Chapter 5: Settings Manage Triggers • Tap on the Hardware tab, and choose a GPS hardware port and the appropriate Baud rate. Windows Mobile 6 automatically manages access to the GPS receiver. However, some programs may not work with automatic configuration. If this is the case: • Tap on the Access tab, and disable Manage GPS automatically (recommended). You can go to www.microsoft.com/pocketstreets if a map-viewing program is not included with your PDA, and copy the file to your PDA. 5.
Chapter 5: Settings Trigger Mappings • Tap on Start>Settings>System tab>Manage Triggers icon. 5.22.1 Trigger Mappings A trigger mapping is an association between a particular key on the keyboard and a driver or application, the module(s)– sometimes referred to as “trigger consumer(s)”–of the trigger source. Along with keyboard keys, trigger sources can also be grip triggers, external hardware triggers or software-based.
Chapter 5: Settings Trigger Mappings Show All Modules By default, the trigger mapping list only shows active mappings. Mappings for drivers or applications that are not currently active are not normally displayed. By checking this checkbox, all mappings, both active and inactive, are displayed. Add Tapping this button brings up the Add mapping dialog (see below), so that you can add new trigger mappings.
Chapter 5: Settings Trigger Mappings Note: It is possible to map the same source to different modules (trigger consumers—for example, to both the Imager and Non-Decoded Scanner. If so, both devices/operations will occur simultaneously. This is not recommended in most cases, especially with devices such as Imagers or RFID Readers. It is also possible to map different sources to the same module (trigger consumer)—for example, two different trigger keys can be mapped to the RFID File System.
Chapter 5: Settings Memory 5.23 Memory This applet allows you to view memory use, storage card memory allocation, and it allows you to manage opened programs. To display the options for this applet: • Tap on Start>Settings. Tap on the System tab followed by the Memory icon. 5.23.1 Main Tab This tab lists the memory allocated for file and data storage and for program storage. 5.23.2 Storage Card The Storage Card screen indicates the total storage card or RAM disk memory along with the amount in use.
Chapter 5: Settings Running Programs 5.23.3 Running Programs Running Programs behaves like the task manager found on your desktop PC, allowing you to activate or stop any running programs. • • 5.24 Highlight an application(s). To end an application, tap on the Stop button. Tap on Stop All if you want to shut down all running applications, or To activate an application, tap on the Activate button. Power Icon This icon allows you to view and manage battery use. • 122 Tap on Start>Settings.
Chapter 5: Settings Battery Tab 5.24.1 Battery Tab This tab allows you to view the remaining battery capacity of the battery. 5.24.2 Advanced Tab The Advanced tab allows you to manage battery consumption. On Battery Power When the iKôn PDA is operating on battery power, this option allows you to determine how long the unit will remain on when it is not in use.
Chapter 5: Settings Battery Details • Tap in the checkbox to the left of On battery power to enable this option. Tap in the dropdown menu to choose the number of minutes your unit can remain idle before it shuts down. On External Power When the PDA is drawing external rather than battery power, this option allows you to determine the number of minutes the unit will remain on when not in use. • Tap in the checkbox to the left of On external power to enable this option.
Chapter 5: Settings Built-In Devices 5.24.4 Built-In Devices Slot Power Status When you enable one or more of the card slots listed, power is supplied to the enabled slot(s). Built-In Devices Power Status This section of the dialog box allows you to enable (provide power) to the device(s) installed in your unit. Keep in mind that the content of this screen varies depending on the devices installed in your PDA. Tapping on OK activates your selections.
Chapter 5: Settings Suspend Threshold 5.24.5 Suspend Threshold This applet allows you to determine the amount of battery power that you want to reserve in the battery to protect the data stored in the iKôn PDA. 5.24.5.1 Suspend Threshold And Estimated Battery Backup The Estimated Battery Backup is the amount of battery power that is reserved to protect data until a charged battery can be installed in the PDA.
Chapter 5: Settings Wakeup Keys Tab 5.24.6 Wakeup Keys Tab This option allows you to define which key can be pressed to wake the PDA from a suspend state. If the Two key wakeup option is checked, the operator will need to press two keys ?? – [FN/BLUE][ENTER] – to switch the PDA on. 5.25 Regional Settings To display the Regional Settings screen, tap on Start>Settings, and then tap on the System tab followed by the Regional Settings icon.
Chapter 5: Settings Remove Programs • Tap on the dropdown menu to choose your language and region. Once you’ve selected a language and region, you may need to adjust the way numbers, currency, the time and the date appear in your iKôn PDA. • 5.26 Tap on the tab associated with each of the items and choose how each item will be displayed on your iKôn PDA. Remove Programs • Tap on Start>Settings. Tap on the System tab followed by the Remove Program icon.
