. The Network name field can contain a maximum of 32 characters. The name assigned here is listed as a preferred network.
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio Installed In The 7535 Authentication 802.11 supports two subtypes of network authentication services: Open and Shared. Under Open authentication, any wireless station can request authentication. The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the sending station.
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio Installed In The 7535 Enable 802.1x authentication “802.1X” is the IEEE standard that offers additional security for local area networks. It provides authentication for user devices attached to an Ethernet network, whether wired or wireless. A security protocol packet such as TLS or MD5 encapsulated in an “EAP” is used in conjunction with the “802.1x” standard to authenticate users at the MAC layer.
Chapter 2: Basic Checkout Assigning An IP Address 2.2.3 Assigning An IP Address If your network is not using a DHCP server, you will need to assign an IP address. • In the $NETWLAN1 Settings window, press the key followed by the arrow key to display the IP Information tab. Figure 2.11 IP Information Note: Choosing the Renew button forces the 7535 to renew or find a new IP address.
Chapter 2: Basic Checkout Name Servers Tab • • Press the arrow key to highlight Specify an IP address. Press the key to move from field to field, and type an IP, Subnet Mask and Default Gateway address. Press to save your information. 2.2.4 Name Servers Tab Note: If DHCP is enabled, name server addresses are assigned automatically. • • • In the $NETWLAN1 Settings window, press the key followed by the arrow key to display the IP Information tab.
Chapter 2: Basic Checkout Advanced Features 2.2.5 Advanced Features To display the Advanced Wireless Settings dialogue box: • Highlight the Advanced... button in the Wireless Information tab and press . This window lists the available preferred networks. Figure 2.14 Advanced Settings 2.2.5.1 Rearranging Preferred Networks The 7535 attempts to connect with the networks listed in this dialogue box in sequence, beginning at the top of the list.
Chapter 2: Basic Checkout Deleting A Preferred Network 2.2.5.2 Deleting A Preferred Network To delete a network from this list: • Press the key to highlight the networks list. • Use the or arrow keys to highlight the network that you want to remove. • Highlight the Delete button, and press . 2.2.5.3 Changing Network Properties To change the properties of an existing preferred network: • Highlight the network that you want to modify.
Chapter 2: Basic Checkout Calibrating The Touchscreen To install ActiveSync, follow the step-by-step instructions provided with the program’s setup wizard. Refer to the following website for details: http://www.microsoft.com/windowsmobile/resources/downloads/pocketpc/activesync35.mspx 2.5 Calibrating The Touchscreen If your 7535 is equipped with a touchscreen, it will need to be calibrated. Refer to “Calibrating The Touchscreen” on page 41 for details. 2.
3 GETTING TO KNOW YOUR 7535 3.1 Features Of The 7535 . . . . . . . . . . . . . . . . . . . . . . . . 3.2 The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.1 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . 3.2.2 Removing And Installing The Battery Pack . . . . . . . . . 3.2.3 Charging The Battery . . . . . . . . . . . . . . . . . . . . . 3.3 Switching The 7535 Hand-Held On And Off . . . . . . . . . . . . 3.4 The Keyboard . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3: Getting To Know Your 7535 3.8 Connecting & Disconnecting Tethered Peripherals . 3.9 Monitoring The Battery And Maximizing Run Time 3.9.1 Storing Batteries. . . . . . . . . . . . . . . . 3.10 Monitoring The Network Connection . . . . . . . 3.11 Uploading Data In A Docking Station . . . . . . . 3.12 General Maintenance. . . . . . . . . . . . . . . . 3.12.1 Caring For The Touchscreen . . . . . . . . . 3.12.2 Cleaning The 7535 . . . . . . . . . . . . . .
Chapter 3: Getting To Know Your 7535 Features Of The 7535 3.1 Features Of The 7535 7535 Screen Sound Port Ambient Light Sensor Tether Port Docking Port Figure 3.1 Front Of 7535 Stylus (Pointing Tool) Scanner Window Battery Pack Tether Port Figure 3.
Chapter 3: Getting To Know Your 7535 The Battery 3.2 The Battery The 7535 hand-held operates with a Lithium-Ion battery pack. Preparing the hand-held unit for operation requires that a battery pack be charged and installed in the unit. 3.2.1 Battery Safety Important: Before attempting to install, use or charge the battery pack, it is critical that you review and follow the important safety guidelines in the section entitled “Lithium-Ion Battery Safety Precautions” beginning on page 252. 3.2.
Chapter 3: Getting To Know Your 7535 Charging The Battery Installing The Battery Pack To install the battery pack: • Slide the battery pack with the contoured plastic facing you into the 7535. Click the battery into place. Figure 3.3 Installing The Battery Pack • If your computer is equipped with a hand strap, insert the hook at the end of the hand strap into the slot at the base of the battery. 3.2.
Chapter 3: Getting To Know Your 7535 Switching The 7535 Hand-Held On And Off • • • Combo Docking Station (Model #HU4002) – operates as both a charger and a docking station. Operating as a charger, both the battery installed in the computer and a spare battery can be charged simultaneously. Quad Docking Station (Model #HU4004) – can charge the battery of up to four 7535s inserted in the docking station while transferring data through an Ethernet connection.
Chapter 3: Getting To Know Your 7535 The Keyboard Switching Off The 7535 Important: Keep in mind that turning off the 7535 does not result in a complete reboot; rather, the unit enters a power-saving, “suspend” state. When the 7535 is turned on from suspend state, operation resumes within a few seconds. To switch off the 7535: • Press the key, and then press the key.
Chapter 3: Getting To Know Your 7535 Activating Modifier Keys The , and keys operate much like a desktop keyboard except that they are not chorded (two keys held down simultaneously). The modifier key must be pressed first followed by the key whose function you want modified. 3.4.1.1 Activating Modifier Keys When a modifier key is pressed once, it is displayed in lowercase letters in the taskbar at the bottom of the 7535 screen.
Chapter 3: Getting To Know Your 7535 The 58-Key Keyboard The Key The key (sometimes referred to as destructive backspace) moves the cursor one character to the left, erasing the incorrectly entered key stroke. The key ( ) erases the character at the cursor position. The And Key The and keys modify the function of the next key pressed and are application dependent.
Chapter 3: Getting To Know Your 7535 The 36-Key Keyboard 3.4.4 The 36-Key Keyboard On 36-key 7535s, all alpha characters are printed on the unit plastic in orange typeface above the numeric keys. To access an alpha character, you must first press the key and then press the numeric key above which the alpha character you want to type is printed.
Chapter 3: Getting To Know Your 7535 The 36-Key Keyboard Choosing More Than One Alpha Character From The Same Key If you need to choose more than one alpha character from a single key, you’ll need to press the ‘Accept’ key between alpha selections. The ‘Accept’ key is presented as an arrow ⇒ symbol above the ‘0’ (zero) key. Pressing this key signals the 7535 to display the alpha character you’ve chosen and await the next selection from the same key.
Chapter 3: Getting To Know Your 7535 The Keypad Backlight Suppose you want to type the letters ‘a’, ‘d’ and ‘g’. These alpha characters are accessed from the numeric keys <2>, <3> and <4>. • • • With the key locked ‘on’ (press twice), press <2> to type the letter ‘a’. Press <3> to type ‘d’, and press <4> to type the letter ‘g’. To end alpha selection, press the key a third time to unlock it. 3.4.
Chapter 3: Getting To Know Your 7535 Adjusting The Contrast 3.5.2 Adjusting The Contrast Note: In addition to the manual adjustments described in this section, the display contrast can also be adjusted using the Windows CE Control Panel. Refer to “Display Contrast” on page 88 for details about this dialogue box. The display contrast can be adjusted from the unit keyboard using the key and function keys and . Pressing darkens the display, and pressing lightens the display.
Chapter 3: Getting To Know Your 7535 7535 Indicators • Select the Calibration tab, and then choose the ‘Recalibrate’ button. Figure 3.5 Calibration Screen • Follow the directions on the calibration screen to calibrate the screen. 3.6 7535 Indicators 7535s use LEDs (Light Emitting Diode), onscreen messages and audio tones as indicators. 3.6.1 LEDs The 7535 is equipped with four tri-coloured LEDs. This section outlines what these LEDs indicate.
Chapter 3: Getting To Know Your 7535 Charge LED User Application LED Radio Traffic LED Scanner LED Charge LED Figure 3.6 Keyboard LEDs 3.6.1.1 Charge LED The lower-right LED is reserved for internal charger/power status. This indicator is active even when the 7535 is inserted in a docking station (and in suspend mode) so that the charge status of the battery can be detected easily. Function Charge LED Behaviour External power not available. Fully charged to within 95% of charge capacity.
Chapter 3: Getting To Know Your 7535 Radio Traffic LED 3.6.1.2 Radio Traffic LED The upper-left LED on your 7535 flashes either orange or green to indicate when the radio transmits and receives data. Note: Keep in mind that while the standard 802.11b radio supports the transmit/receive LED, not all radios support this function. Function Radio Traffic LED Behaviour Radio Transmit Radio Receive LED flashes orange. LED flashes green. Table 3.2 Transmit and Receive LEDs 3.6.1.
Chapter 3: Getting To Know Your 7535 Onscreen Indicators 3.6.2 Onscreen Indicators The taskbar at the bottom of the screen displays a variety of system status indicators. Figure 3.7 Taskbar This display changes dynamically, and only those icons that are applicable are displayed. For example, if a radio is not installed in your 7535, the radio signal icon is not displayed in the taskbar.
Chapter 3: Getting To Know Your 7535 Onscreen Indicators Modifier Key Indicators , , , and are modifier keys that have onscreen indicators to show when a key is active or locked. If a modifier key is pressed once to activate it, the key is displayed in the taskbar in lowercase characters – for example, pressing the key once displays blue key in the taskbar.
Chapter 3: Getting To Know Your 7535 Audio Indicators Tethered Devices When a peripheral is attached to the tether port and activated, an associated icon appears in the taskbar. The sample to the left indicates that a USB device is connected to the tether port. Scanner USB Device RFID Serial Device Scan-See Docking Device When a 7535 is inserted in a docking station, charger or cradle, an associated icon appears in the taskbar.
Chapter 3: Getting To Know Your 7535 Adjusting The Beeper Volume 3.6.3.1 Adjusting The Beeper Volume On 58-key keyboards, the volume function keys are accessed by pressing and . On 36-key keyboards, the volume function keys are accessed by pressing < F3> and . To adjust the beeper volume: • • Press the key twice to lock the key ‘on’ and then, press the increase volume function key or the decrease volume function key until the volume is meets your requirements.
Chapter 3: Getting To Know Your 7535 Scanning Techniques 3.7.1 Scanning Techniques Note: The scanning techniques described here apply to internal and external scanners. • • • • • • Hold the scanner at an angle. Do not hold it perpendicular to the bar code. Do not hold the scanner directly over the bar code. In this position, light can reflect back into the scanner’s exit window and prevent a successful decode. Scan the entire bar code.
Chapter 3: Getting To Know Your 7535 Troubleshooting 3.7.3 Troubleshooting If the scanner is not working, investigate the following: • Is the 7535 on? • Check that the bar code symbology being scanned is enabled for the 7535 you are using. Check any other parameters that affect the scanning procedure or the bar code. • Check the bar code to make sure it is not damaged. Try scanning a different bar code to verify that the problem is not with the bar code.
Chapter 3: Getting To Know Your 7535 Operating Internal PDF Laser Scanners 3.7.5 Operating Internal PDF Laser Scanners This scanner decodes PDF417 two-dimensional bar codes. • • Turn the 7535 on. Wait until the unit has booted up completely. Aim at the bar code and press the scan key or the trigger. The beam expands into a rectangle covering the bar code to properly scan it. The scan beam and a warning indicator are visible until a successful decode is achieved or three seconds have elapsed. 3.7.
Chapter 3: Getting To Know Your 7535 Connecting & Disconnecting Tethered Peripherals • When the scan button or trigger is pressed, a red, oval shaped light (the framing marker) is displayed. Centre the framing marker in the field – either in the centre of the bar code you want to scan or in the centre of the area in which multiple bar codes are to be scanned. Illumination LEDs will flash and a picture of the bar code(s) is taken. 3.
Chapter 3: Getting To Know Your 7535 Monitoring The Battery And Maximizing Run Time To remove the peripheral: • Grasp the shell of the plug, and pull it back gently to unlock and release the connector. Figure 3.9 Disconnecting The Tether Cable Important: Never attempt to disconnect a peripheral by pulling the connector by the wire. The connector is locked into place and can only be unlocked and removed by pulling back the plug shell. 3.
Chapter 3: Getting To Know Your 7535 Monitoring The Battery And Maximizing Run Time To maximize the run time of your batteries, consider the following: • • • The display backlight is the largest drain on the battery. Try to keep its brightness as low as possible. The hand-held is ‘event’ driven – that is, when the unit is not in use, it reverts to sleep mode (even when it appears to be running), saving battery power. Events include a key press, touchscreen taps and scan triggers.
