Chapter 5: Configuration Imager Setting this parameter to on allows the imager to make automatic gain, integration and illumination adjustments based on ambient light before capturing the bar code. If the adjustment is insufficient, further adjustments are made automatically before another image is captured. Fast Converge Note: “Auto Exposure” must be set to ‘on’ in order for this parameter to function.
Chapter 5: Configuration Imager first. Adaptive Windowing “Adaptive Windowing” is an advanced technique used to speed up bar code recognition in certain applications. This parameter automatically reduces the size of the window to the user-programmed window size when it successfully decodes (which reduces decode time the next time it is used), but increases it to the full size window (1280x1024 for SX5303) on a failed decode.
Chapter 5: Configuration Imager 5.11.5.5 EAN 13 Enabled Set this parameter to on to enable “EAN 13”. Addendum An addendum is a separate bar code, supplementary to the main bar code. This parameter provides three options: Disabled, Optional and Required. Depending on the value chosen for this parameter, an addendum is recognized or ignored. • Double-tap on Addendum to display a dialog box listing your options. • Highlight an item, and tap on OK.
Chapter 5: Configuration Imager 5.11.5.7 UPC A Enabled Set this parameter to on to enable “UPC A”. Addendum Refer to “Addendum” on page 195. Prefix/Suffix Refer to “Prefix/Suffix” beginning on page 144. 5.11.5.8 UPC E Enabled Set this parameter to on to enable “UPC E”. Addendum Refer to “Addendum” on page 195. Prefix/Suffix Refer to “Prefix/Suffix” beginning on page 144. 5.11.5.9 Code 93 Enabled Set this parameter to on to enable “Code 93”. Field Size/Char Refer to page 143 for details. 5.11.5.
Chapter 5: Configuration Imager 5.11.5.11 Interleaved 2 of 5 Enabled Set this parameter to on to enable “Interleaved 2 of 5”. Field Size/Char Refer to page 143 for details. 5.11.5.12 RSS Code (Reduced Space Symbology) Enable Setting this parameter to on enables “RSS Code” scanning capability. Field Size/Char Refer to page 143 for details. 5.11.5.13 Composite Important: To successfully read this type of bar code, the two types of symbologies included in a composite bar code must be enabled.
Chapter 5: Configuration Imager 5.11.5.15 Micro PDF-417 Enable Setting this parameter to on enables “Micro PDF-417” bar code scanning. Micro PDF-417 is a multi-row symbology that is useful for applications requiring greater area efficiency but lower data capacity than PDF-417. Field Size/Char Refer to page 143 for details. 5.11.5.16 2D Data Matrix Enable Set this parameter to on to enable “Data Matrix”. Field Size/Char Refer to page 143 for details. 5.11.5.
Chapter 5: Configuration Imager Field Size/Char Refer to page 143 for details. 5.11.5.20 Postal: PlaNET Enabled Set this parameter to on to enable “Postal: PlaNET”. Field Size/Char Refer to page 143 for details. 5.11.5.21 Postal: PostNET Enabled Set this parameter to on to enable “Postal: PostNET”. Field Size/Char Refer to page 143 for details. 5.11.5.22 Postal: Australian Enabled Set this parameter to on to enable “Postal: Australian”. Field Size/Char Refer to page 143 for details. 5.11.5.
Chapter 5: Configuration Options 5.11.5.24 Postal: Korean Enabled Set this parameter to on to enable “Postal: Korean”. Field Size/Char Refer to page 143 for details. 5.11.5.25 Postal: Royal Enabled Set this parameter to on to enable “Postal: Royal”. Field Size/Char Refer to page 143 for details. 5.11.6 Options This tab allows you to tailor the double-click parameters and the display options associated with your scanner. 200 WORKABOUT PRO G2 Hand-Held With Windows Embedded CE 5.
Chapter 5: Configuration Options 5.11.6.1 Double Click Parameters Click Time (msec) This parameter controls the maximum gap time (in milliseconds) for a double-click. If the time between the first and second clicks of the scanner trigger is within this time, it is considered a double-click. The allowable range is 0 to 1000. A value of zero disables this feature. A double-click produces different results depending on whether or not a value is assigned in the “Click Data” parameter.
Chapter 5: Configuration Options Note: To remove the scan result from the screen before the “Result Time” has expired, point the scanner away from the bar code and press the trigger. Good Scan Beep And Bad Scan Beep These parameters determine whether or not the hand-held emits an audible scanner ‘beep’ when a good (successful) scan or a bad (unsuccessful) scan is performed. Set these parameters to either on to enable the beeper or off to disable it.
Chapter 5: Configuration Translations Tab 5.11.7 Translations Tab The Translations tab allows you to define up to 10 cases, each consisting of up to 10 rules in sequential order. Only one case will be applied to a bar code and a case will only be applied if all rules specified in the case are successful – if a rule within a case fails, the entire case fails. • In the Translation tab, tap on the Case # to create rules. WORKABOUT PRO G2 Hand-Held With Windows Embedded CE 5.
Chapter 5: Configuration Translations Tab • Tap on the No rule dropdown menu to display the rules. When you choose a rule, an associated screen is displayed in which you can define the rule. 204 WORKABOUT PRO G2 Hand-Held With Windows Embedded CE 5.