Chapter 5: Settings Scanner Settings • Tap Start>Settings. Tap on the System tab, and then tap on the Screen icon. Important: Refer to “Aligning (Calibrating) The Touchscreen” on page 14 for details about this option. 5.28 Scanner Settings The Teklogix Scanners icon in the Settings menu provides access to dialog boxes in which you can tailor bar code options and choose the bar codes your scanner will recognize.
Chapter 5: Settings Scanner Settings • Tap on Start>Settings, and then tap on the System tab followed by the Teklogix Scanner icon. Scanner Menu The dropdown menu to the right of the Scanner option allows you to choose from one of the following scanner types used with your PDA: Decoded (internal), Decoded (HHP), Decoded (Intermec ISCP) and Imager. The symbologies listed change to reflect the scanner you choose and the bar codes it supports.
Chapter 5: Settings Decoded (Internal) Scanners Options–Decoded (Internal) Scanner 5.28.1 Decoded (Internal) Scanners 5.28.1.1 Options–Decoded (Internal) Scanner Dot Time (msec) The value selected for “Dot Time (msec)” determines (in milliseconds) how long the targeting dot remains on before the scanner switches to a normal scan sweep. When you doubletap on this parameter, a dialog box is displayed in which you can enter a value of 0 msec, 200 msec or 400 msec. A value of 0 (zero) disables the target dot.
Chapter 5: Settings Decoded (Internal) Scanners Decoded (Internal) Advanced Options 5.28.1.2 Decoded (Internal) Advanced Options Continuous Scan Mode Setting this parameter to ‘on’ keeps the laser on and continuously decoding as long as the scanner button is pressed and held down. Minimum Cancel Time The value assigned to this parameter determines the time delay before the scanner is turned off, once the scanner trigger or button is released.
Chapter 5: Settings Decoded (Internal) Scanners Decoded (Internal) 2D Scanning Options MSI Plessey 4 or less D 5 of 5 8 or less I 2 of 5 8 or less “Linear security level 2” specifies that all types of codes must be successfully read twice before being decoded. “Linear security level 3” specifies that code types other than the following must be successfully read twice before being decoded.
Chapter 5: Settings Decoded (Internal) Scanners Data Options–Decoded (Internal) Scanner Note: These parameters are only used when either Programmable Raster or Always Raster is assigned to the “2D Scanning Mode” parameter. “2D Raster Height” and “2D Raster Expand Rate” are intended for very specific applications and are usually not required for normal scanning purposes. Double-tapping on this parameter displays a dialog box in which you can enter a value from 1 to 15. 5.28.1.
Chapter 5: Settings Decoded (Internal) Scanners Code 39 ECI Decoder Setting this parameter to on enables the scanner to interpret any Extended Channel Interpretations (ECIs) supported by the scanner. This parameter has no effect on symbols that were not encoded using ECIs. If this parameter is set to off and a symbol that was encoded using an ECI escape is scanned, the scanner transmits the ECI escape followed by the uninterpreted data. 5.28.1.
Chapter 5: Settings Decoded (Internal) Scanners Double-tapping on this parameter displays a dialog box labelled Set Code Lengths where you can define the code length that will be decoded by your scanner. Choosing One discrete length allows you to decode only those codes containing a selected length. Choosing Two discrete lengths allows you to decode only those codes containing two selected lengths. Length within a range allows you to decode a code type within a specified range from 1 to 55.
Chapter 5: Settings Decoded (Internal) Scanners Field Size/Chars Decode Perf. Level This parameter provides three levels of decode performance or “aggressiveness” for Code 39 symbols. Increasing the performance level reduces the amount of required bar code orientation – this is useful when scanning very long and/or truncated bar codes. Keep in mind that increased levels reduce decode security.
Chapter 5: Settings Decoded (Internal) Scanners Code 128 5.28.1.7 Code 128 Enabled Set this parameter to on to enable “Code 128”. Enable GS1-128/GS1 US Previously UPC/EAN and UCC, these types of bar codes include group separators and start codes. Enable ISBT 128 To successfully scan this variation, “Enable ISBT 128” must be set to on. Decode Performance If this parameter is set to on, one of three decode levels assigned to the “Decode Performance Level” parameter can be selected. Decode Perf.
Chapter 5: Settings Decoded (Internal) Scanners EAN 8 Suffix Char This character, if non-zero, is added after a successfully decoded bar code. Press the key you want to insert in the dialog box attached to this parameter. The ASCII/Unicode key value of the keypress is displayed. Strip Leading This parameter determines the number of characters that will be removed from the beginning of the bar code before the prefix character is added. Note: The appended character is treated as any other keyboard character.