Chapter 3: Getting To Know Your 7535 Storing Batteries 3.9.1 Storing Batteries Long term battery storage is not recommended. If storage is necessary: • • • • • Always try to use a ‘first-in first-out’ approach to minimize storage time. Lithium-Ion batteries age much faster at elevated temperatures. Store batteries at temperatures between 0˚ C and 20˚C. Always charge batteries to 40 to 60% before storing them.
Chapter 3: Getting To Know Your 7535 Uploading Data In A Docking Station 3.11 Uploading Data In A Docking Station The Combo Docking and Quad Docking peripherals allow the 7535 to link to an Ethernet network. They are typically used to upload transaction data to a server computer when a radio link in not available. When a 7535 is properly inserted in a docking station, a dock icon is displayed in the taskbar at the bottom of the 7535 screen. The 7535 also detects the presence of the Ethernet network.
Chapter 3: Getting To Know Your 7535 Cleaning The 7535 3.12.2 Cleaning The 7535 Important: • • • Do not immerse the unit in water. Dampen a soft cloth with mild detergent to wipe the unit clean. Use only mild detergent or soapy water to clean the hand-held unit. Avoid abrasive cleaners, solvents or strong chemicals for cleaning. The 7535 has a plastic case that is susceptible to harsh chemicals. The plastic is partially soluble in oils, mineral spirits and gasoline.
4 WORKING WITH WINDOWS CE 4.1 Navigating In Windows CE And Applications . . . 4.1.1 Navigating Using A Touchscreen And Stylus 4.1.2 Navigating Using The Keyboard . . . . . . . 4.2 Working With Files, Folders And Programs . . . . 4.3 The Startup Desktop . . . . . . . . . . . . . . . . 4.3.1 The Desktop Icons . . . . . . . . . . . . . . 4.3.2 The Taskbar . . . . . . . . . . . . . . . . . . 4.3.2.1 Using The Taskbar . . . . . . . . . . 4.3.2.2 Customizing The Taskbar . . . . . . 4.4 The Start Menu . . . . . .
Chapter 4: Working With Windows CE Navigating In Windows CE And Applications 4.1 Navigating In Windows CE And Applications Graphic user interfaces like Windows CE for portable devices and desktop Windows (2000, XP, etc.) utilize ‘point and click’ navigation. An equivalent keyboard shortcut is also available for every ‘point and click’ action.
Chapter 4: Working With Windows CE Navigating Using The Keyboard 4.1.2 Navigating Using The Keyboard If your 7535 has a standard screen (rather than a touchscreen), choosing icons and navigating dialogue boxes, displaying the desktop, and so on requires keyboard input. If your unit has already been fully configured and your application is launched at startup, you’ll have little need for keyboard navigation.
Chapter 4: Working With Windows CE Working With Files, Folders And Programs 4.2 Working With Files, Folders And Programs Folder Program Icon File Figure 4.1 Working With Windows Icons • • Use the arrow keys to highlight the icon you want to open or launch. Press . If you have a touchscreen: • Double-tap on the appropriate icon – either a folder icon, a program icon or a file icon – to open or launch your selection.
Chapter 4: Working With Windows CE The Startup Desktop 4.3 The Startup Desktop When the 7535 boots up, the startup desktop (shell) is displayed. Any applications stored in the Startup folder start up immediately. Note: The startup folder is located in \Windows\StartUp and \Flash Disk\StartUp. Figure 4.2 The 7535 Startup Desktop To access desktop icons: • Use the arrow keys to highlight the icon, and press to launch the highlighted icon.
Chapter 4: Working With Windows CE The Desktop Icons 4.3.1 The Desktop Icons The icons displayed in the startup desktop operate in much the same way as those displayed on any standard PC desktop that is running Windows®. My Computer Choosing this icon displays the contents of your 7535 computer. If you’re not sure how to work with the files, folders and programs displayed, refer to “Working With Files, Folders And Programs” on page 63.
Chapter 4: Working With Windows CE The Taskbar 4.3.2 The Taskbar Figure 4.3 The Taskbar The 7535 is equipped with a taskbar at the bottom of the screen. It displays icons through which you can view the battery capacity and radio signal quality of your unit. If the hand-held is attached to a charger, cradle, docking station or PDM, an associated icon is displayed. In addition, the taskbar displays the application(s) currently running on your unit and the security level assigned to your 7535.
Chapter 4: Working With Windows CE Customizing The Taskbar 4.3.2.2 Customizing The Taskbar To customize the taskbar so that it displays only those icons you require: • • Press <0> (zero) to display the Start Menu. Highlight the Settings option, highlight Taskbar... in the sub-menu, and press . The Taskbar and Start Menu dialogue box is displayed. Figure 4.
Chapter 4: Working With Windows CE The Start Menu 4.4 The Start Menu Note: Some of the Start Menu items may be disabled based on the 7535’s current security settings. The Start Menu lists the operations you can access and work with. It is available from the startup desktop or from within any application. To display the menu: • Press <0> (zero). Figure 4.
Chapter 4: Working With Windows CE Security Settings 4.4.2 Security Settings Choosing the Security option from the Start Menu displays a dialogue box in which you can define the access level for the 7535 – Teklogix, Supervisor or User. Figure 4.6 Security Levels Security Level These security levels define the options accessible to the operator in the Start Menu and the taskbar. When you change security levels, you’ll need to enter the appropriate password in the Password textbox.
Chapter 4: Working With Windows CE The System Tray Configuring Security Choosing the Configure button displays the Configure Security dialogue box. Figure 4.7 Configuring Security This dialogue box allows you to determine which security levels will have an associated icon displayed in the taskbar. By default, a security icon is not displayed for user-level security. 4.4.3 The System Tray The System Tray option allows access to the icons in the taskbar at the bottom of the screen.
Chapter 4: Working With Windows CE The Task Manager 4.4.4 The Task Manager The Task Manager option allows you to switch to another task or to end an active task. To display the task manager window: • • Press <0>, or Press . Figure 4.8 Task Manager 4.4.5 Cycle Tasks When Cycle Tasks is selected (and the Task Manager is not open), you can cycle through active applications. To choose this option: • • Press <0>, and type , or Press . 4.4.
Chapter 4: Working With Windows CE Programs 4.4.7 Programs With Programs highlighted, press the arrow key to display a sub-menu of options. Figure 4.9 Program Sub-Menu This sub-menu allows you to choose ActiveSync and Command Prompt, and you can access the Internet Explorer, installed applications (e.g., Open Tekterm), Remote Desktop Connection or Windows Explorer. ActiveSync® This option allows you to connect to another device using ActiveSync.
Chapter 4: Working With Windows CE Settings Windows Explorer Windows Explorer installed on your 7535 is consistent with all Windows CE.NET 4.2 devices. You can access this option either from the Start Menu under Programs>Windows Explorer. Remote Desktop Connection Remote Desktop Connection is a 7535 application used to connect to a Windows Terminal Server so that you can run a “session” on the Server machine using the 7535 (Windows CE device).
Chapter 4: Working With Windows CE Run Network And Dial-Up Connections The Network and Dial-up Connections window allows you to configure the 7535 radio or execute an existing configuration. Refer to “Configuring An IEEE 802.11 Radio Installed In The 7535” on page 18 for radio setup details. Taskbar And Start Menu The Taskbar and Start Menu option displays a dialogue box in which you can customize the taskbar, choosing which options will be displayed.
Chapter 4: Working With Windows CE Shutdown 4.4.10 Shutdown With Shutdown highlighted, pressing the arrow key displays a sub-menu of options, including Suspend, Warm Reset and Cold Reset. Figure 4.12 Shutdown Sub-Menu Note: This menu varies slightly depending on the security level chosen. When the 7535 is set to User level, the Shutdown option is replaced by Suspend. A sub-menu is not available. At Teklogix security level, an additional option is available in the sub-menu – Bootloader.
Chapter 4: Working With Windows CE Using A Dialogue Box 4.5 Using A Dialogue Box A dialogue box (like the samples in Figure 4.13) appears when you need to make selections and enter further information. You can move between dialogue items by tapping on them, or by pressing the arrow keys and the key. ( moves the cursor backwards.) Tabs Radio Button Textbox Dropdown Menu Checkbox Button Figure 4.
Chapter 4: Working With Windows CE Using A Dialogue Box Checkbox: This box allows you to select or deselect an option. To select or deselect a checkbox, press the key to highlight the checkbox, and press the key to select (√) or deselect it. Radio buttons: These buttons allow you to choose from a number of options. For example, in the sample screen in Figure 4.13 on page 76 you can choose to ‘Obtain an IP address via DHCP’ or ‘Specify an IP address’.
5 CONFIGURATION 5.1 5.2 5.3 5.4 5.5 Remote Desktop Connection . . . . . . . . . Pocket PC Compatibility . . . . . . . . . . . The Control Panel . . . . . . . . . . . . . . . Control Panel Icons . . . . . . . . . . . . . . Basic Setup . . . . . . . . . . . . . . . . . . 5.5.1 Display Properties . . . . . . . . . . . 5.5.1.1 Display Contrast . . . . . . . . 5.5.1.2 Display Backlight . . . . . . . 5.5.1.3 Display Appearance . . . . . . 5.5.2 Keyboard Properties . . . . . . . . . . 5.5.2.1 Key Repeat. . . . .
Chapter 5: Configuration 5.7.2.3 EAN 13 Settings . . . . . . . . . . . . . 5.7.2.4 EAN 8 . . . . . . . . . . . . . . . . . . 5.7.2.5 UPC And EAN Settings . . . . . . . . . 5.7.2.6 UPC A Settings. . . . . . . . . . . . . . 5.7.2.7 UPC E Settings . . . . . . . . . . . . . . 5.7.2.8 Codabar. . . . . . . . . . . . . . . . . . 5.7.2.9 Code 93. . . . . . . . . . . . . . . . . . 5.7.2.10 Code 11 . . . . . . . . . . . . . . . . . 5.7.2.11 Interleaved 2 of 5 . . . . . . . . . . . . 5.7.2.12 MSI Plessey . . . . . . .
Chapter 5: Configuration 5.8.4 Permitted Hosts Tab . . . . . . . . . . . . . . . . . . . . . . . . 141 5.8.4.1 Adding A Host . . . . . . . . . . . . . . . . . . . . . . . 141 5.8.4.2 Changing A Host. . . . . . . . . . . . . . . . . . . . . .
Chapter 5: Configuration Remote Desktop Connection 5.1 Remote Desktop Connection Remote Desktop Connection is a 7535 application used to connect to a Windows Terminal Server so that you can run a “session” on the Server machine, using the 7535 (Windows CE device). Refer to the following website for step-by-step information about setting up this connection: http://www.microsoft.com/WindowsXP/pro/using/howto/gomobile/remotedesktop/default.asp 5.
Chapter 5: Configuration Control Panel Icons If you have a touchscreen: • Use the stylus to tap on the Windows Start button in the taskbar to display the Start Menu. Tap on Settings>Control Panel. The Control Panel folder contains icons used in the setup of your 7535. Figure 5.1 Control Panel 5.4 Control Panel Icons The Windows CE Control Panel provides a group of icons that allow you to customize and adjust settings on your 7535.
Chapter 5: Configuration Control Panel Icons Volume & Sound Allows you to adjust the volume of the beep that is emitted to indicate events like warnings, key clicks and, if your unit is equipped with a touchscreen, screen taps. Sounds (wave files) cannot be reproduced on 7535 units. The beeper volume and the conditions under which it sounds are tailored from within the application installed on your unit.
Chapter 5: Configuration Control Panel Icons Regional Settings Allows you to specify the local language the display text will use along with the format of numbers, currency, time and date for your region. Remove Programs Lists the programs that can be removed from your unit. To remove a program, select it and then click on the Remove button. Stylus Adjusts how Windows CE recognizes your double-tap (as slow or rapid successive taps).
Chapter 5: Configuration Control Panel Icons PC Connection Enables direct connections to a desktop computer. Selecting the ‘Change Connection’ button allows you to change the type of direct connect to your PC. Teklogix Scanners Used to set up scanner parameters and choose the bar code symbologies that the 7535 scanner will successfully read. Network And Dial-up Connections Displays a network window from which the 7535 radio can be configured and an existing configuration can be executed.
Chapter 5: Configuration Basic Setup 5.5 Basic Setup 5.5.1 Display Properties • In the Control Panel, choose the Display icon. Figure 5.2 Choosing The Display Icon 5.5.1.1 Display Contrast The Contrast tab allows you to adjust the 7535 display contrast to suit the environment in which you are using the hand-held.
Chapter 5: Configuration Display Backlight • In the Display Properties dialogue box, open the Contrast tab. Figure 5.3 Display Contrast Properties Sliding bar in the Contrast tab to the left decreases or darkens the display contrast. Sliding the bar to the right to increases or lightens the display contrast. 5.5.1.
Chapter 5: Configuration Display Backlight • In the Display Properties dialogue box, open the Backlight tab. Figure 5.4 Display Backlight Properties Note: Backlight changes take affect immediately. You do not need to reset the 7535. ON Threshold The 7535 is equipped with an ambient light sensor. This sliding bar allows you to determine how dark the ambient light needs to be before the backlight turns on. Intensity This parameter is used to adjust the light intensity of the 7535 backlight.