Chapter 5: Configuration SNMP (Simple Network Management Protocol) Setup 5.11.7.1 Case Rules The case rules are defined as follows: • No rule – ignored. • Search and replace – replaces all instances of the match string. (Note that this rule cannot fail.) • Match at index – matches the match string at a specified index. • Match and replace at index – matches the match string at a specified index and replaces/changes it. • Replace at index – replaces/changes unspecified data in a given range.
Chapter 5: Configuration Contact Tab All devices also support MIB-II, a management information base that defines the common features of TCP/IP networks. The SNMP Agent software embedded in the WORKABOUT PRO G2 product supports SNMPv1 (RFC 1157). • In the Control Panel, choose the SNMP icon. Figure 5.20 SNMP Icon 5.12.1 Contact Tab The SNMP dialog box is displayed. Contact This field identifies the contact person for this managed node along with information about how to get in touch with this person.
Chapter 5: Configuration Communities Tab Location This parameter is used to identify the physical location of this node (e.g., Warehouse A: Pillar 32B). The content of this parameter is accessible through MIB-II’s sysLocation object. 5.12.2 Communities Tab The Communities tab allows you to limit access to SNMP-managed devices to those SNMP Managers with matching “community names”, as specified by RFC 1157. Enable SNMP Enabling Enable SNMP allows the device to respond to SNMP queries and to send Traps.
Chapter 5: Configuration Communities Tab Name The value assigned here is the name assigned by the network administrator to the set of devices to which this managed node belongs. Rights This menu allows you to specify access, that is, ‘Read-Only’ or ‘Read-Write’ 5.12.2.2 Modifying A Community Setting To modify an existing community: • Highlight the community you want to alter. • Choose the Change button. A Modify Community dialog box is displayed, listing the community you highlighted.
Chapter 5: Configuration Trap Destination Tab 5.12.3 Trap Destination Tab A trap is an unsolicited report sent to SNMP Managers by the SNMP Agent running on the managed node. This option allows you to define where the report will be sent. 5.12.3.1 Enabling Authentication TRAPS Enabling Enable Authentication TRAPS allows authorization traps to be sent when a failure is detected (e.g., an SNMP message received with a bad community name). 5.12.3.
Chapter 5: Configuration Permitted Hosts Tab A dialog box like the one displayed when you add a destination is displayed. • Make the changes to the destination, and press [ENTER] to save the changes. 5.12.3.4 Removing A Trap Destination To remove a trap destination: • In the Trap Destination tab, highlight the destination you want to delete. • Choose the Remove button. A Delete Confirmation screen is displayed.
Chapter 5: Configuration Permitted Hosts Tab 5.12.4.1 Adding A Host To add a new host: • Highlight the Add button, and press [ENTER]. • Type a new host IP address in the text box provided, and press [ENTER]. 5.12.4.2 Changing A Host To change an existing host IP address: • Highlight the IP address you want to alter in the Permitted Hosts tab, and then choose the Change button. A dialog box like the one displayed when you add a host is displayed. • Make the necessary changes, and press [ENTER].
PERIPHERAL DEVICES & ACCESSORIES 6 6.1 Carrying Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 6.1.1 Attaching The Hand Strap . . . . . . . . . . . . . . . . . . . . . . . 215 6.1.2 Attaching The Pistol Grip . . . . . . . . . . . . . . . . . . . . . . . 217 6.1.3 Protective Carrying Case. . . . . . . . . . . . . . . . . . . . . . . . 218 6.1.3.1 Using The Swivel Belt Loop With The Carrying Case . . . . . 218 6.1.4 Soft Shell Holster . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6: Peripheral Devices & Accessories 6.6 Quad Battery Charger–Model #WA3004-G1 . . . . . . . . . . . . . . . . . 229 6.6.1 Charging Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 6.6.2 Battery Charge Duration . . . . . . . . . . . . . . . . . . . . . . . . 230 6.6.3 Charge Indicators–The LEDs. . . . . . . . . . . . . . . . . . . . . . 230 6.6.4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 6.6.4.1 Excessive Charge Duration . . . . . . . . . . . . .
Chapter 6: Peripheral Devices & Accessories Carrying Accessories 6.1 Carrying Accessories There are a variety of carrying accessories to help the operator work safely and comfortably with the WORKABOUT PRO G2. Carrying Accessory Model Number Hand Strap WA6025 for WORKABOUT PRO C G2 WA6125 for WORKABOUT PRO S G2 Pistol Grip WA6001-G1 Pistol Grip for SX5393 Imager WA6002-G1 Protective Vinyl Case WA6091 for WORKABOUT PRO C G2 WA6190 for WORKABOUT PRO S G2 Soft Shell Holster WA6050 Table 6.
Chapter 6: Peripheral Devices & Accessories Attaching The Hand Strap 216 • Use a Phillips screwdriver to attach the strap to the two threaded inserts on the back of the WORKABOUT PRO G2, near the top of the unit • Stretch the hand strap toward the base of the WORKABOUT PRO G2, and hook the bottom of the strap into the slot near the base of the battery pack. WORKABOUT PRO Hand-Held Computer With Windows Mobile 5.