Chapter 5: Settings Decoded (Internal) Scanners UPC E UPC-A, Preamble When you double-tap on this parameter, a dialog box is displayed where you can choose one of three options for lead-in characters for UPC-A symbols transmitted to the host device: System Char – system character transmitted with the data, Country code and System Char – both the country code (“0” for USA) and system character are transmitted with the data or None – no preamble is transmitted.
Chapter 5: Settings Decoded (Internal) Scanners UPC/EAN Shared Settings Prefix/Suffix Refer to page 137 for details. 5.28.1.13UPC/EAN Shared Settings The parameters you set here are a shared across all available UPC and EAN bar codes. Enable Bookland EAN Setting this parameter to on allows your scanner to recognize “Bookland EAN” bar codes. Supplementals 'Supplementals” are additionally appended characters (2 or 5). Double-tapping this parameter displays a list of options.
Chapter 5: Settings Decoded (Internal) Scanners Code 93 2D UPC Half Block Stitching Setting this parameter to on enables “UPC Half Block Stitching” for the SE 3223 omnidirectional engine only. 5.28.1.14Code 93 Enabled Set this parameter to on to enable “Code 93” or off to disable it. Set Length L1 And Set Length L2 Lengths for “Code 93” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e.
Chapter 5: Settings Decoded (Internal) Scanners MSI Plessey CLSI Editing When enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar symbol. Note: Symbol length does not include start and stop characters. NOTIS Editing When enabled, this parameter strips the start and stop characters from decoded Codabar symbol. Field Size/Char Refer to page 137 for details. 5.28.1.
Chapter 5: Settings Decoded (Internal) Scanners Interleaved 2 of 5 Note: If Two check digits is selected, an MSI Plessey “Check Digit Algorithm: must also be selected. See below for details. Transmit Check Digit If this parameter is enabled, the check digit is included with the bar code data. Check Digit Algorithm When the Two MSI Plessey check digits option is selected, an additional verification is required to ensure integrity.
Chapter 5: Settings Decoded (Internal) Scanners Discrete 2 of 5 Convert To EAN 13 If this parameter is enabled, the I 2 of 5 bar code is converted to EAN 13. Field Size/Char Refer to page 137 for details. 5.28.1.18Discrete 2 of 5 Enabled Set this parameter to on to enable “Discrete 2 of 5”. Set Length L1 And Set Length L2 Lengths for “Discrete 2 of 5” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e.
Chapter 5: Settings Decoded (Internal) Scanners Composite Enable RSS Expanded “RSS Expanded” uses the same application identifiers as UCC/EAN-128 codes but it can be split into sections and stacked several rows high, reducing the length of the symbol, while increasing the capacity of data that can be stored. “RSS Expanded” code can be omni-directionally scanned. Field Size/Char Refer to page 137 for details. 5.28.1.
Chapter 5: Settings Decoded (Internal) Scanners Micro PDF-417 5.28.1.22Micro PDF-417 Enable Setting this parameter to on enables “Micro PDF-417” bar code scanning. Micro PDF-417 is a multi-row symbology that is useful for applications requiring greater area efficiency but lower data capacity than PDF-417. Code 128 Emulation When this parameter is enabled, the scanner transmits data from certain Micro PDF-417 symbols as if it was encoded in Code 128 symbols.
Chapter 5: Settings Decoded 5.28.2 Decoded • Tap on the Scanner dropdown menu, and choose Decoded (Intermec ISCP). 5.28.2.1 Options–Decoded Scanner Laser On Time The value assigned to this parameter determines how long the laser will remain on when the scan button or trigger is pressed. Double-tapping on this parameter displays a dialog box in which you can enter a value between 1 and 10 seconds. 5.28.2.
Chapter 5: Settings Decoded Low Power Timeout To extend laser life, you can select the length of time the scanner remains active following a successful decode. The scanner wakes from low power mode when a bar code is scanned – a successful decode restores normal blinking. When you double-tap on this parameter, a dialog box is displayed in which you can choose a value of 30 sec, 1 min, 2 min or 3 min.
Chapter 5: Settings Decoded Start/Stop Transmit Setting this parameter to on enables the transmission of start and stop characters, which are usually not transmitted. Code 39 can start and end with either a * or a $ character (see also next parameter Accepted Start Char). Accepted Start Char This parameter allows the user the option of using one of the two start/stop characters or both ($ char, * char, $ and * char).