Chapter 5: Configuration Display Appearance External Power Checkbox When you select (√) the checkbox next to ‘When using external power keep the backlight always ON.’, the backlight remains ON at the configured intensity when the 7535 is operating with external power (not battery power). If the 7535 is drawing power from its battery, this option is ignored and the other parameters defined in Display Properties dialogue box take affect. 5.5.1.
Chapter 5: Configuration Keyboard Properties 5.5.2 Keyboard Properties This icon displays the Keyboard Properties dialogue box in which you can adjust the repeat rate of the keys, the intensity of the keyboard backlight and the behaviour of the and modifier keys. This dialogue box also allows you to define macro keys and Unicode characters. • In the Control Panel, choose the Keyboard icon. Figure 5.6 Choosing The Keyboard Icon 5.5.2.
Chapter 5: Configuration Keyboard Backlight Repeat Delay The value assigned for this parameter determines the delay in milliseconds between repeat characters. Sliding the Repeat Delay bar to the left increases the delay between key repeats while sliding the bar to the right shortens the repeat delay time. Repeat Rate The value assigned for the Repeat Rate parameter determines how quickly the key you press repeats and is measured in characters per second (cps).
Chapter 5: Configuration Keyboard One Shot Modes ON Time The value chosen from this dropdown menu determines the duration of time that the keyboard backlight stays on when a unit is not in use. 5.5.2.3 • Keyboard One Shot Modes In the Keyboard Properties dialogue box, open the One Shots tab. Figure 5.9 Keyboard One Shot Properties When these options are enabled (√), the and keys only remain active until the next key is pressed.
Chapter 5: Configuration Keyboard Macro Keys 5.5.2.4 • Keyboard Macro Keys In the Keyboard Properties dialogue box, open the Macros tab. Figure 5.10 Macro Dialogue Box A macro has 20 programmable characters (or “positions”). The macro keys can be programmed to replace frequently used keystrokes, along with the function of executable keys including , and (-), function keys and arrow keys.
Chapter 5: Configuration Keyboard Macro Keys A message screen is displayed instructing you to ‘Please Enter Key Strokes’. Figure 5.11 Recording A Macro • • Type the macro sequence you want to assign to the Macro key. You can type text and numbers, and you can program the function of special keys into a macro. When you’ve finished recording your macro sequence, press the key sequence – . A new screen displays the macro sequence you created. The Save Macro button is highlighted.
Chapter 5: Configuration Unicode Mapping Deleting A Macro To delete a macro: • • 5.5.2.5 • In the Macros tab, use the arrow keys to highlight the macro number you want to delete. Press to highlight the Delete Macro button, and press . Unicode Mapping In the Keyboard Properties dialogue box, open the Unicode Mapping tab. Figure 5.12 Unicode Mapping The Unicode Mapping tab is used to map combinations of virtual key values and and states to Unicode™ values.
Chapter 5: Configuration Unicode Mapping Adding And Changing Unicode Values Important: • Changes to Unicode mappings are not saved until you exit the Keyboard Properties dialogue box. Press to highlight the Add/Change button, and press . Figure 5.13 Adding And Change Unicode Values • • Highlight the a value in the Unicode mapping list – in the sample screen above, a value will be assigned to virtual key 0 (VK 0).
Chapter 5: Configuration Volume And Sound Properties 5.5.3 Volume And Sound Properties Note: Sounds (wave files) cannot be reproduced on 7535 units. The conditions under which 7535s emit sounds are tailored from within the application installed on your unit. • In the Control Panel, choose the Volume & Sounds icon. Figure 5.14 Choosing The Volume Icon 5.5.3.1 Volume Adjustments Figure 5.
Chapter 5: Configuration Power Management Properties 5.5.4 Power Management Properties This icon displays a Power Properties dialogue box that indicates the unit’s battery capacity and allows you to manage battery use. • In the Control Panel, choose the Power icon. Figure 5.16 Choosing The Power Icon 5.5.4.1 • Battery Capacity In the Power Properties dialogue box, open the Battery tab. Figure 5.17 Power Battery Properties The Battery tab details information about the battery installed in your 7535.
Chapter 5: Configuration Power Saving Schemes 5.5.4.2 • Power Saving Schemes In the Power Properties dialogue box, open the Schemes tab. Figure 5.18 Power Scheme Properties Power Scheme This dropdown menu allows you to specify whether the unit is using AC Power or Battery Power. Switch State To Suspend Important: Psion Teklogix recommends setting the Suspend value to 10 minutes. Setting ‘Switch State To Suspend’ to ‘Never’ will adversely affect the battery run time.
Chapter 5: Configuration Suspend Threshold 5.5.4.3 • Suspend Threshold In the Power Properties dialogue box, open the Suspend Threshold tab. Figure 5.19 Suspend Threshold Properties Suspend Threshold The sliding bar in this tab is used to set the battery capacity (as a percentage value) at which the hand-held will be forced into a suspend state.
Chapter 5: Configuration Charger Details 5.5.4.4 • Charger Details In the Power Properties dialogue box, open the Charger tab. When the 7535 is in a Combo Dock, enabling (√) Allow Battery Calibration in this tab allows a battery requiring recalibration to be fully discharged and recharged. Recalibration occasionally extends the battery charge time. If you prefer that the battery always be charged in the shortest time possible, do not check this box. 5.5.
Chapter 5: Configuration Setting Double-Tap Sensitivity 5.5.5.1 • Setting Double-Tap Sensitivity In the Double-Tap tab, follow the directions to tailor the sensitivity of the stylus when you tap on the touchscreen. Figure 5.21 Setting Stylus Sensitivity 5.5.5.2 Touchscreen Calibration Touchscreens rarely require recalibration. However, if your touchscreen has never been calibrated or if you find that the stylus pointer is not accurate when you tap on an item, follow the directions below.
Chapter 5: Configuration Certificate Assignment 5.5.6 Certificate Assignment • In the Control Panel, choose the Certificate icon. The dialogue box is used in conjunction with 802.1x authentication to enhance 7535 security. Figure 5.23 Certificates Dialogue Box For a detailed description about Certificate setup for both the server and client-side devices (7535s), refer to the following website: www.microsoft.com/windows2000/techinfo/planning/walkthroughs/default.
5.7 Scanner Properties Setup The Teklogix Scanners icon in the Control Panel provides dialogue boxes in which you can tailor bar code options and choose the bar codes your scanner will recognize. 5.7.1 Scanner Options Figure 5.45 Bar Code Options To display the sub-menus available in the Options tab: • Highlight the option you want to work with, and press the right key. To change a parameter: • Highlight the parameter and press the arrow key, or press the key.
Chapter 5: Configuration Scanner Options Scan Indicator When this parameter is enabled (set to ‘ON’), the laser warning logo appears on the display whenever the scanner is activated. Scan Result Time (sec) The value assigned to the “Scan Result Time (sec)” parameter determines how long the scan results of a successful scan are displayed on the screen. Time is measured in seconds, and a value of “0” (zero) disables the parameter.
Chapter 5: Configuration Scanner Options Click Data For both integrated and external scanners, this parameter determines which character is sent to the application installed in your 7535 following a double-click. A dialogue box appears, asking that you press the key you want to insert. The ASCII/Unicode key value of the keypress is displayed. Pressing the key in this dialogue box resets the data to zero.
Chapter 5: Configuration Bar Codes 5.7.2 Bar Codes Figure 5.46 Bar Code Selection All the available bar code symbologies can be selected from this menu. Important: To improve the decode speed and performance, enable (set to ‘ON’) only those codes that are required by the application. Keep in mind that some bar code types are only available when an internal imaging scanner is installed. The bar code settings do not affect the operation of internal or external decoded scanners.
Chapter 5: Configuration Code 39 Settings Figure 5.47 Code 39 Bar Code Settings A ‘plus’ sign (+) to the left of the each bar code listed in this Barcodes tab indicate that that a sub-menu of parameters is attached. To work with a sub-menu: • • • Highlight the bar code you want to work with, and press the arrow key to display the sub-menu. Use the and arrow keys to highlight a parameter. To change a parameter value, press or the arrow key.
Chapter 5: Configuration Code 39 Settings AIAG Strip If this parameter is enabled (set to ‘ON’), the AIAG data identifier is removed from each decoded Code 39 label. The data identifier occurs in the first position next to the Code 39 start character. It can be a single alphabetic character or a series of numeric digits followed by an alphabetic character. This identifier defines the general category or specific use of the data contained in the rest of the bar code.
Chapter 5: Configuration Code 128 Settings Prefix Char This character, if non-zero, is added before a successfully decoded bar code. Press the key you want to insert in the dialogue box attached to this parameter. The ASCII/Unicode key value of the keypress is displayed. Pressing the key in this dialogue box resets the data to zero. Suffix Char Note: The appended character is treated as any other keyboard character. For example, if is pressed, the usual action for that key is performed.
Chapter 5: Configuration EAN 13 Settings Variations When using Code 128, you can choose the variation or type of bar code variation the scanner will recognize. The options available are Standard, UCC and EAN/UCC. These options are described below. Standard Enable (set to ‘ON’) “Standard” if Code 128 is desired. UCC 128 “UCC” is a variation of Code 128. EAN/UCC 128 To successfully scan this type of bar code, “EAN/UCC” must be enabled (set to ‘ON’).
Chapter 5: Configuration EAN 8 When “Addendum” is set to Disabled, the scanner does not recognize an addendum. If this parameter is set to Optional, the scanner searches for an addendum and if one exists, appends it to the main bar code. When the parameter is set to Required, the scanner does not accept the main bar code without an addendum. Prefix/Suffix Prefix Char This character, if non-zero, is added before a successfully decoded bar code.
Chapter 5: Configuration UPC And EAN Settings Addendum Important: Before “Addendum” can take effect, the “Short Code” parameter in the Options menu (see page 120) must be enabled (set to ‘ON’). Refer to “Addendum” on page 125. Prefix/Suffix See “Size/Chars” beginning on page 126. 5.7.2.5 UPC And EAN Settings Field Size/Char Refer to page 123 for details. 5.7.2.
Chapter 5: Configuration Codabar Include Number Sys If this parameter is enabled (set to ‘ON’), the number system digit is included with the decoded bar code data. Include Check When enabled (set to ‘ON’), the check digit is included with the decoded bar code data. Addendum Important: Before “Addendum” can take effect, the “Short Code” parameter in the Options menu (see page 120) must be enabled (set to ‘ON’). Refer to “Addendum” on page 125. Prefix/Suffix Refer to page 126 for details. 5.7.2.
Chapter 5: Configuration Interleaved 2 of 5 Field Size/Chars Refer to page 123 for details. 5.7.2.11 Interleaved 2 of 5 Mod 10 Chk If this parameter is enabled (set to ‘ON’), the Mod 10 check digit is calculated. This calculation is the same as the Code 39 Mod 10 check digit. ITF Chk If this parameter is enabled (set to ‘ON’), the ITF-14/16 Mod10 check digit is calculated. Include Check If this parameter is enabled (set to ‘ON’), the check digit is included with the decoded bar code data.
Chapter 5: Configuration IATA 2 of 5 ITF Check If this parameter is enabled (set to ‘ON’), the ITF-14/16 Mod10 check digit is calculated. Include Check If this parameter is enabled (set to ‘ON’), the check digit is included with the decoded bar code data. Field Size/Chars Refer to page 123 for details. 5.7.2.14 IATA 2 of 5 Mod 10 Check If this parameter is enabled (set to ‘ON’), the Mod 10 check digit is calculated.
Chapter 5: Configuration Postal: PlaNET 5.7.2.18 Postal: PlaNET Size/Chars Refer to page 123 for details. 5.7.2.19 Postal: PostNET Size/Chars Refer to page 123 for details. 5.7.2.20 Postal: Royal Mail Size/Chars Refer to page 123 for details. 5.7.2.21 2D DataMatrix Inverse Video If enabled (set to ‘ON’), this parameter allows symbols that contain light cells on a dark background to be decoded.
Chapter 5: Configuration 2D Micro PDF-417 5.7.2.24 2D Micro PDF-417 Field Size/Chars Refer to page 123 for details. 5.7.2.25 2D QR Code Inverse Video If enabled (set to ‘ON’), this parameter allows symbols that contain light cells on a dark background to be decoded. Field Size/Chars Refer to page 123 for details. 5.7.2.26 2D RSS Code Field Size/Chars Refer to page 123 for details. 5.7.2.27 Aztec Field Size/Chars Refer to page 123 for details. 5.7.3 Translations Figure 5.
Chapter 5: Configuration Translations Figure 5.49 Translation Dialogue Box Input This value is compared with the decoded bar code reading. If there is a match, the “Output” string is translated into the decoded bar code. Output If there is a match between the decoded bar code and the corresponding “Input” string, the decoded bar code will be translated into the “Output” string. This string entry parameter can be null, or it may contain any combination of standard and special characters (e.g.
Chapter 5: Configuration SNMP (Simple Network Management Protocol) Setup 5.8 SNMP (Simple Network Management Protocol) Setup Simple Network Management Protocol (SNMP) is the protocol used to monitor and manage devices attached to a TCP/IP network (providing they support SNMP). SNMP uses Management Information Bases (MIBs) that define the variables an SNMP Network Management Station can access. Each product has a defined set of MIBs that determine how SNMP operates, the type of access allowed and so on.