Chapter 6: Peripheral Devices & Accessories Attaching The Pistol Grip 6.1.2 Attaching The Pistol Grip The pistol grip is attached to the four threaded inserts on the back of the WORKABOUT PRO G2. Four Phillips head screws are provided with this accessory. Note: • Prior to installation, make sure the trigger mechanism is securely snapped into the pistol grip body and that the trigger operates properly.
Chapter 6: Peripheral Devices & Accessories Protective Carrying Case • Tighten the screws to a torque of 3 lbs-in (3kgf-cm) to secure the pistol grip in place. 6.1.3 Protective Carrying Case A carrying case is available for WORKABOUT PRO G2s to shield the unit from damage. It is equipped with a soft plastic window to protect the unit display and keyboard. A variety of cases are available, depending on the type of end-cap attached to your unit. 6.1.3.
Chapter 6: Peripheral Devices & Accessories Protective Carrying Case • Slide your belt through the belt loop. Figure 6.2 Attaching The Belt Loop Alternatively, you can attach a plastic clip to the swivel belt loop and clip it to your waistband or belt. Belt Clip Figure 6.3 Belt Clip WORKABOUT PRO Hand-Held Computer With Windows Mobile 5.
Chapter 6: Peripheral Devices & Accessories Soft Shell Holster 6.1.4 Soft Shell Holster A soft shell holster with removable belt and swivel holster pad can be used to hang a WORKABOUT PRO G2 with a pistol grip from you waist Soft Shell Holster Swivel Holster Pad and Removable Belt Figure 6.4 Soft Shell Holster • • • 220 Insert the belt in the swivel holster pad. Attach the pad on either the left or right side of the holster case, depending on whether you are left- or right-handed.
Chapter 6: Peripheral Devices & Accessories The Batteries 6.2 The Batteries The WORKABOUT PRO G2 will operate with a High-Capacity Lithium Ion battery pack, a Super High-Capacity Lithium Ion battery pack. In addition to the main battery, the hand-held is equipped with a rechargable coin battery–a Maxell ML2032. 6.3 Chargers And Docking Stations Important: Keep in mind when ordering a charger or docking station, you must also order the appropriate power cord separately.
Chapter 6: Peripheral Devices & Accessories Operator Controls • Quad docking station–can consume up to 3A @ 120VAC or 1.5A @ 240VAC. 6.3.3 Operator Controls WORKABOUT PRO G2 docking stations and chargers have no operator controls or power switches. 6.3.4 Important Charger Safety Instructions • • • • • • • • • • • • • 222 SAVE THESE INSTRUCTIONS–This manual contains important safety and operating instructions for battery charger s.
Chapter 6: Peripheral Devices & Accessories Desktop Docking Station • • Do not use the charger if, after an overnight charge, any of the batteries feel warmer than the charger housing. The charger should be inspected by qualified service personnel. Do not use the charger if any of the batteries or the charger get more than lukewarm. The equipment should be inspected by qualified personnel. 6.
Chapter 6: Peripheral Devices & Accessories Charging A Battery Installed In The WORKABOUT PRO G2 The desktop docking station is designed to charge the battery installed in the WORKABOUT PRO G2 along with a spare battery pack. Spare Battery Spare Battery Charge Well DC IN Socket Figure 6.6 Back Of Desktop Docking Station Important: This docking station can only be used to charge Psion Teklogix approved Lithium-Ion batteries–specifically model numbers WA3000-G1 and WA3006. 6.4.
Chapter 6: Peripheral Devices & Accessories Charging A Spare Battery 6.4.2 Charging A Spare Battery • Insert the battery in the spare battery charge well at the back of the docking station, aligning the contacts on the battery with the contacts in the spare battery charge well. 6.4.3 Battery Charge Duration A fully discharged battery can take up to 5 hours to charge.
Chapter 6: Peripheral Devices & Accessories Desktop Docking Station Ports 6.4.6 Desktop Docking Station Ports DC IN Socket Client USB Port Host USB Port Figure 6.7 Back of Desktop Docking Station The desktop docking station is equipped with two USB ports–a Host USB port to connect peripherals such as a printer, keyboard, etc. and a Client USB to connect the docking station to a PC. 6.4.
Chapter 6: Peripheral Devices & Accessories Linking A WORKABOUT PRO G2 To An Ethernet Network To link the WORKABOUT PRO G2 to a PC: • Insert the hand-held in the desktop docking station. • Insert the USB cable into the docking station Client USB connector. Attach the other end of the cable to a USB port on the PC. You’ll need to install connectivity software on your PC before you can pass information between the hand-held and the PC. 6.4.7.
Chapter 6: Peripheral Devices & Accessories Troubleshooting The Docking Station Operations If a link is established between a WORKABOUT PRO G2 and a host, the application on the host and on the hand-held must have a recovery mechanism in the event that the WORKABOUT PRO G2 is removed from the dock, interrupting the link. 6.4.
Chapter 6: Peripheral Devices & Accessories Charge Indicators–The LED 6.5.3 Charge Indicators–The LED The LED on the top of the charger indicates battery charge progress. LED Behaviour Charge Status Off Solid green Fast flashing green Slow flashing green No battery detected in the charge well. Battery is fully charged. Battery is charged to 75% of capacity. Charge in progress. Battery is outside ambient temperature range of 0° C to 45 °C (32° F to 113° F).
