BlueTest Instruction Manual IF IQ MATCH Summary Measures IF IQ match by injecting test signal, sweeping IQ trim and measuring RSSI for on-channel and image. Returns array of IQ measurements against IQ trim. Return Data An array of 16 IQ measurements against IQ trim. Exit Click on Reset Chip. BlueCoreTM01 Title IF IQ MATCH Example Display bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual VCO TRIM Summary Produces look up table of VCO trim versus hop frequencies for a designated country hop sequence. Test Arguments Country Code Return Data An array of 79 values for VCO trim if Country Code is 0 otherwise 23 values. Exit Click on Reset Chip. BlueCoreTM01 Title (cc) = 0 to 3 (default = 0) VCO TRIM Example Display bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual BlueCoreTM01 Miscellaneous Test Routines Title Set PIO Summary Enables designated PIO lines as outputs and sets them as desired. To be used with caution since it over-rides previous settings. Bit 0 corresponds to PIO[0], and a logic one enables it as an output. Mask (default = 11111111) Test Arguments Values (default = 00000000) Return Data None Exit Click on Reset Chip.
BlueTest Instruction Manual Read PIO Summary Reads the logic state of the PIO pins. Valid whether they are inputs or outputs. Return Data PIO Lines (uint8) sent over BCSP channel 3, giving the logic level at each of the pins. Exit Click on Reset Chip. BlueCoreTM01 Title READ PIO Example Display bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual BUILD LUT Summary Builds the radio’s channel LO_TRIM frequency look-up table then returns it to the host. Return Data A sequence of 79 uint16 numbers, containing the calibration data just generated. Exit Click on Reset Chip. BlueCoreTM01 Title BUILD LUT Example Display bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual READ LUT Summary Reports the radio’s channel LO_TRIM frequency look-up-table (LUT) to the host. Return Data A sequence of 79 (uint16) numbers containing the contents of the look up table (LUT) for Europe and North America or a sequence of 23 (uint16) numbers for other countries. The upper byte contains the transmitter trim and the lower byte contains the receiver trim. Exit Click on Reset Chip.
BlueTest Instruction Manual PROVOKE FAULT Summary Provokes a fault mode in the on-chip processor. Return Data None BlueCoreTM01 Title Fault (hex) = 0 to 2b (default = 0) Test Arguments Note: Contact CSR for more information about using fault modes. Exit Click on Reset Chip. PROVOKE FAULT Example Display bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual READ CHIP VERSION Summary Reads the hardware ID and firmware version of device. Return data Hardware ID and firmware version. BlueCoreTM01 Title READ CHIP VERSION Example Display bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual Select PS from the main menu. Enter a Key number. To read a PS Key value, click on Read. The setting displays in the Value field. To change a PS key setting, enter a different value in the Value field and click on Set. PERSISTENT STORE KEY Example Display To exit, click on OK. bc01-an-047b © Copyright CSR Ltd 2001 This material is subject to CSR’s non-disclosure agreement.
FCC Regulations: zThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. zThis device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
BlueTest Instruction Manual BIST Parameters Name Type Min Max Meaning lo_freq uint16 2402 2480 Bluetooth channel frequency in MHz lxlvl uint16 0 63 Internal amplifier power setting.
BlueTest Instruction Manual Type Min chan1 uint16 0 78 Bluetooth channel number chan2 uint16 0 78 Bluetooth channel number n_samples uint16 0 65535 Number of samples in range from min to max for IF filter response test lo_offset uint16 0 65535 Min offset in 1/4096MHz for IF filter response test hi_offset uint16 0 65535 Max offset in 1/4096MHz for IF filter response test output_mask Uint8 0 FF Bit mask for PIO; 0=input, 1=output output Uint8 0 FF Bit values for PIO output
BlueTest Instruction Manual Known Software Issue(s) in BlueTest Version 1.4 (a) Pressing the Reset Chip button on the GUI while data is being transmitted sends a hardware reset command to the chip and restarts the serial stack software. Closing the GUI sends a hardware reset command to the chip.
BlueTest Instruction Manual Combining Tests Using a Second Unit READ CHIP VERSION PROVOKE FAULT READ PIO SET PIO READ LUT BUILD LUT VCO TRIM IF IQ MATCH RF IQ MATCH IF RESP SETTLE PCM LB PCM EXT LB DEEP SLEEP BER LOOP BACK LOOP BACK RX LOOP BACK BIT ERR2 BIT ERR1 RXDATA2 RXDATA1 RXSTART2 TXDATA3 TXDATA4 RXSTART TXDATA2 TXDATA1 TXSTART PAUSE RADIO STATUS SECOND UNIT Several tests require a second BlueCore01 unit to be operating to provide a test signal for the equipment under test
BlueTest Instruction Manual Configuration Commands Available During Tests CFG SETTLE CFG TX COMP CFG LO LVL CFG TX TRIM CFG IQ TRIM CFG ACC ERRS CFG UAP/LAP CFG XTAL FTRIM CFG TXIF CFG BIT ERR CFG PKT CFG FREQ Configuration Commands Particular configuration commands are appropriate to use during certain tests. The following table is a quick reference guide to which configuration commands can be used during which tests.
BlueTest Instruction Manual Bluetooth Packet Types Use the CFG FREQ command to set the frequency as appropriate to the size of the packet type being used in the test. Extracted from Packet Types section of Specification of the Bluetooth System, v1.1, dated 1 December 2000. bc01-an-047b © Copyright CSR 2001 This material is subject to CSR’s non-disclosure agreement.
BlueTest Instruction Manual CSR’s products are not authorised for use in life-support or safety-critical applications. Trademarks and Patents BlueCore is a trademark of CSR. Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG Inc, USA and licensed to CSR. CSR reserves the right to make technical changes to its products as part of its development programme. For further information, refer to the following document(s): Document Reference Bluetooth (SIG) Test Specification - RF Rev 0.
BlueTest Instruction Manual Date: Revision: 13 SEP 00 a 16 JUL 01 b BlueCoreTM01 Record of Changes Reason for Change: Original publication of this document (CSR reference: bc01-an-047a). Revision and addition of tests and appendices BlueTest Instruction Manual AN047 July 2001 bc01-an-047b © Copyright CSR 2001 This material is subject to CSR’s non-disclosure agreement.