Chapter 5: Configuration Contact Tab 5.8.1 Contact Tab The SNMP dialogue box is displayed. Figure 5.51 Contact Tab Contact This field identifies the contact person for this managed node along with information about how to get in touch with this person. The content of this parameter is accessible through MIB-II’s sysContact object. Location This parameter is used to identify the physical location of this node (e.g., Warehouse A: Pillar 32B).
Chapter 5: Configuration Communities Tab 5.8.2 Communities Tab Figure 5.52 Community Settings The “Communities” tab provides a means of limiting access to SNMP managed devices to those SNMP Managers with matching “community names”, as specified by RFC 1157. Enable SNMP Enabling (√) ‘Enable SNMP’ allows the device to respond to SNMP queries and to send Traps. After enabling this option and rebooting the device, the SNMP Agent will automatically start up.
Chapter 5: Configuration Adding A Community 5.8.2.1 • Adding A Community Choose the Add button to add a new ‘community’. Figure 5.53 Adding A Community Name The value assigned here is the name assigned by the network administrator to the set of devices to which this managed node belongs.
Chapter 5: Configuration Modifying A Community Setting 5.8.2.2 Modifying A Community Setting To modify an existing community: • • Highlight the community you want to alter. Choose the Change button. Figure 5.54 Changing Or Removing A Community A Modify Community dialogue box is displayed, listing the community you highlighted. • 5.8.2.3 Edit the Name and/or Rights, and press to save your changes.
Chapter 5: Configuration Trap Destination Tab 5.8.3 Trap Destination Tab A trap is an unsolicited report sent to SNMP Managers by the SNMP Agent running on the managed node. This option allows you to define where the report will be sent. Figure 5.55 Trap Destination Tab 5.8.3.1 Enabling Authentication TRAPS Enabling (√) ‘Enable Authentication TRAPS’ allows authorization traps to be sent when a failure is detected (e.g., an SNMP message received with a bad community name). 5.8.3.
Chapter 5: Configuration Changing A Destination 5.8.3.3 Changing A Destination To change an existing trap destination: • Highlight the destination you want to alter in the Trap Destination tab, and then choose the Change button. A dialogue box like the one displayed when you add a destination is displayed. Figure 5.57 Changing A Destination • 5.8.3.4 Make the changes to the destination, and press to save the changes.
Chapter 5: Configuration Permitted Hosts Tab 5.8.4 Permitted Hosts Tab For security reasons, the Network Administrator may want to restrict SNMP-node access to a known sub-set of SNMP Managers. This tab lists the IP addresses of all the SNMP Managers which are allowed to monitor and manage this device. If no entries are listed, the device will accept SNMP queries from any host. Figure 5.58 Permitted Hosts Tab 5.8.4.1 Adding A Host To add a new host: • Highlight the Add button, and press .
Chapter 5: Configuration Changing A Host 5.8.4.2 Changing A Host To change an existing host IP address: • Highlight the IP address you want to alter in the Permitted Hosts tab, and then choose the Change button. A dialogue box like the one displayed when you add a host is displayed. • Make the necessary changes, and press .
TEKTERM APPLICATION 6 6.1 The Tekterm Application . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 6.2 Additional Keyboard Functions . . . . . . . . . . . . . . . . . . . . . . . 147 6.2.1 Function Keys And Softkeys. . . . . . . . . . . . . . . . . . . . . . 147 6.2.1.1 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . .147 6.2.1.2 Softkey Function Keys . . . . . . . . . . . . . . . . . . . . .148 6.2.2 Macro Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 6.
6.6.4 Block Mode (Local Editing) . . . . . . . . . . . . . . . . . . . . . .164 6.6.5 Working With Sessions . . . . . . . . . . . . . . . . . . . . . . . . .165 6.6.5.1 Establishing A New Session . . . . . . . . . . . . . . . . . 165 6.6.5.2 Listing Sessions And Moving To Other Sessions. . . . . . . 165 6.6.5.3 Closing A Session . . . . . . . . . . . . . . . . . . . . . . . 165 6.6.5.4 Printing A Screen . . . . . . . . . . . . . . . . . . . . . . . 166 6.6.5.5 Smart Echo – Disabling . . . . . . . . . . . .
Chapter 6: Tekterm Application 6.16 Scanner Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 6.17 View Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 6.17.1 Split Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 6.17.1.1 Splitting And Displaying Screens. . . . . . . . . . . . . . .189 6.17.1.2 Moving Between Split Screens . . . . . . . . . . . . . . . .190 6.17.1.3 Toggling Between Full & Split Screens . . . . . . . . . . .190 6.17.
Chapter 6: Tekterm Application The Tekterm Application 6.1 The Tekterm Application Tekterm is a powerful emulation application ideally suited for real time data transaction applications associated with mainframes and servers. The 7535 includes unique features that support Tekterm – a Psion Teklogix application that has the ability to maintain multiple simultaneous sessions with a variety of host computers. 6.
Chapter 6: Tekterm Application Softkey Function Keys Additional function keys – to – are colour coded in orange print above function keys to . To access function keys to : • Press the key followed by the appropriate function key. For example: To access function key , press the key followed by . To access function key , press followed by , and so on.
Chapter 6: Tekterm Application Macro Keys SAVE – Saves a change to a parameter value. LITRL – Literal mode allows special characters to be entered in a string parameter such as macro key strings. Table 6.1 Softkeys Note: The SAVE onscreen label only appears when a parameter value has been changed and has not yet been saved. 6.2.2 Macro Keys Important: Refer to “Keyboard Macro Keys” on page 95 for details about creating macros.
Chapter 6: Tekterm Application Keyboard Modes Macro keys to are colour coded in blue print above macro keys and . • To access , press the key followed by . • To access , press . 6.3 Keyboard Modes 6.3.1 View Mode Placing the 7535 keyboard in View mode allows you to choose another screen font and to pan the contents of the screen. To place the computer keyboard in View mode: • Press .
Chapter 6: Tekterm Application Exiting View Mode Panning relies on the values set in the “Use Increment”, “X Increment” and “Y Increment” parameters to determine the number of columns (spaces) and rows (lines) the screen contents shift. • • In the “More Parameters” menu, position the cursor on “View Manager” and press . First, enable the “Use Increment” parameter – set it to “Y”.
Chapter 6: Tekterm Application Using The Task Manager To Switch Between Applications 6.3.2 Using The Task Manager To Switch Between Applications To display the Task Manager screen: • • • Press <0> to display the Start Menu. Highlight Task Manager, and press , or Just type the underlined alpha character – in this case, the letter ‘t’. Figure 6.1 Task Manager Screen Note: A shortcut – to bypass the Start Menu and go directly to the ‘Task Manager’ screen, press .
Chapter 6: Tekterm Application The Tekterm Status Area 6.4 The Tekterm Status Area Tekterm provides a status area just above the softkey labels. The status area indicates the operating condition of the hand-held. Figure 6.2 Status Area Table 6.2 outlines the options displayed in the status area. Status Area Indicators Security Level The security level assigned within the Tekterm application is displayed in the Within Tekterm status area. One of the following is displayed – User, Supervisor or Teklogix.
Chapter 6: Tekterm Application TESS Emulation 6.5 TESS Emulation TESS (Teklogix Screen Subsystem) is the normal operating mode of Psion Teklogix computers. Teklogix protocol emulation software resident on network controllers or a Psion Teklogix Software Development Kit (SDK) and installed in the host converts host screens to TESS commands. The 9150 Access Point is also equipped with protocol emulation software.
Chapter 6: Tekterm Application IBM 5250 Emulation Keys Auto-tab Field – automatically moves the cursor to the next field when the current field is filled. Bar code only Field – is filled with data from a bar code reader. Keyboard entries are not accepted in this type of field. Serial I/O Field – is filled with data coming from a serial port. Keyboard input is not accepted in this type of field. 6.5.
Chapter 6: Tekterm Application TESS Edit Modes And Cursor Movement There are several ways to configure the 7535 hand-held to complete a data field: • • • • Pressing after entering data. Pressing a function key after entering data. Pressing an arrow key after entering data. Filling an auto-tab field. 6.5.5.1 TESS Edit Modes And Cursor Movement The TESS editing modes and cursor movements in each type of mode are described in the table below.
Chapter 6: Tekterm Application Key Behaviour In TESS 6.5.5.2 Key Behaviour In TESS Field mode Replace mode Insert mode Fcursor mode • In a left justified field, the key erases all characters in the field and places the cursor in the left most position of that field. • In a right justified field, the key erases all characters in the field and places the cursor in the right most position of that field.
Chapter 6: Tekterm Application Key Behaviour In TESS 6.5.5.3 Key Behaviour In TESS Field mode Replace mode • In a left justified field, the key erases the character directly to the left of the cursor and then moves the cursor one position to the left. When the last character in the field is deleted, the field displays the value that it contained before it was modified, and the field is opened.
Chapter 6: Tekterm Application TESS Status Message Insert mode • In a left justified field, the function erases the character on which the cursor is positioned, unless it is at the right end of the character string; in this case, it erases the character to the left of the cursor. When the last character in a field is erased, the field remains empty, and any further functions in the empty field result in a keyboard error beep.
Chapter 6: Tekterm Application Lock Messages 6.5.7 Lock Messages When information is transmitted to the host computer, the keyboard locks to prevent further data entry until the 7535 receives a reply. A locked state is indicated by either “LOCK-B” (base) or “LOCK-H” (host) in the lower left corner of the display. When the reply is received by the 7535, the lock message disappears and the keyboard can be used again. 6.5.
Chapter 6: Tekterm Application The Local Menu 6.5.10 The Local Menu The host can store local procedures in the 7535 for use when the unit is off-line. A menu of these procedures appears whenever is pressed (see Figure 6.3). • Press the function key corresponding to the procedure you want to perform. Local procedures will not function when the “Lcl Process” and “Queuing” parameters are disabled (see “Lcl Process – Save on Reset” on page 219 and “Queuing” on page 219).
Chapter 6: Tekterm Application Queuing Mode 6.5.12 Queuing Mode In some applications, queuing mode can decrease the computer lock time. In queuing mode, the host computer may send several pages to a 7535 without waiting for a response. These pages are stored in a queue within the 7535 hand-held. The operator completes the entries on the first page and then, presses a function key. The 7535 simultaneously transmits to the host and displays the next page in the queue.
Chapter 6: Tekterm Application Sending Data To The Host 6.6.2 Sending Data To The Host 7535 hand-helds running ANSI sessions transmit characters to the host as soon as they are typed. The 7535 provides parameters that determine when the computer transmits characters to the host. The 7535 can be configured to transmit after a number of characters are typed in (the “Xmit Count” parameter) or after some time has elapsed (the “Xmit Wait” parameter), or both.
Chapter 6: Tekterm Application Block Mode (Local Editing) Psion Teklogix Key - Equivalent VT220 Key Find Insert Here Remove Select Previous Screen Next Screen None Table 6.3 Psion Teklogix Keyboard And VT220 Equivalent Keys 6.6.4 Block Mode (Local Editing) The Psion Teklogix 7535s support “block mode” (or Local Editing). Application programs must be specifically written to support this mode. For software that supports this mode, the keys shown in Table 6.
Chapter 6: Tekterm Application Working With Sessions 6.6.5 Working With Sessions Important: Use only lowercase letters when entering commands at the “TCP >” prompt. 6.6.5.1 Establishing A New Session • Press , and type a lowercase a. At the TCP> prompt: • Type tel in lowercase letters followed by the Host Name or IP address. • Press . • Log in as usual to begin working with the new session. 6.6.5.
Chapter 6: Tekterm Application Printing A Screen 6.6.5.4 Printing A Screen To print each line of a screen with a CR/LF between each line: • Press , and type p. The screen will be printed using the port configured as “Print”. 6.6.5.5 Smart Echo – Disabling In some circumstances – like entering a password – you many want to temporarily disable “smart echo”, disguising the characters you type with ‘.’ (periods). • Press , and type a ‘.’ (period).
Chapter 6: Tekterm Application The Radio Statistics Screen 802.IQ Stats Screen 802.IQ Stats AP/Controller MAC 00:00:00:00 Terminal MAC 00:00:00:00:00:00 bootnum: C33B rm 12 xm 7 rb 50 xi 1 ra 7 xa 12 bt 0 xr 1 rt (avg/lst) 10000: 0 fr:00 ar:00 fh:00 ah:00 ca:0 tn:0 sts:0 typ:0 msk:0 Q:0 AcQ:1 TxQ:1 -----Address Info------------Radio Address 0 End of statistics. • AP/Controller mac • MAC address of the Teklogix access point/controller with which this 7535 is currently associated.
Chapter 6: Tekterm Application The Tekterm Startup Display Menu • xr • rt number of retransmissions. This number should remain low if radio coverage is adequate. average round trip time. This number represents the milliseconds taken to send a message and receive a response from the base station. Cellular Protocol message numbers: • • • • • fr ar fh ah ca • • • • • tn sts typ msk Q • AcQ • TxQ forward remote number (hex). acknowledged remote number (hex). forward host number (hex).