Chapter 6: Peripheral Devices & Accessories Charging Batteries 6.6.1 Charging Batteries • Slide the battery into a charge well, aligning the contacts on the battery with the contacts in the charge well. 6.6.2 Battery Charge Duration A fully discharged battery can take up to 4 hours to charge. The quad battery charger stops applying power to the battery when it is fully charged–there is no risk of overcharge if the battery remains in the charge well.
Chapter 6: Peripheral Devices & Accessories Troubleshooting 6.6.4.3 • • • • Power LED Does Not Light Up Remove all batteries, and unplug the charger. Connect another device to the mains outlet to ensure there is power. Remove the IEC mains power cable from the charger, and check it for damage. Reconnect the mains cable in the charger and mains outlet. If the power LED still does not light up: • Unplug the mains cable, and check the fuse at the rear of the charger.
Chapter 6: Peripheral Devices & Accessories Quad Docking Station–Model #WA4004-G1 6.7 Quad Docking Station–Model #WA4004-G1 Figure 6.9 Quad Docking Station Note: The quad docking station is shipped with a docking manual. It is critical that this manual be reviewed for additional information and updates. The quad docking station permits each of four docked WORKABOUT PRO G2s to communicate with a 10/100 BaseT Ethernet network at greater than 2Mbps.
Chapter 6: Peripheral Devices & Accessories Quad Indicators A user application must be loaded onto each WORKABOUT PRO G2 that utilizes the quad dock for communication. When the network is connected and this application is loaded, the quad dock is ready for use. 6.7.2 Quad Indicators The quad dock is equipped with a power indicator LED and RJ45 link and traffic indicator LEDs. When a valid network link is established, a green LED is illuminated next to the RJ45 connector. 6.7.
Chapter 6: Peripheral Devices & Accessories Battery Charging–LED Behaviour 6.7.5 Battery Charging–LED Behaviour The quad docking station supplies DC power to enable the WORKABOUT PRO G2 internal fast charger. Charge status is displayed on the hand-held LED–the LED turns red while the battery is being charged and turns green once the charge is complete. If the battery is fully charged when the unit is inserted in the docking station, the LED flashes red for less than a second and then turns green.
Chapter 6: Peripheral Devices & Accessories The Vehicle Cradle 6.8 The Vehicle Cradle The vehicle cradle is a highly ruggedized, single station dock. Although it provides quick insertion and removal, the cradle holds the WORKABOUT PRO G2 securely even when operated in high vibration environments.
Chapter 6: Peripheral Devices & Accessories Wiring Guidelines 6.8.1.1 Mounting Template The vehicle cradle is shipped with detailed mounting instructions including a drill template. 6.8.2 Wiring Guidelines Before installing cables between the cradle and other devices, review the following: • Ensure that drilling holes will not damage the vehicle or its wiring. • Protect cable runs from pinching, overheating and physical damage. • Use grommets to protect cables that pass through metal.
Chapter 6: Peripheral Devices & Accessories Powered Cradle Installation In High Voltage Vehicles 6.8.5 Powered Cradle Installation In High Voltage Vehicles Warning: Voltages exceeding 60VDC are considered hazardous. For powered cradle installations on vehicles with batteries above this voltage, ensure the powered cradle power connector is mounted in a dry location on the vehicle, or that the connector is insulated with an appropriate waterproof material after installation.
Chapter 6: Peripheral Devices & Accessories The Port Replicator 6.8.6.1 Wiring Vehicle Power To The Cradle A 1.8 meter (6 foot) extension power cable (PN 13985) is supplied with your powered vehicle cradle. This cable should be wired to a filtered, fused (maximum 10A) accessory supply on the vehicle. The power cradle draws no more than 8A (less if the accessory supply is greater than 12V). Any additional wiring, connectors or disconnects used should be rated for at least 10A.
Chapter 6: Peripheral Devices & Accessories Bluetooth Peripherals The functionality of the WORKABOUT PRO G2 tether port is replicated into RS232 serial interfaces by the port replicator. It provides the user with 3 DB9 serial interfaces as well as one Type B USB port (for connecting a Host device). 6.
SPECIFICATIONS 7.1 WORKABOUT PRO G2. . . . . . . . . . . . . . . . . . . . 7.2 Radio Specifications . . . . . . . . . . . . . . . . . . . . . . 7.3 Scanner Specifications . . . . . . . . . . . . . . . . . . . . . 7.3.1 SE 1223HP, LR, ALR And SE 955HP Specifications . 7.3.1.1 SE 1223HP Decode Zone . . . . . . . . . . . 7.3.1.2 SE 1223LR Decode Zone . . . . . . . . . . . 7.3.1.3 SE 1223ALR Decode Zone . . . . . . . . . . 7.3.1.4 SE 955HP Decode Zone . . . . . . . . . . . . 7.3.2 EV15 Imager Specifications . .