Chapter 6: Tekterm Application Working With Menus From this startup menu, you can launch the “Parameters” menu along with TESS and/or ANSI sessions. You can also display the Radio Statistics screen. 01 A B C Display Menu Parameters TESS ANSI Note: Aside from the ‘Parameters’ menu, all other applications listed in the ‘Display Menu’ are created in the ‘Applications’ menu. Refer to “Applications” on page 194 for details.
Chapter 6: Tekterm Application Using The Keyboard To Navigate Through Menus 6.9.1 Using The Keyboard To Navigate Through Menus • Press the and arrow keys to move the cursor up and down the current menu. The currently selected parameter name will be displayed in reverse video. 6.9.1.1 Sub-Menus The “»” character appearing to the right of the menu item indicates that it has a sub-menu.
Chapter 6: Tekterm Application Y/N Parameters 6.9.1.3 Y/N Parameters Y/N parameters can only be enabled (Y) or disabled (N). To enable or disable a Y/N parameter: • • Press the or arrow key once, or Type y to enable or n to disable the parameter. Some Y/N parameters have sub-menus. For these parameters, a double right arrow (») appears next to the “Y” or “N”. 6.9.1.4 Alpha Parameters Alpha characters appear in reverse video in this type of parameter.
Chapter 6: Tekterm Application String Entry Parameters Choosing An ASCII Character With The Arrow Keys Important: Make sure the and keys are turned off! By pressing either the or arrow key, you can cycle through a set of printable characters not directly accessible from the keyboard. • Press the arrow to display the next character in this sequence, and the arrow to display the previous one.
Chapter 6: Tekterm Application Using The Touchscreen To Navigate Through Menus Entering Unicode Values Unicode is a trademark of The Unicode Consortium. To enter a Unicode™ value for one-time use: • Press and hold down the key while typing a four digit decimal value that represents the Unicode™ character you want to display. • Release the key.
Chapter 6: Tekterm Application Numeric Parameters 6.9.2.2 Numeric Parameters Numeric parameters are displayed in reverse video. • • To decrease the numeric value, tap the stylus on the left side of the number. To increase the numeric value, tap the stylus on the right side of the number. Each numeric parameter has a preset range of numbers assigned to it – for example, a preset range of 1 through 10.
Chapter 6: Tekterm Application Saving Changes To Parameters 6.9.3 Saving Changes To Parameters Whenever a parameter value is altered, the new value must be saved. To do this: • Press – the “SAVE” key. If you are using a touchscreen: • Tap the stylus on the “SAVE” softkey label. • If the softkey labels are not visible, you’ll have to press – the “SAVE” function key.
Chapter 6: Tekterm Application The Parameters Menu 6.11 The Parameters Menu • At the ‘Display’ menu, type a to display the Parameters menu. 01 Parameters More Parameters Security Display » User » Range see page 177 see page 176 see page 177 The “Parameters” menu allows you to adjust the screen contrast and select a security level. With a Supervisory or Teklogix password, you can also access the parameters listed in the “More Parameters” sub-menu. 6.11.
Chapter 6: Tekterm Application Display Options 6.12 Display Options The ‘Display’ sub-menu is used to adjust your unit’s display properties. • Press to access the ‘Display’ sub-menu. 02 Display Backlight Ctrl Panel » Contrast Ctrl Panel » Range see text see text The Display Properties dialogue box is displayed where you can adjust the appearance, backlight and contrast of your 7535 display. Important: ‘Display Properties’ dialogue box options are described in detail beginning on page 88. Figure 6.
Chapter 6: Tekterm Application More Parameters Note: Parameters can also be remotely modified using SNMP. Refer to “SNMP (Simple Network Management Protocol) Setup” on page 134 for details. • At the startup ‘Display’ menu, type ‘a’ to display the ‘Parameters’ menu. 01 Parameters More Parameters Security Display • » Supervisor » Range see page 177 see page 176 see page 177 To open the ‘More Parameters’ menu, press .
Chapter 6: Tekterm Application Radio Parameters 6.14 Radio Parameters Important: Radio parameters should not be changed from their factory settings without a clear understanding of your system. The 7535 is equipped with an Intel 802.11b radio. • Press to display the ‘Radio’ sub-menu. 03 Radio 802.11 » • Press to access the ‘802.11’ sub-menu. 04 802.11 DS SS 802.IQ v1 N » • Set ‘802.IQ v1’ to ‘Y’ to activate these parameters. and press to display ‘802.IQ v1’ parameters. Range 05 802.
Chapter 6: Tekterm Application System Parameters Radio Address The value entered in the “Radio address” parameter is used to identify the 7535 over the radio link. A unique value from 1 to 3840 must be assigned for each 7535 hand-held computer. Initial RTT (Round Trip Time) Round trip time is the elapsed time between a hand-held computer transmission and an access point acknowledgement.
Chapter 6: Tekterm Application Keyboard 6.15.1 Keyboard Keyboard 04 Macro Ctrl Panel Indicators Softkeys Ctrl Panel » Y Y » 6.15.1.1 Macro Control Panel • Highlight ‘Macro Ctrl Panel’, and press to display the Macros tab in the Keyboard Properties dialogue box. Figure 6.6 Macro Dialogue Box Important: Refer to “Keyboard Macro Keys” on page 95 for detailed instructions about creating macros. Important: For information about using the macro keys you’ve created, refer to “Macro Keys” on page 149.
Chapter 6: Tekterm Application Indicators 6.15.1.2 Indicators When the “Indicators” parameter is enabled (set to “Y”), onscreen indicators are displayed to indicate the operating condition of the 7535. Refer to “Onscreen Indicators” on page 45 for a list of possible indicators. 6.15.1.3 Softkeys Enabling (setting to “Y”) the “Softkeys” parameter displays softkey labels at the bottom of the screen to indicate the function of each softkey. To block the display of softkey labels, set this parameter to “N”.
Chapter 6: Tekterm Application Audio 6.15.
Chapter 6: Tekterm Application Power Mgmt Ctrl Panel Sounds Ctrl Panel This option displays the Volume & Sounds Properties dialogue box. Figure 6.8 Adjusting The Volume This dialogue box is used adjust the beeper volume and to select the conditions under which the 7535 will emit a beep. Important: Refer to “Volume And Sound Properties” on page 99 for details about this dialogue box. 6.15.3 Power Mgmt Ctrl Panel This menu item displays the Power Properties dialogue box. Figure 6.
Chapter 6: Tekterm Application Security 6.15.4 Security 04 Security Default mode User Sup. password Allow Teklogix Range Supervisor, Teklogix see text see text Y/N User » ###### Y 6.15.4.1 Default Mode The value assigned to this parameter determines the operator’s level of access to 7535 parameters. The allowable values are User, Supervisor and Teklogix. “Default mode” is set to User. At User level, the operator is restricted to a small group of parameters. These are listed in the “User” sub-menu.
Chapter 6: Tekterm Application Sup. Password Font Chg When “Font Chg” is set to “Y”, operators at the User level can change the font size of their 7535s. 6.15.4.3 Sup. Password Note: Only a Supervisor or Teklogix level password can change the Supervisor password. The supervisory password is set at the factory to 123456. You should change the default password to better protect the 7535 settings. When you’ve changed the password, write down the new password and file it in a secure place.
Chapter 6: Tekterm Application Scanner Control Panel 6.16 Scanner Control Panel This menu item displays a Scanner Properties dialogue box in which you can set up the particulars of your unit’s scanner performance, choose the bar codes which will be decoded, and so on. Figure 6.10 Scanner Properties Dialogue Box Important: Refer to "Scanner Properties Setup" beginning on page 118 for details about setting up your scanner. 6.
Chapter 6: Tekterm Application Split Screen Block Cursor When this parameter is enabled (set to “Y”), the cursor is presented as a flashing block. When “Block Cursor” is set to “N”, the cursor is presented as a flashing underline character. Use increment When “Use increment” is enabled (set to “Y”) and the cursor is moved off the display, the screen contents shift by the values specified in the “X-increment” and “Y-increment” parameters.
Chapter 6: Tekterm Application Splitting And Displaying Screens 6.17.1.1 Splitting And Displaying Screens Before splitting the screen, you need to determine which applications should appear in each pane of the split screen. The available applications are listed in the main “Display Menu”. Each application listed in the “Display Menu” is preceded by a letter – for example, Parameters is preceded by an A.
Chapter 6: Tekterm Application Moving Between Split Screens 6.17.1.2 Moving Between Split Screens To move the cursor from one pane in a split screen to the next: • Press or . The cursor moves in order from the left-most pane to the right and from the top-most pane to the bottom. 6.17.1.3 Toggling Between Full & Split Screens To toggle between a split and full screen format: • Press arrow.
Chapter 6: Tekterm Application Custom Characters (Unicode™) 6.17.2 Custom Characters (Unicode™) Note: The Unicode ™ characters created here are accessible only within the Tekterm application. To create Unicode ™ characters that are accessible system-wide, refer to “Unicode Mapping” on page 97. The “Custom Characters” parameter allows you to create Unicode™ characters not available directly from the keyboard, including accented characters. Unicode is a trademark of The Unicode Consortium.
Chapter 6: Tekterm Application Displaying The Unicode™ Pop-up Window • Press the arrow key to accept the value and move the cursor to the next field. When you have finished creating the Unicode™ characters you want to use: • • Press to save your changes. Reset the 7535 – press and hold down the and key simultaneously for a minimum of six seconds. 6.17.2.
Chapter 6: Tekterm Application Displaying The Unicode™ Pop-up Window Font Override Font Override 04 Font Code 0 ... is font 18x32 Font Code 1 ... is font 18x32 Font Code 2 ... is font 10x26 Font Code 3 ... is font 18x32 Font Code 4 ... is font 8x20 This parameter is used to redefine the font to which 5 different font codes refer.
Chapter 6: Tekterm Application Applications 6.18 Applications “TESS” and “ANSI” applications require unique names so that several different sessions of “TESS” and “ANSI” can operate simultaneously. 7535s can support up to 8 sessions at one time. 03 Applications Type1 #1 ANSI Title1 #1 parts Settings 1 » . . .
Chapter 6: Tekterm Application ANSI Settings 6.18.1 ANSI Settings Ansi 04 Auto Term # Terminal # Host Conn Screen Xmit Modes Kbd Modes Edit Modes Serial Host Char Set Anchor View N» 1 » » » » » » » N» Range see text 1..1024 see text see text see text see text see text see text see text see text Each session you create has its own “Settings” parameters. Additional ANSI information is documented in “ANSI Emulation” on page 162. Auto Term# Note: Refer to “Group” on page 195 for additional instructions.
Chapter 6: Tekterm Application Host Conn Other applications running in the 7535, such as a TESS session or another ANSI session must each have a different number. In addition, each Psion Teklogix 7535 using the radio link must have a unique number. 6.18.1.1 Host Conn Host Conn Conn Type Telnet Settings » Range 802.
Chapter 6: Tekterm Application Host Conn Host This parameter is used to assign a host IP address using the format ###.###.###.### or a host name if DNS is used. Port “Port” specifies the 9010t (TCP Direct) or Telnet port number. The default 9010t port number assigned is 9999, the maximum allowable value. The default Telnet port number assigned is 23 with a maximum allowable value of 32767.
Chapter 6: Tekterm Application Host Conn Login Prompt When the terminal receives the string assigned to this parameter, it will respond with “Login”. Login The terminal responds with this string when it receives a “Login Prompt”. Password Prompt When the terminal receives this string, it responds with a “Password”. Password The terminal responds with this string when it receives a “Password Prompt”.
Chapter 6: Tekterm Application Screen To change values: • Press the or arrow key to highlight a function key. • Press the key to move through the string of values. • Either type new values, or press the or arrow key to change the values. 6.18.1.2 Screen Screen 05 # of Pages # of Rows # of Cols Default Font 80-col. Font 132-col. Font Video Label F1-F6 Colour override 4 24 80 16x30 16x30 16x30 » » N» Range 0..16 4..
Chapter 6: Tekterm Application Screen # of Cols This parameter defines the logical page width (in characters) used by the host computer application. Emulator systems trim the host application screens to this width. This page width cannot be smaller than the width of the display. Display panning is used if the page is wider than the display. Note: The value in this parameter must be an even number. Default font This parameter determines the default font that appears when the 7535 memory is reset.
Chapter 6: Tekterm Application Screen Blink This parameter specifies the actual video attributes to be assigned to fields created with the “Blink” ANSI attribute. Reverse This parameter specifies the actual video attributes to be assigned to fields created with the “Reverse” ANSI attribute. Underline This parameter specifies the actual video attributes to be assigned to fields created with the “Underline” ANSI attribute. Label F1-F6 Note: This menu uses string entry fields.
Chapter 6: Tekterm Application Xmit Modes Colour Override Note: This menu is available only if the 7535 is equipped with a colour display. 06 Colour Override Foreground Black Background White Range see text see text Foreground And Background When “Colour Override” is set to ‘Y’, the colours chosen in this menu are displayed in the ANSI sessions. These colour settings will override the “Default Colours” set from within the “View Manager” menu. Refer to “Default Colours” on page 193 for details.
Chapter 6: Tekterm Application Xmit Modes Xmit Wait This parameter determines the length of time the 7535 collects keystrokes before transmitting them to the host. This value is specified in increments of one 10th of a second (i.e., a value of 10 represents 1 second). If 0 (zero) is selected, the computer transmits only according to the “Xmit Count” parameter.
Chapter 6: Tekterm Application Xmit Modes Block Mode 06 Block Mode Kbd lock N Xmit key N FETM N GATM N MATM N SATM Y TTM Y EOL chars EOB chars All modes in this section affect the data stream sent to the host computer, the serial port and the console port. These modes apply to the Block mode (Local Editing) and the Media Copy function, unless otherwise noted. Consult the Teklogix ANSI Terminal Programmer’s Manual for more information.
Chapter 6: Tekterm Application Xmit Modes GATM When the Guarded Area Transfer Mode (GATM) parameter is disabled (set to “N”), only unguarded data is transmitted to the host or transferred to the console or serial ports. When enabled (set to “Y”), both guarded and unguarded data can be transmitted to the host or transferred to the console or serial ports.
Chapter 6: Tekterm Application Kbd Modes 6.18.1.4 Kbd Modes 05 Kbd Modes Arrow mode Echo mode BKSP key PrintScreen key Xmit Enter Insert Newline Disable kbd DEC Cursor Keys cursor Smart DEL 16 Y N N N cursor mode Range cursor, field Smart, Local, Host DEL, BS 1..255 Y/N Y/N Y/N Y/N see text Arrow mode This parameter determines whether arrow keys move the cursor within a field or between fields.
Chapter 6: Tekterm Application Kbd Modes The maximum number of characters waiting for echo is 25. Any additional characters are sent to the host but not displayed. When the 7535 is in insert mode, smart echo is disabled. Key Function ENTER In newline mode, this key moves the cursor to the first column of the next line. In line feed mode, this key moves the cursor to column one of the current line. CTRL-G (Bell) The 7535 beeps. CTRL-H (Backspace) The cursor moves back one space.
Chapter 6: Tekterm Application Kbd Modes Xmit Enter The key normally enters data into a field and moves the cursor to the next field. However, some applications require that the key start a transmission from the 7535. When enabled (set to “Y”), this parameter causes the key to start a transmission.
Chapter 6: Tekterm Application Edit Modes 6.18.1.5 Edit Modes 04 Edit Modes Auto wrap Erasure mode Tab stop mode Edit extent Disp controls N N N Line N Range Y/N Y/N Y/N see text Y/N Auto wrap If “Auto wrap” is disabled (set to “N”), characters received when the cursor is at the right edge of the screen replace the previously displayed characters. If “Auto wrap” is enabled (set to “Y”), the cursor wraps to the next line when the current line is filled.
Chapter 6: Tekterm Application Serial 6.18.1.6 Serial 05 Serial Primary Port Secondary Port Async In Start End Any Available Any Available N 0 0 Range see text see text Y/N 0..255 0..255 Primary Port & Secondary Port ANSI print commands (such as ‘MC’ or Media Copy) control the transfer of data to and from the serial and console ports on the 7535.
Chapter 6: Tekterm Application Anchor View To choose ‘Lower’ and ‘Upper character sets: • • Position the cursor on the ‘Lower’ or ‘Upper’ parameter, and press the or arrow key to display the character set options. Press to save your selection to memory. Important: When a character sent from the host cannot be displayed, a rectangular box is used as a substitute. 6.18.1.8 Anchor View 05 Anchor x origin y origin 1 1 Range 1..24 1..
Chapter 6: Tekterm Application TESS Settings 6.18.2 TESS Settings TESS 04 Auto Term # Terminal # Host Conn Screen Characters Tests Features Scanner Fields Anchor View Emulation Range N» 1 » » » » » » » N» » see see see see see see see see see see text text text text text text text text text text Each session you create has its own “Settings” parameters. Additional TESS information is documented in “TESS Emulation” on page 154. Auto Term# Note: “Auto Term#” is available when 802.
Chapter 6: Tekterm Application Host Conn. Terminal # For every application session you create, the “Terminal #” assigned must be nonzero and unique. This parameter defines the terminal number for the TESS session and uniquely identifies all transmissions to and from the 7535. Other applications running in the 7535, such as an ANSI session or another TESS session must each have a different number. In addition, each Psion Teklogix 7535 using the radio link must have a unique number. 6.18.2.1 Host Conn.
Chapter 6: Tekterm Application Screen 6.18.2.2 Screen 05 Screen # of Cols # of Rows Origin Scroll Field Scroll Pages Saved App. Parameter Label F1-6 Colour Override 80 24 N N 16 0 » N» Range 20..132 4..100 Y/N Y/N 1..16 -1..79 see text see text # of Cols This parameter defines the logical page width (in characters) used by the host computer application. Emulator systems trim the host application screens to this width. This page width cannot be smaller than the width of the 7535 display.
Chapter 6: Tekterm Application Screen Pages Saved This parameter determines the number of pages that can be stored and recalled at the 7535. Storing frequently used page data at the 7535 reduces the need for the host to retransmit complete page data over the radio link. Retransmitting data can reduce the system response time. Increasing the number of saved pages decreases the available memory for other functions. App.
Chapter 6: Tekterm Application Characters Colour Override Note: The menu is available only if your 7535 is equipped with a colour display. Range 06 Colour Override Foreground Black Background White see text see text Foreground And Background When “Colour Override” is set to ‘Y’, the colours chosen in this menu are displayed in the TESS sessions. These colour settings override the “Default Colours” set from within the “View Manager” menu. Refer to “Default Colours” on page 193 for details.
Chapter 6: Tekterm Application Characters To choose a character set: • Position the cursor on the appropriate item – for example, ISO – and press to display the character set options. • To activate a character set, press the or arrow key to set it to “Y”. Important: If you choose a Chinese character set from the ‘Misc.’ menu and a character sent from the host cannot be displayed on the 7535 screen, a shaded box character is used as a substitute.
Chapter 6: Tekterm Application Tests Fill Chr This parameter specifies the character that identifies empty entry fields. Enter the ASCII decimal equivalent of this character. The most commonly used characters are: _ (underline) . (period) Enter 95 Enter 46 Note: 7535s in some systems may use the “space” character with the host using reverse video attributes to mark entry fields. Upper Case When this parameter is enabled (set to “Y”), lowercase input is converted to uppercase. 6.18.2.
Chapter 6: Tekterm Application Features 6.18.2.5 Features 05 Features Printer Binary print Queuing Lcl Process Send Mile Next X Kbd Locked Remap Passthru Disable Beep Serial Y N Y Y » N N N N N » Range Y/N Y/N Y/N see text Y/N Y/N Y/N Y/N Y/N see text Printer This parameter enables and disables the pins in the serial port used for printers or other external devices.
Chapter 6: Tekterm Application Features Send Mile This parameter controls the sending of a milestone from the 7535 after a “hey_you” command. Consult the Teklogix Screen Subsystem (TESS) User Manual for more information on milestones. Next X This parameter enables and disables the next messages used in queuing mode. Kbd Locked This parameter allows you to lock (set to “Y”) or unlock (set to “N”) the keyboard for all alphanumeric input in TESS.
Chapter 6: Tekterm Application Features Serial 06 Serial Serial Port Serial Out Serial In SI mode SI prefix SI suffix SI CRC SI Fkey SO prefix SO suffix SO CRC Range Any Available see text Y Y/N N Y/N see text 10 0..255 13 0..255 N Y/N 0 0..255 10 0..255 13 0..255 N Y/N Serial Port TESS print commands control the transfer of data to and from the serial and printer ports on the 7535.
Chapter 6: Tekterm Application Features SI prefix This parameter determines the start-of-message character on serial input. Enter an ASCII numeric equivalent from 0 to 255 to represent the start character. A value of 0 (zero) indicates no prefix. SI suffix This parameter determines the end-of-message character on serial input. Enter an ASCII numeric equivalent from 0 to 255 to represent the end character. A value of 0 (zero) indicates no suffix.
Chapter 6: Tekterm Application Scanner SO CRC When this parameter is enabled (set to “Y”), a CRC16 value is appended to the serial output message. Also, when this parameter is enabled (set to “Y”), for each control character in the serial output stream, a DLE is inserted to precede that character. The control character is replaced with its 1’s complement. 6.18.2.
Chapter 6: Tekterm Application Fields Mixed AIAG When this parameter is enabled (set to “Y”), AIAG labels are always accepted and processed – even if mixed with keyboard input. The AIAG label can replace the partially entered keyboard data. If this parameter is disabled, AIAG labels are rejected if field entry is in progress. Rjct if Alpha When the cursor is in a numeric field and “Rjct if Alpha” is enabled (set to “Y”), bar codes containing alphabetic characters are rejected.
Chapter 6: Tekterm Application Fields Enter To F0 The key normally enters data into a field and moves the cursor to the next field. However, some applications require that the key start a transmission from the 7535. When enabled (set to “Y”), this parameter causes the key to be interpreted as which starts a transmission. Enter On Arr When this parameter is enabled (set to “Y”), the arrow keys can be used to complete data entry into a field.
Chapter 6: Tekterm Application Fields Default font This parameter determines the default font that appears when the memory is reset. • Use the or arrow key to scroll through the options. Entry Mode “Entry Mode” parameters allow you to select a data entry mode. The modes are: insert, replace, field and fcursor. “TESS Edit Modes And Cursor Movement” on page 156 describes these modes in detail.
Chapter 6: Tekterm Application Anchor View 6.18.2.8 Anchor View 05 Anchor x origin y origin 1 1 Range 1..24 1..80 When enabled (set to “Y”), this parameter locks the display at a defined location on the screen, preventing it from shifting when the cursor is moved. The “x origin” and “y origin” coordinates specify where the screen origin, the upper left corner of the screen, will be fixed.
Chapter 6: Tekterm Application Emulation Features – 2392/Telnet Features 06 Clear Entry Fields N Passthru Printing N AIAG Character 0 Barcode Character 0 Serial IO Character 0 Fixed Field Ovrhd 5 Enable Alarm N Command Region Up 0 Command Region Down 0 Command Region Left 0 Command Region Right 0 Range Y/N Y/N 0-255 0-255 0-255 0-80 Y/N 0-24 0-24 0-80 0-80 Clear Entry Fields When this parameter is set to ‘Y’, an empty entry field is created in place of an entry field filled with spaces.
Chapter 6: Tekterm Application Emulation This parameter is used to enter a decimal representation of the ASCII character code of the barcode-input-only character. A value of 0 (zero) disables this feature. Serial IO Character Serial I/O fields are special entry and fixed fields that accept input from and output to a serial port. The application program distinguishes this field as Serial I/O by preceding the field with a special character.
Chapter 6: Tekterm Application Emulation 3274/Telnet Emulation Emulation 05 Fujitsu Host Intl EBCDIC Nulls in Fields IP for SysReq BRK for Attn LU Name Enabled LU Name Features FKEY0-7 FKEY8-15 FKEY16-23 FKEY24-31 FKEY32-39 N N N N N N » » » » » » Range Y/N Y/N Y/N Y/N Y/N Y/N see text see text see text see text see text see text see text Fujitsu Host If this parameter is set to ‘Y’, data is sent in Fujitsu format.
Chapter 6: Tekterm Application Emulation BRK for Attn When the attention key is pressed, a Telnet “Break” command is generated. This command is sent to the host in place of the standard mechanism used to send the attention key press to a host using Telnet. LU Name Enabled If enabled (set to ‘Y’), this parameter allows the 7535 to negotiate a specific device name for itself. LU Name The value assigned in this field is used when the “LU Name Enabled” parameter (see above) is set to ‘Y’.
Chapter 6: Tekterm Application Emulation FKEY0-7, FKEY8-15, FKEY16-23, FKEY24-31 And FKEY32-39 06 FKEY0-7 FKEY0 ENTER FKEY1 F1 FKEY2 F2 FKEY3 F3 FKEY4 F4 FKEY5 F5 FKEY6 F6 FKEY7 F7 The sub-menus attached to these parameters allow you to map the 7535 function keys.
Chapter 6: Tekterm Application Emulation Remap Underline To This parameter allows you to remap the underline cursor to: blink, bold or reverse. Intl EBCDIC If this parameter is enabled (set to ‘Y’), the ‘international’ EBCDIC character set is used, swapping the positions of the ! and ] characters. Nulls In Fields Setting this parameter to ‘Y’ allows ‘null’ characters – e.g., hyphens (-) or periods (.) – to fill in empty entry fields.
Chapter 6: Tekterm Application Emulation Features – 5250/Telnet Features 06 Clear Entry Fields N Passthru Printing N AIAG Character 0 Barcode Character 0 Serial IO Character 0 Fixed Field Ovrhd 5 Enable Alarm N Command Region Up 0 Command Region Down 0 Command Region Left 0 Command Region Right 0 Range Y/N Y/N 0-255 0-255 0-255 0-80 Y/N 0-24 0-24 0-80 0-80 These parameters are identical to those described for 2392/Telnet. Refer to "Features – 2392/Telnet" beginning on page 228.