Chapter 7: Specifications WORKABOUT PRO G2 Note: Performance specifications are nominal & subject to change without notice. 7.1 WORKABOUT PRO G2 Dimensions • • WORKABOUT PRO C G2: 223mm x 75/100mm WORKABOUT PRO S G2: 220mm x 75/100mm x 31/42mm Weight (without battery) • • WORKABOUT PRO C G2: 450g WORKABOUT PRO S G2: 425g Operating System • Microsoft Windows Embedded CE 5.
Chapter 7: Specifications Radio Specifications Laser: IEC 60825-1:1993+A1:1997+A2:2001 Class 2 CDRH 21 CFR 1040 Class II 7.2 Radio Specifications Model RA2041: 802.11b/g Direct Sequence Spread Spectrum (DSSS) Form factor Antenna port Transmit Power Frequency Range Channels RX Sensitivity Data Rates Compact Flash Type I extended Two Hirose U.FL connectors for antenna diversity 802.11g: 32mW maximum (+15 dBm) 802.11b: 80mW maximum (+19 dBm) 2.400 - 2.
Chapter 7: Specifications Scanner Specifications 7.3 Scanner Specifications 7.3.1 SE 1223HP, LR, ALR And SE 955HP Specifications Scan Engine SE 1223HP SE 1223LR SE 1223ALR Scan Angle 42º ± 2º 23º ± 2º 13º ± 2º Scan Rate 35 (± 5) scans/sec (bi-directional) 35 (± 5) scans/sec (bi-directional) 35 (± 5) scans/sec (bi-directional) Scan Pattern Wavelength Linear 650nm Linear 650nm Linear 650nm Input Voltage 5.0 VDC ± 10% 5.0 VDC ± 10% 5.
Chapter 7: Specifications SE 1223HP Decode Zone 7.3.1.1 SE 1223HP Decode Zone 4,844 Lux to 86,112 Lux 7.3.1.2 Mil Size Minimum range Inches 5 2.75 Inches Maximum range Inches 1.25 7 3 Width of field Width of field Inches 7.5 2.25 1 11 4 10 1.75 0.5 15.75 6 UPC 2 1 22 9 15 2 1 25 10 20 2 1 30 12.5 40 3.75 56 23 55 5 66 25 SE 1223LR Decode Zone 4,844 Lux to 86,112 Lux Mil Size Minimum range Inches Inches Maximum range Inches 10 11 2 24 5 15 7.
Chapter 7: Specifications SE 1223ALR Decode Zone 7.3.1.3 SE 1223ALR Decode Zone 4,844 Lux to 86,112 Lux Minimum range Inches Inches Maximum range Inches 19 2 39 15 20 2 50 6 30 33 4 98 11 Mil Size UPC 55 Width of field Width of field Inches 4 27 2 115 12 70 reflective 114 12 250 28 100 reflective 125 14 360 41 High quality symbols in normal room light. 7.3.1.4 SE 955HP Decode Zone Decode Zone Typical 4 mil 1.0 in. - 5.5 in. / 2.54 cm - 13.97 cm 5 mil 1.25 in. - 8 in.
Chapter 7: Specifications EV15 Imager Decode Zone Parameter EV15 Reading Distance Up to 90cm (35 in) UPC (E&A), EAN, RSS, Code 39, Code 128, UCC/EAN 128, ISBN, ISBT, Interleaved, Matrix, Industrial and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI, Plessey, Telepen, PDF417, Micro PDF417 Works in any lighting conditions, from 0 to 100,000 lux 2000G, 0.7ms, half sinus, 3 axes 50G r.m.s Symbologies Ambient Light Shock Vibration 7.3.2.
Chapter 7: Specifications HHP5180 Imager Decode Zone Parameter HHP5180 2D: PDF417, MicroPDF417, MaxiCode, Data Matrix, QR Code, Aztec, Aztec Mesa, Code 49, UCC Composite Symbologies supported Linear: Code 39, Code 128, Codabar, UPC, EAN, Interleaved 2 of 5, RSS, Code 93, Codablock Postal: Postnet (US), Planet Code, BPO 4 State, Canadian Post, Japanese Post, KIX (Netherlands) Post Size Weight Operational Input Voltage: Current Draw: Operating Temperature Storage Temperature Humidity Shock 7.3.3.
Chapter 7: Specifications SX5393 Imager Performance 6.6 mil PDF417 (.017 cm) 7.5 mil Linear (.019 cm) 8.3 mil Data Matrix (.021 cm) 8.3 mil QR (.021 cm)6 10 mil Linear (.025 cm) 13 mil UPC (.033 cm) Near 2.8 in. (7.1cm) 2.5 in. (6.4cm) 3.4 in. (8.6cm) 3.4 in. (8.6cm)) 2.2 in. (5.6cm) 2.0 in. (5.1cm) Far 6 in. (15.2cm) 6.5 in. (16.5cm) 5.7 in. (14.5cm) 5.4 in. (13.7cm) 7.6 in. (19.3cm) 8.9 in. (22.6cm) SF Working Range* *Data characterized at 23°C and 0 lux ambient light. 7.3.