Chapter 6: Tekterm Application Ports– Tether And Console 6.19 Ports– Tether And Console 03 Ports Tether Port Settings 1 Console Port Settings 2 Console » Disabled » 6.19.1 Tether And Console Port Peripheral Options The “Tether Port” and “Console Port” options allow you to enable, disable and specify the accessories attached to these ports. Both the Tether Port and the Console Port have the same options. These are: Disabled, Serial, Console, Printer and Scan-See.
Chapter 6: Tekterm Application Tether And Console Port Parameter Settings 6.19.2 Tether And Console Port Parameter Settings The parameters for the “Tether Port” and “Console Port” are identical. Settings 04 Character Set » Baud 9600 Data Bits 8 Parity none Stop Bits 1 Flow Ctrl None Buffer 512 Retries 3 Input Tmo 2 Output Tmo 5 Test Y Range see text see text for range of baud rates 6..8 none odd even mark space 1, 1.5, 2 None Software Hardware Both 1..2048 1..100 1..100 1..
Chapter 6: Tekterm Application Tether And Console Port Parameter Settings Choosing A Character Set To choose a character set: • Position the cursor on the appropriate item – for example, ISO – and press to display the character set options. • To activate a character set, press the or arrow key to set it to “Y”. Important: If you choose a Chinese character set from the ‘Misc.
Chapter 6: Tekterm Application Tether And Console Port Parameter Settings Supports XON/XOFF or no handshaking. Print: Used to output data only. All input characters except XON and XOFF are ignored. Supports XON/XOFF or no handshaking. Output: Used to output data only. All input characters are ignored. Supports no handshaking. Note: To enable the input and/or output, ‘serial in’ and/or ‘serial out’ must be enabled in the TESS menu.
Chapter 6: Tekterm Application Tether And Console Port Scan-See Parameters 6.19.3 Tether And Console Port Scan-See Parameters When ‘Scan-See’ is specified as the peripheral for either the Tether or the Console port, the parameters listed under the “Scan-See” sub-menu are used to tailor the operation of this type of scanner. The other parameters listed in this menu – “Character Set”, “Baud” and so on – are identical to those described beginning on page 235.
Chapter 6: Tekterm Application Scan-See Sub-Menu – Mapping The Viewport The Scan-See display is mapped to a specific area on the 7535 screen – called the viewport – and is continuously updated to reflect that portion of the screen. The Scan-See viewport is defined as follows: Anchor Line/Anchor Column A location on the Scan-See display – the anchor – is chosen as a reference point.
Chapter 6: Tekterm Application Scan-See Sub-Menu – Mapping The Viewport 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 . . . 0 1 (0,0) terminal cursor 2 3 4 (7,5) +4 5 offs 6 anchor (0,0) (4 +2 (11, 7) 8 ,2) et +2 9 0 1 2 3 4 5 6 7 8 9 0 et 7 +4 offs (9,0) 10 pivot = Scan-See Display terminal cursor + offset ... 11 1 Terminal Display superimposing the anchor on the pivot 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 . . .
Chapter 6: Tekterm Application Scan-See Sub-Menu – Mapping The Viewport Follow Cursor When the “Follow Cursor” parameter is disabled (set to “N”), the cursor is always assumed to be located at the origin. Using the previous example: • the area displayed will be (4–9,2–0) to (4–9+9, 2–0+1), or, after clipping values that are negative or higher than 80: (0,2) to (4,3).
Chapter 6: Tekterm Application Scan-See Sub-Menu – Mapping The Viewport Arrows The “Arrows” parameter assigns one of three possible functions to the two arrow keys on the Scan-See keyboard: Value Function “Bright” Arrow keys control Scan-See display brightness “Horiz” Arrow keys control “Column Offset” “Vert” Arrow keys control “Line Offset” Table 6.6 “Arrow” Parameter Options Note: For “Horiz” and “Vert,” changing the offset will take affect only after the 7535 display has been updated.
Chapter 6: Tekterm Application Scan-See Keyboard Mapping When this parameter is set to “Y”, the XON and XOFF characters are not passed to the TESS or ANSI tasks. A received XOFF character stops the serial port from transmitting. A received XON character starts the serial port transmissions again. 6.19.3.2 Scan-See Keyboard Mapping • Digits (0-9) are passed verbatim • The CLR key forces a sign-on message and display refresh.
Chapter 6: Tekterm Application Network Ctrl Panel Settings 6.20.1 Network Ctrl Panel Settings This option displays a Windows CE screen where you can set up your radio, launch an existing network connection or create a new connection. The radio icon (NETWLAN1in the sample screen) in this window is used to configure the radio installed in the 7535 Figure 6.11 Network Settings Important: Follow the steps outlined in “Configuring An IEEE 802.
Chapter 6: Tekterm Application 802.IQ v2 Port “Port” specifies the UDP port used by 802IQ v2. The default value is 8888. Keep in mind that the value assigned here must match the value set at the network controller. Note: When using 802.IQ v2, make certain that the 7535 “Net Mask” matches the network controller net mask. More Parameters Important: The 802.IQ radio items listed in this menu are only available to Psion Teklogix personnel. 05 802.
Chapter 6: Tekterm Application 802.IQ v2 Initial RTT (Round Trip Time) Round trip time is the elapsed time between a 7535 hand-held computer transmission and an access point acknowledgement. Each 7535 continuously adjusts the acceptable round trip time, calculating the average elapsed time over a number of transmissions. If an acknowledgement takes longer to receive than the average round trip time calculated, the 7535 will resend the transmission.
PERIPHERAL DEVICES & ACCESSORIES 7 7.1 External Bar Code Readers. . . . . . . . . . . . . . . . . . . . . . . . . . 251 7.1.1 PowerScan™ Standard, LR and XLR Bar Code Scanners . . . . . . 251 7.1.2 Entering Data With The Bar Code Reader. . . . . . . . . . . . . . . 251 7.2 The 7535 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 7.2.1 Lithium-Ion Battery Safety Precautions . . . . . . . . . . . . . . . . 252 7.3 Important Charger Safety Instructions . . . . . . . . . . . . . . .
Chapter 7: Peripheral Devices & Accessories 7.7.4 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 7.8 Quad Dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 7.8.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 7.8.2 Indicators And Controls . . . . . . . . . . . . . . . . . . . . . . . .263 7.8.3 Using The Quad Dock . . . . . . . . . . . . . . . . . . . . . . . . .263 7.8.4 Network Access. . . . . . . . . . . . . . . . . .
Chapter 7: Peripheral Devices & Accessories External Bar Code Readers 7.1 External Bar Code Readers 7.1.1 PowerScan™ Standard, LR and XLR Bar Code Scanners Note: Refer to “SE1200 High Performance & Long Range Specs” on page 281 for detailed specifications. The 7535 supports Psion Teklogix’ PowerScan™ industrial bar code scanner with standard, long range and extra long range options. To connect this scanner to the 7535, attach the device to the tether port at the upperright side of the 7535.
Chapter 7: Peripheral Devices & Accessories Lithium-Ion Battery Safety Precautions 7.2.1 Lithium-Ion Battery Safety Precautions Important: It is critical that this safety information be reviewed and that all warnings be strictly followed. Warning: BATTERIES ARE CONSIDERED HAZARDOUS WASTE and must be returned to Psion Teklogix for proper disposal. All used batteries must be forwarded to one of the following offices: Psion Teklogix Inc. Psion Teklogix Corp. 2100 Meadowvale Blvd.
Chapter 7: Peripheral Devices & Accessories Important Charger Safety Instructions • • • • • • Do not continue charging the battery if it does not recharge within the specified charge time. The battery may burst or ignite if the battery leaks. Always ensure that it is away from any exposed flames. If leaking electrolyte sprays into your eyes, rinse them with clean running water, and immediately seek medical attention. Do not store the battery in extremely high temperatures (e.g.
Chapter 7: Peripheral Devices & Accessories Chargers • • • • • The extension cord is properly wired and in good electrical condition and that the wire size is larger than 16 AWG. Do not expose the charger to rain or snow. Do not place batteries in the charger if they are cold from extended exposure to a freezer or outside temperatures below 10°C (50°F). Allow them to warm up to room temperature for at least two hours.
Chapter 7: Peripheral Devices & Accessories Installation 7.5.1 Installation The gang charger can be wall mounted using the wall mount kit – PN 1010039 – or it can be operated on a flat surface. Install the charger in an area that is free from excessive dirt, dust and contaminants. The ambient temperature must be in the range 0˚ C to 39˚ C (32˚ F to 102˚ F). The charger will not charge batteries outside of this temperature range.
Chapter 7: Peripheral Devices & Accessories Charge Indicators 7.5.3 Charge Indicators Each battery charge slot is equipped with a tri-coloured LED to indicate the charge status of the battery. When 7535 batteries are inserted in the charger, the colour and behaviour of the LEDs associated with the charge wells in use indicate the status of the charge. LED Behaviour Off Solid green Flashing green Solid yellow Flashing yellow Solid red Flashing red Icon Charge Status No battery detected in the slot.
Chapter 7: Peripheral Devices & Accessories Troubleshooting 7.5.5 Troubleshooting 7.5.5.1 Excessive Charge Duration The charger is equipped with a recalibration function – a function that fully discharges and then fully recharges the battery. This process is necessary to recalibrate the battery capacity gauge internal to the battery.
Chapter 7: Peripheral Devices & Accessories Indicator Does Not Light When Battery Installed 7.5.5.4 • • • • • Indicator Does Not Light When Battery Installed Remove the battery, and clean the contacts on the battery and the charge slot. Reinstall the battery, and check that it is fully seated in the slot. Inspect the charge slot contacts for damage (are they bent, flattened, twisted or broken). Try inserting a battery that you know to be working in the charger slot.
Chapter 7: Peripheral Devices & Accessories Operator Controls 7.6.2 Operator Controls The combo charger has no operator controls or power switch. 7.6.3 Using the Combo Charger With The 7535 • Gently slide the 7535 into the cradle portion of the combo charger until lightly latched. An icon is displayed indicating that the 7535 is properly installed in the combo charger – . The battery charge LED on the 7535 lights up indicating that the unit has external power and battery charging may begin.
Chapter 7: Peripheral Devices & Accessories Charge Indicators 7.6.5 Charge Indicators The spare battery charge slot has an associated tri-colour LED indicator on the lower-right area of the front panel. LED Behaviour Off Solid green Flashing green Solid yellow Flashing yellow Solid red Flashing red Charge Status No battery detected in the slot. Battery is fully charged. Battery is charged to 75% capacity. Charge in progress.
Chapter 7: Peripheral Devices & Accessories Bluetooth Peripherals 7.10 Bluetooth Peripherals If the 7535 is equipped with a Bluetooth radio, it is possible to communicate with a variety of Bluetooth peripherals, including GSM/GPRS handsets, scanners, printers, and so on. The range of the Bluetooth radio in the 7535 is limited to approximately 2 meters. Psion Teklogix provides built-in support for the Bluetooth peripherals listed below.
Chapter 7: Peripheral Devices & Accessories Picker Cradle Mounting Recommendations 7.11.1 Picker Cradle Mounting Recommendations Warning: Before mounting a picker cradle in a vehicle, there are a number of operator safety issues that require careful attention. An improperly mounted cradle may result in one or more of the following: operator injury, operator visibility obstruction, operator distraction and/or poor ease of egress for the operator.
Chapter 7: Peripheral Devices & Accessories Wiring Guidelines 7.11.2 Wiring Guidelines Before installing the cables between the cradle and other devices, consider the following: • • • • • • Ensure that drilling holes will not damage the vehicle or its wiring. Protect cable runs from pinching, overheating and physical damage. Use grommets to protect cables that pass through metal.
Chapter 7: Peripheral Devices & Accessories Powered Cradle Installation In High Voltage Vehicles 7.11.5 Powered Cradle Installation In High Voltage Vehicles Warning: Voltages exceeding 60VDC are considered hazardous. For powered cradle installations on vehicles with batteries above this voltage, ensure the powered cradle power connector is mounted in a dry location on the vehicle, or that the connector is insulated with an appropriate waterproof material after installation.
Chapter 7: Peripheral Devices & Accessories Powered Cradle Installation 7.11.6 Powered Cradle Installation The powered cradle option is designed to allow the 7535 to be powered by a vehicle battery. The battery installed in the 7535 is also recharged by the vehicle battery. This option accepts DC power sources over the range 12V to 80V. The 7535 picker cradle can be ordered with the powered cradle option installed, or it can be retrofitted later at an authorized Psion Teklogix service depot.
Chapter 7: Peripheral Devices & Accessories Wiring Vehicle Power To The Cradle 7.11.6.1 Wiring Vehicle Power To The Cradle A 1.8 meter (6 foot) extension power cable (PN 13985) is supplied with your power cradle. This cable should be wired to a filtered, fused (maximum 10A) accessory supply on the vehicle. The power cradle draws no more than 8A (less if the accessory supply is greater than 12V). Any additional wiring, connectors or disconnects used should be rated for at least 10A.
Chapter 7: Peripheral Devices & Accessories The Port Replicator 7.11.7 The Port Replicator The port replicator is an optional accessory that allows tethered devices (e.g., scanners) as well as mounted peripherals (e.g., bar code printers or weigh scales) to be attached to the picker cradle. The replicator can be used with or without the cradle power option. The functionality of the 7535 tether port is duplicated on the port replicator.