Chapter 7: Specifications SX5393 Imager Decode Zone 7.3.4.1 SX5393 Imager Decode Zone x Lux to 100,000 Lux Mil Size* Minimum range Inches Maximum range Inches 10 4.6 5.7 15 3.8 9.2 4 9.7 20.8 2.6 11.7 Minimum range Inches Maximum range Inches 15** *QR code **Data Matrix Code 39 Mil Size 7.5 4.1 8.4 10 3.1 10.9 15 4 9.7 WORKABOUT PRO G2 Hand-Held With Windows Embedded CE 5.
APPENDIX A PORT PINOUTS A.
Appendix A: Port Pinouts Tether Port Pinout A.
APPENDIX B WIRELESS WIDE AREA NETWORK (WWAN) B.1 Wireless WAN Psion Teklogix offers a quad band, GPRS radio – Model Number RA3030-G2; a WORKABOUT PRO G2 equipped with a GSM/GPRS radio has wide area networking capabilities. B.1.1 Taskbar Icons Wireless WAN icons in the taskbar indicate the status of your wide area network connection. Note that these icons are only visible when a GSM/GPRS radio is installed in the computer, and the interface is enabled.
Appendix B: Wireless Wide Area Network (WWAN) Establishing A Connection A new SMS message has arrived. B.1.2 Establishing A Connection To display the main Wireless WAN dialog box: • Double-tap on the Wireless WAN icon in the taskbar. If the icon is not visible in the taskbar, the radio interface has been shut down or the modem has been removed: • In the Control Panel, choose the Wireless WAN icon. Figure B.1 Wireless WAN Icon The main Wireless WAN dialog box is displayed. Figure B.
Appendix B: Wireless Wide Area Network (WWAN) Establishing A Connection Note: If you are prompted to enter a PIN, refer to “Entering A PIN Number” on page 4 for details. When “Ready to connect” is displayed in the Status field, the Connect Data button is enabled. • Tap on the Connect Data button. The progress of the connection is tracked in the Status field. • PPP link to modem active. • Authenticating user. • User authenticated. • Connected.
Appendix B: Wireless Wide Area Network (WWAN) Advanced Information B.1.3 Advanced Information In most cases, when a GSM/GPRS radio and SIM are installed in your computer, setup is automatic. Follow the steps outlined under the heading “Establishing A Connection” on page 2 to make a connection. The information in this section is for advanced setup purposes. Entering A PIN Number If a PIN is required, a PIN entry dialog box is displayed. • Note: Type your PIN, and press [ENTER].
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu • No network found. A network is not currently available. The modem continues searching for a network. • Packet data not available. The current network does not support a packet data service. • Packet data not allowed. The modem is not allowed to use the packet data service on the current network (e.g. no GPRS roaming agreement between network; a roaming agreement for voice may still be in place).
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu WWAN Data Configuration Enable Automatic Connect If the Enable automatic connect checkbox is checked (unchecked by default), the Wireless WAN user interface will attempt to establish a GPRS connection whenever GPRS is available (e.g. after resume from suspend without further user interaction). To activate the automatic connection mode: • Tap on the OK button.
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu Important: Automatic connection mode should not be used if applications other than the Wireless WAN user interface (e.g. Connection Manager) are expected to open and close connections. If the automatic connection mode is enabled and another application closes the GPRS connection, the WWAN user interface will immediately try to re-establish the connection.
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu Profiles In the following section, all the parameters that need to be configured for a connection (such as APN, user name, password, DNS server addresses etc.) are referred to as a profile. Every profile is identified by an arbitrary, unique name. The profile named Default is special in that it is always present and can neither be edited nor deleted. The Default profile uses parameters from a built-in database.
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu New Tapping on the New button allows you to create a new profile. Figure B.3 Creating A New Profile The name of the newly created profile must be different from all existing profiles. Also, the name cannot be Default. When the New Data Profile dialog box is opened, a proposal for a unique name is filled in the corresponding entry field.
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu Advanced IP Figure B.4 Assigning IP Information The Advanced IP button in the Show Profile and Edit Profile dialog boxes opens another dialog box that allows you to configure a static IP address as well as the IP addresses for the primary and secondary DNS server. Security Configuration The Security Configuration dialog box is accessed through the Tools menu. The Security Configuration dialog box allows you to enable, disable and change the PIN.
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu Network Configuration In the main Wireless WAN window: • Tap on the Tools menu, and choose Network. By default the GSM radio modem automatically chooses from the available and allowed networks (allowed networks are the home network and all other networks with which the home network has a roaming agreement). You may find there are some situations in which you want to override this default behaviour.
Appendix B: Wireless Wide Area Network (WWAN) Tools Menu Driver Mode Configuration By default, the Wireless WAN driver is enabled (the Enable driver checkbox is checked). The driver must be disabled in order to use the modem for anything other than GPRS (e.g. dial-up data, fax, or in order to manually submit AT commands to the modem for development, testing, approvals, etc.).
Appendix B: Wireless Wide Area Network (WWAN) SMS Menu B.1.5 SMS Menu SMS functions are accessed through the SMS menu. For modems that support a SIM card, the SIM initialization typically takes longer than the network initialization, resulting in a noticeable delay before the SMS functions become available. New Tapping on the New button opens a dialog for sending a new SMS message.