8 SPECIFICATIONS 8.1 7535 Hand-Held Computer Specifications . . . . . . . . . . . 8.2 Radio Specifications . . . . . . . . . . . . . . . . . . . . . . 8.3 Bar Code Scanning . . . . . . . . . . . . . . . . . . . . . . . 8.3.1 Internal Scanners . . . . . . . . . . . . . . . . . . . . . 8.3.2 Internal Scanner Port. . . . . . . . . . . . . . . . . . . 8.3.3 External Scanners . . . . . . . . . . . . . . . . . . . . 8.4 Internal Scanner Specifications. . . . . . . . . . . . . . . . . 8.4.
Chapter 8: Specifications 7535 Hand-Held Computer Specifications Note: Performance specifications are nominal and subject to change without notice. 8.1 7535 Hand-Held Computer Specifications Size • • 4" (102mm) width x 2.5" (62.5mm) depth x 9.6" (244mm) length Keypad area: 3" (75.5mm) width x 1.4" (36mm) depth Weight With battery 21.7 oz (700g) With pistol grip add 4.3 oz (125g) Operating System Microsoft® Windows® CE.net Version 4.
Chapter 8: Specifications 7535 Hand-Held Computer Specifications Communication Ports Tether port (optional) with: - one RS232 serial port (decoded scanner, printer) undecoded scanner port USB host port, power out - Docking station port with: one RS232 serial port including diagnostics USB device port, USB host port, power in/out Environmental Guaranteed Operating Temperature Range Storage Temperature Rain And Dust Resistance Humidity Drop Durability 32°F to 122°F (0°C to +50°C) Short exposure to temperat
Chapter 8: Specifications Radio Specifications 8.2 Radio Specifications 802.11b Direct Sequence Spread Spectrum 802.11b/g Model: RA2040 Transmit Power 15 dBm for 'b' 13 dBm for 'g' Frequency Range 2.400-2.474 for USA, Canada 2.400-2.484GHz for EU Channels 1 to 11 for USA, Canada 1-13 for EU countries Data Rates 1,2,5.5, and 11 Mbps for 'b' 6,9,12,18,24,36,48, and 54 Mbps for 'g' 8.3 Bar Code Scanning Scanner Types Decoded and non-decoded.
Chapter 8: Specifications Internal Scanner Port Scan Triggering If an aiming dot is available on the installed scanner, the aiming dot will be enabled for a configurable time period after which normal scanning begins. Double-clicking trigger will override aiming delay and initiate immediate scan. 8.3.
Chapter 8: Specifications Internal Scanner Specifications 8.4 Internal Scanner Specifications 8.4.1 SE1200 High Performance & Long Range Specs Parameter 7535 High Performance (SE 1200HP) Visible Laser Diode, 675nm ± 5nm CDRH Class II Laser Class DIN EN 60825: July 1993, Class 2 1.0 mW Max.
Chapter 8: Specifications SE1200 Advanced Long Range & SE2223 PDF Specs 8.4.2 SE1200 Advanced Long Range & SE2223 PDF Specs Parameter Light Source Scan Rate Scan Angle Horizontal: Vertical Scan Patterns Minimum Print Contrast Symbologies Programmable Parameters Ambient Light: Artificial: Sunlight: 7535 Advanced Long Range (SE 1200ALR) Visible Laser Diode 650 nm Visible Laser Diode 650 nm 35 (± 5) scans/sec (bi-directional) 590 scans/sec. 22 frames/sec. 13º ± 2º Linear 34º 12.
Chapter 8: Specifications SE1200 Advanced Long Range & SE2223 PDF Specs Pitch Pitch Angle Scanner Side View Scan Beam Barcode Surface Skew Skew Angle Scanner Barcode Surface Top View Scan Pattern Specular Dead Zone < 2º Scanner Side View Scan Beam Barcode Surface Roll Scanner Side View Scan Beam Barcode Surface Figure 8.
Chapter 8: Specifications Decode Zones 8.4.3 Decode Zones Bar Code Read Distance High Performance Min Max 5 mil 7.5 mil 10 mil 15 mil 20 mil 40 mil 55 mil 3.0" 3.0" 2.5" 2.5" 2.5" 3.0" 3.5" 4.5" 8.5" 12.5" 18.5" 20.5" 29.5" 35.5" Advanced Long Range Min Max Long Range Min Max 13.0" 8.5" 9.5" 9.5" 9.5" 17.5" 33.5" 38.5" 79.5" 89.5" 20.0" 30.0" 30.0" 27.0" 50.0" 60.0" 98.0" 115.0" Table 8.3 Decode Zones – HP, LR And ALR Bar Code Raster Laser Scanner Read Distance PDF Bar Codes S2223 Min 6.
Chapter 8: Specifications PowerScan™ LR and XLR Industrial Scanner Specs Electrical Operating voltage Operating current - nominal 4 VDC to 14 VDC Undecoded: 75 mA @ 5 VDC Decoded: 100 mA @ 5 VDC Idling current - low power mode < 50 µA @ 5 VDC Optical Light source Scan System Rate Depth of field - Long Range Extra bright 650 nm Visible Laser Diode (VLD) Frictionless lifetime flexure mechanism 35 scans/sec nominal Paper Labels (decoded) 7.
Chapter 8: Specifications PowerScan™ LR and XLR Industrial Scanner Specs Print Contrast Ratio Pitch Skew Ambient Light Immunity 25% minimum ± 65˚ ± 55˚ Artificial light: 1200 ft. candles. Sunlight: 8000 ft. candles. Environmental Temperature Rating Humidity Shock (at 23˚ C) Vibration Water and Dust Operating: -22˚ to 122˚ F (-30˚ to 50˚ C) Storage: -40˚ to 158˚ F (-40˚ to 70˚ C) 5 to 95% NC Withstands multiple 6 foot drops to concrete.
Chapter 8: Specifications PowerScan™ Standard Range Scanner Specs 8.5.2 PowerScan™ Standard Range Scanner Specs Communication Undecoded Standard and Intermec-compatible. Mechanical Dimensions Weight 6.9 x 11.2 x 18.3 cm (2.7 x 4.4 x 7.2 in) Scanner - 280 g (9.9 ozs) Cable (82.3 cm 32 in) - 176 g (6.
Chapter 8: Specifications Lithium-Ion Battery Pack Electrical Operating voltage Operating current - nominal 4 VDC to 14 VDC Undecoded: 75 mA @ 5 VDC Decoded: 100 mA @ 5 VDC Idling current - low power mode < 50 µA @ 5 VDC Environmental Temperature Rating Humidity Shock (at 23˚ C) Vibration Water and Dust Operating: -22˚ to 122˚ F (-30˚ to 50˚ C) Storage: -40˚ to 158˚ F (-40˚ to 70˚ C) 5 to 95% NC Withstands multiple 6 foot drops to concrete.
Chapter 8: Specifications Lithium-Ion Battery Pack radation below 70% of nominal capacity Charge Time Charge time is typically 1.5 hours. Voltage 7.4 V nominal (6V min. to 8.4V max.) Cell Configuration 2 series connected cells Capacity 1800 mAh nominal at 300mA discharge 20˚C to 6.
APPENDIX A SUPPORT SERVICES AND WORLDWIDE OFFICES A.1 Support Services Psion Teklogix provides a complete range of product support services to its customers worldwide. These services include post-installation technical support and product repairs. A.1.1 Canada and USA: Technical Support and Repair Services In Canada and the U.S.A. these services can be accessed through the Psion Teklogix Helpdesk.
A.2 WORLDWIDE OFFICES COMPANY HEADQUARTERS AND CANADIAN SERVICE CENTRE NORTH AMERICAN HEADQUARTERS AND U.S. SERVICE CENTRE Psion Teklogix Inc. 2100 Meadowvale Boulevard Mississauga Ontario Canada L5N 7J9 Tel: +1 905 813 9900 Fax: +1 905 812 6300 Email: salescdn@psion.com Psion Teklogix Corp. 1810 Airport Exchange Boulevard Suite 500 Erlanger, Kentucky USA 41018 Tel: +1 859 371 6006 Fax: +1 859 371 6422 Email: salesusa@psion.
Psion Teklogix de Argentina, S.A. Avenida Moreau de Justo 1180 Piso 1, Oficina C-105 Buenos Aires 1107 Argentina Tel: +54 11 4343 0193 Fax: +54 11 4343 6310 Email: tekar@psion.com Psion Teklogix Africa Postnet Suite 39, Private Bag x11 Halfwayhouse, 1685 Ground Floor East Waterfall Edge Phase 2, Waterfall Park Bekker Road MIDRAND 1685 South Africa Tel: 27-11-805-7440/1/2 Fax: 27-11-805-7444 Psion Teklogix España, S.L. Cityparc Ronda de Dalt Ctra.
APPENDIX B PORT PINOUTS B.1 7535 Tether Port Pinout The tether port connector incorporates multiplexed undecoded scanner, decoded scanner, RS232 serial, and USB interfaces. In order for it to operate, a special wiring scheme is needed. If you have a need to create cables for the tether port, contact Psion Teklogix and request document # 1010008 “Instruction Tether Port Termination”.
Appendix B: Port Pinouts Battery Contacts 9. 10. 11. 12. Ground. USB Device Minus. When terminal operated as a USB device. USB Device Plus. When terminal operated as a USB device. Ground B.3 Battery Contacts These contacts represent right to left numbering with the 7535 docking port pointing toward you. 1. Battery Plus 2. SMBUS CLK 3. Battery ID. Identifies battery type (2 cell-100K resistor to Battery Negative, 3-cell 100K resistor to battery Negative). 4. SMBUS Data. 5. Battery Negative.
APPENDIX C USB SETUP APPLICATION C.1 USB Setup The USB Setup application (PN 1000997) is used to update a Windows PC so that it can connect to a Psion Teklogix 7535. System Requirements • • Windows® 2000 or XP ActiveSync 3.1 or later The two driver classes that control USB communication are usbstor (for communication with a device running BooSt) and wceusbsh (for communication through ActiveSync with a device running Windows CE).
Appendix C: USB Setup Application Pre-Installation: Updating usbstor.inf And wceusbsh.inf C.1.2 Pre-Installation: Updating usbstor.inf And wceusbsh.inf 1. Welcome Dialogue Box: You can click on the and buttons to navigate between the pre-install windows. At any time during the pre-installation process, you can tap on to exit the program. • • Shut down all other software programs – especially ActiveSync – to avoid a restart request during installation. Tap on the button.
Appendix C: USB Setup Application Pre-Installation: Updating usbstor.inf And wceusbsh.inf • If necessary, tap on the buttons to select different paths for the inf files. 3. Device Driver Install Selection Dialogue Box: You can choose to have the device drivers installed immediately by selecting the check box (√), or you can leave the check box blank and Windows will install the 7535 the next time it is connected. It is recommended that the device be installed immediately.
Appendix C: USB Setup Application Installation: Installing The 7535 As a Device On Your PC C.1.3 Installation: Installing The 7535 As a Device On Your PC 1. Install Dialogue Box: The .sys files you selected are copied to the backup directory. If an unknown error occurs during the backup, you are asked whether you’d prefer to cancel the install or continue with the process. The wceusbsh.inf and usbstor.inf files are updated. 2.
Appendix C: USB Setup Application Post Installation completed the driver installation and the device is no longer marked for reinstall. Only one devnode per device can be ‘unset’ when the device drivers are finally installed. 3. If you indicated that the usbstor driver should be installed, the same steps as described above are carried out for usbstor except that the 7535 must be running BooSt. (Press and hold down the keys for a minimum of 6 seconds to launch the BooSt program.
INDEX Boldface indicates a parameter name.
Index Boldface indicates a parameter name. Password Prompt (Telnet Settings) 198 Port 197 sessions, closing 165 sessions, establishing new 165 sessions, listing 165 sessions, moving between 165 settings 195–211 Telnet connection 196 Terminal # 195 transmitting data 124, 126, 204 Xmit Modes 202–205 802.IQ connection 196 ANSI Settings Connection Type - Telnet & TCP Direct 196 Screen settings 199 AP/Controller mac , displaying 167 App.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name.
Index Boldface indicates a parameter name. Settings 73 Shutdown 75 system tray 70 task manager 71 start up menu 168 statistics screen 802.
Boldface indicates a parameter name. Ign Bcode_fld 226 Insert mode 156 Kbd Locked 220 keyboard lock 220 matching fields via data stream 217 milestone 220 modes (edit) 156 multiple sessions 194 number of columns in screen 214 number of rows in screen 214 Pages Saved 215 Port 213 query command 215 Replace mode 156 resetting a TESS session 160 Reverse (video attrib.
Index Boldface indicates a parameter name.
Boldface indicates a parameter name. Index 7535 picker cradle See also Picker Cradle 268 80-col. font 200 802.IQ connection (ANSI) 196 802.IQ connection (TESS) 213 802.IQ v1(protocol) Auto Radio Addr 179 802.IQ v2 245 802.1X authentication, enabling 23 802.