Appendix B: Wireless Wide Area Network (WWAN) Power Mode message list). Pressing the Reply button opens the new message dialog as described above, except the destination phone number is filled in already. Outbox Tapping on the Outbox button opens the list of sent messages. Otherwise the Outbox behaves exactly as the Inbox described above. The date and time when a message was sent is not available for GSM modems.
INDEX A Accepted Start Char 177 accessories belt loop (carrying case) 218 carrying case 218 desktop docking station 223 Ethernet adaptor cable 227 hand strap 215 holster, soft shell 220 pistol grip 217 port replicator 238 quad battery charger 229 quad docking station 232 single battery charger 228 swivel belt loop (carrying case) 218 vehicle cradle 235 Active Conn Tab 117 ActiveSync 227 ASync profile 113 Adaptive Windowing 194 adaptor cable USB-Ethernet 227 Addendum 182, 195, 196 Addendum Add-on 2 157, 158,
Index a description of 221 backup (ML2032) 12 capacity dialog box 101 charging 11, 37 gauge 48 installing 36 installing main battery 12 main battery 11 power saving suspend dialog box 101 removing 36 run time 49 storing 50 swap time 37 battery charger safety instructions 222–223 beeper beep conditions 46 volume adjustment 47 belt loop, swivel (carrying case) 218 Bi-Direction Redundancy 139 BKSP (DEL Key) 41 Bluetooth radio changing device name 117 device service profiles 113 ISM band 111 PINs for devices 11
Index Concatenation 162 connection list table, Bluetooth Controls 117 Constant Illumination 194 Contact 206 Continuous Scan Mode 138, 154, 175, 190 control panel accessing 81 basic setup 87 Display Properties 87 icons 83 keyboard properties 90 power management properties 100 stylus properties 104 Conv. UPC-E To UPC-A 147 Conv.
Index FNC1 Conversion 178 formatting entire memory card 129 partitions 132 Full Ascii 176 Full ASCII (decoded scanner) 142, 156 Function Keys accessing 42 G Good Scan Beep 202 GPRS (bluetooth) 118 GSM/GPRS E-1–E-12 GS1-128 178 GS1 128 (Composite bar code) 167 GS1-128 GS1 US 144 GS1-128 Identifier 178 GTIN Compliant 178, 182 H hand strap 215 holster, soft shell 220 I IATA 2 of 5 164 Imager EV15 specs 247 imager parameters 190 indicators battery gauge 48 docking devices 49 LED functions 46 modifier keys 48
Index Manage Triggers 106 Matrix 2 of 5 164, 186 Max Gain (Imager) 193 Max Illumination (Imager) 193 Maximum Length 155, 157, 161, 162, 163, 164, 165, 166, 167, 168, 169, 170, 171, 172, 173, 174 Max Integration (Imager) 193 Max Number Barcodes 191 memory card creating partitions 130 formatting entire 129 formatting partition 132 messages Scan Indicator 201 scanner warning message 201 Scan Result 201 Micro PDF-417 153, 169, 189, 198 Minimum Cancel Time 138, 154, 175 Minimum Length 155, 157, 161, 162, 163, 16
Index Command Prompt 66 Internet Explorer 66 Remote Desktop Connection 66 Windows Explorer 66 protective case 218 punctuation marks, accessing (SHIFT Key) 40 Q quad battery charger 229 quad dock (WA4004) 232 R radio Bluetooth 111 Bluetooth specs 244 IP address (Summit), assigning 13 name servers (Summit) 16 RA2041 radio specifications 244 specifications 244 802.11g Direct Sequence SS 244 802.
Index Decode Perf.
Index SIP (Soft Input Panel 83 Sled See vehicle cradle.
Index UPC Half Block Stitching, 2D 148 USB-Ethernet adaptor cable (WA4010) 227 User security level 65 Use Virtual Serial Port E-7 V vehicle cradle 235 powered 10-55 VDC 235 powered 12 VDC 235 unpowered 235 W warm reset 31 Warm Reset (Shutdown menu) 71 warnings 201 Window Height 191 Windows® Start Menu See Start Menu 63 Windows CE dialog box 72 files, folders, & programs, working with 58 Windows CE, navigating in 57 Windows Explorer 66 Windows Zero Config (WZC) 26 Window Width 191 Wireless WAN E-1–E-12 SMS
WORKABOUT PRO Hand-Held Computer Regulatory & Warranty Guide February 21, 2007 ISO 9001 Certified Quality Management System PN 8000126.
© Copyright 2007 by Psion Teklogix Inc., Mississauga, Ontario, Canada This document and the information it contains is the property of Psion Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Psion Teklogix manufactured goods and services.
Return-To-Factory Warranty Psion Teklogix provides a return to factory warranty on this product for a period of twelve (12) months in accordance with the statement of Warranty and Product Support provided at: www.psionteklogix.com/warranty. The warranty on Psion Teklogix manufactured equipment does not extend to any product that has been tampered with, altered, or repaired by any person other than an employee of an authorized Psion Teklogix service organization.
RoHS Logo Although there is no legal requirement to mark RoHS-compliant products, Psion Teklogix Inc. indicates its compliance with the directive as follows: The RoHS logo located either on the back of the product or underneath the battery in the battery compartment (or on a related accessory such as the charger or docking station) signifies that the product is RoHS-compliant as per the EU directive.
Table Of Contents 1. 2. 3. 4. Declaration Of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Support Services & Worldwide Offices . . . . . . . . . . . . . . . . . . . . . . 4.1 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Product Repairs . . .
1. Declaration Of Conformity Declaration of Conformity documents are provided at: www.psionteklogix.com/DoC 2. Safety Summary CE Marking When used in a residential, commercial or light industrial environment the product and its approved UK and European peripherals fulfil all requirements for CE marking. R&TTE Directive 1999/5/EC This equipment complies with the essential requirements of EU Directive 1999/5/EC (Declaration available: www.psionteklogix.com/DoC).
Deze apparatuur voldoet aan de noodzakelijke vereisten van EU-richtlijn betreffende radioapparatuur en telecommunicatie-eindappa-ratuur 199/5/EG. (verklaring beschikbaar: www.psionteklogix.com/DoC). Dette udstyr opfylder de Væsentlige krav i EU's direktiv 1999/5/EC om Radio- og teleterminaludstyr. (Erklæring findes på: www.psionteklogix.com/ DoC). Dette utstyret er i overensstemmelse med hovedkravene i R&TTE-direktivet (1999/5/EC) fra EU. (Erklæring finnes på: www.psionteklogix.com/DoC).
Acest echipament satisface cerinţele esenţiale ale Directivei UE 1999/5/EC (Declaraţia poate fi gasitã pe site-ul: www.psionteklogix.com/DoC) Oprema je skladna z bistvenimi zahtevami EU direktive 1999/5/EC (Deklaracija je na voljo: www.psionteklogix.com/DoC) Käesolev seade vastab EU Direktiivile 1999/5/EC (selgitus saadaval: www.psionteklogix.com/DoC) Az eszköz megfelel az EU 1999/5/EC fő direktíváinak (a nyilatkozat megtalálható: www.psionteklogix.
FCC Information To Users Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Some equipment in hospitals and aircraft are not shielded from radio frequency energy. Do not use the device onboard aircraft, or in hospitals, without first obtaining permission. Do not use near pacemakers. The product may affect the operation of some medically implanted devices such as pacemakers, causing them to malfunction. Avoid placing your product next to such devices.
Warning to Users This product is a Class I/Class II laser product according to CDRH 21 CFR 1040.10 and 1040.11 and Class1/Class 2 laser product according to IEC 60825-1:1993+A1:1997+A2:2001 Laser Warnings For your own safety, it is critical that you comply with the following warnings: Caution! Do not look into the laser beam or point the beam at people or animals. Caution! Using controls or adjustments, or performing procedures other than those specified herein may result in hazardous radiation exposure.
Safety Instructions for the following: • AC Wall Adaptor, • Desktop Docking Stations, and • Tether Cable For your own safety, it is critical that you comply with the following warnings: Caution! Before use, read all safety instructions for the Docking Station, the handheld and the AC Wall Adaptor. Caution! To avoid the risk of fire or personal injury, use only the Psion Teklogix recommended AC adaptor.
Caution! To reduce risk of electric shock, unplug the AC adapter from the outlet before attempting any cleaning. Caution! An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in fire or electric shock.
Warning: • • • • • • • • • • • • • • • 10 TO PREVENT the battery from leaking acid, generating heat or exploding, adhere to precautions below. The battery incorporates built-in safety devices. To ensure their proper function, do not disassemble or alter any parts of the battery. Do not short-circuit the battery by directly connecting any of the exposed terminals with metal objects such as wire. Do not transport or store the battery together with metal objects such as necklaces, hair pins, etc.
• • • Do not store the battery in extremely high temperatures (e.g., a vehicle, strong direct sunlight, etc.). This may cause the battery to overheat or ignite, and it may also reduce the performance and service life of the battery. Do not use in areas where static electricity is greater than what the manufacturer guarantees. Keep batteries out of reach of children. 4. Support Services & Worldwide Offices Psion Teklogix provides a complete range of product support services to its customers worldwide.
4.2 Product Repairs For repair service in North America: Call Toll free: +1 800 387 8898 Option 2 or Direct Dial: +1 905 813 9900 Ext. 1999 Option 2. For repair service in EMEA (Europe, Middle East and Africa), please contact the local office listed in the following website: http://www.psionteklogix.com/EMEASupport For repair service in Asia, please contact the local office listed in the website below: http://www.psionteklogix.com 4.3 Worldwide Offices COMPANY HEADQUARTERS Psion Teklogix Inc.
NORTH AMERICAN HEADQUARTERS AND U.S. SERVICE CENTRE Psion Teklogix Corp. 1810 Airport Exchange Boulevard Suite 500 Erlanger, Kentucky USA 41018 Tel: +1 859 371 6006 Fax: +1 859 371 6422 Email: salesusa@psion.com INTERNATIONAL SUBSIDIARIES (see also www.psionteklogix.com/Subsidiaries) Psion Teklogix S.A. La Duranne 135 Rue Rene Descartes BP 421000 13591 Aix-En-Provence Cedex 3; France Tel: +33 4 42 90 88 09 Fax: +33 4 42 90 88 88 E-mail: tekeuro@psion.