Chapter 5: Settings Decoded GS1-128 Identifier “GS1-128 Identifier” allows the AIM ID " ]C1" for EAN 128 to be transmitted or removed. By default, this identifier is transmitted if EAN 128 is enabled. GTIN Compliant GTIN (global trade item number) processing transmits EAN 128 as the 14-character EAN/UCC GTIN. To use GTIN processing, you must activate the EAN 128 symbology. Important: When EAN 128 and GTIN processing are both activated, it is not possible to read normal EAN 128 Codes.
Chapter 5: Settings Decoded Check Digit Verification The available options for this parameter are Disabled or French CIP. This parameter uses the specified algorithm of the option you've chosen to ensure the integrity of the symbol data before transmitting. If the data does not contain that algorithm, the data is not transmitted. Note: French CIP (French pharmaceutical) is only used with bar codes containing 7 characters. Minimum Length Minimum lengths for the bar code can be set from 0 to 255.
Chapter 5: Settings Decoded Convert To EAN 13 If this parameter is enabled, an EAN 8 bar code is converted to EAN 13. Prefix/Suffix Refer to page 137 for details. 5.28.2.7 UPCA Enabled Set this parameter to on to enable “UPC A” bar code scanning recognition. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Transmit Number System If this parameter is enabled, the number system digit is transmitted with the decoded bar code data.
Chapter 5: Settings Decoded Convert To UPC-A This parameter converts UPC E (zero suppressed) decoded data to UPC A format before transmission. After conversion, data follows UPC A format and is affected by UPC A programming selections (e.g. Check Digit). Prefix/Suffix Refer to page 137 for details. 5.28.2.9 UPC/EAN Shared The setting assigned to the “Addendum” parameter associated with this option is shared across all UPC and EAN bar codes.
Chapter 5: Settings Decoded Reading Range This parameter determines the reading distance from which a bar code can be successfully scanned. The default setting, Extended, allows for increased reading distance. 5.28.2.10Code 93 Enabled Set this parameter to on to enable “Code 93”. Minimum Length Minimum lengths for the bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
Chapter 5: Settings Decoded Check Digit Verification When enabled, this parameter checks the integrity of a symbol to ensure it complies with a specified algorithm – either USS (Uniform Symbology Specification) or OPCC (Optical Product Code Council). Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Set Length L1, Set Length L2, And Set Length L3 Lengths for “Codabar” can be set from 0 to 255.
Chapter 5: Settings Decoded Plessy Transmit Check Digit If the check digit is to be transmitted with the Plessy data, this parameter must be enabled. Minimum Length Minimum lengths for the bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Plessy Minimum Length Minimum lengths for the Plessy bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e.
Chapter 5: Settings Decoded 5.28.2.14Interleaved 2 of 5 Enabled Set this parameter to on to enable “Interleaved 2 of 5”. Reading Range This parameter determines the reading distance from which a bar code can be successfully scanned. The default setting, Extended, allows for increased reading distance. Check Digit Verification The available options for this parameter are Disabled, MOD 10 Check and French CIP.
Chapter 5: Settings Decoded Minimum Length Minimum lengths for the bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Field Size/Char Refer to page 137 for details. 5.28.2.16Discrete 2 of 5 Enabled Set this parameter to on to enable “Discrete 2 of 5”. Standard 2 of 5 Format This parameter allows you to choose a standard format – either Identicon (6 start/stop bars) or Computer Identics (4 start/stop bars).
Chapter 5: Settings Decoded 5.28.2.17Telepen Enabled Set this parameter to on to enable “Telepen”. Format This parameter allows you to set the bar code character format to either ASCII or Numeric. Minimum Length Minimum lengths for the bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Field Size/Char Refer to page 137 for details. 5.28.2.
Chapter 5: Settings Decoded Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.2.19PDF-417 Enabled Set this parameter to on to enable “PDF-417”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.2.20Micro PDF-417 Enabled Set this parameter to on to enable “Micro PDF-417”. Code 128 Emulation When this parameter is enabled, the scanner transmits data from certain Micro PDF-417 symbols as if it was encoded in Code 128 symbols.
Chapter 5: Settings Imager Enable Codablock F Set this parameter to on to enable “Codablock type F”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3 Imager • Tap on the Scanner dropdown menu, and choose Imager. 5.28.3.1 Options–Imager TekImager Enabled Setting this option to on enables the imager installed in your PDA. Continuous Scan Mode Setting this parameter to on keeps image capture active and continuously decoding as long as the scanner button is pressed and held down.
Chapter 5: Settings Imager rameter is set to on, the target dot is pointed at the centre image and only that image is returned. Max Number Barcodes This parameter specifies the maximum number of bar codes the imager will attempt to decode in an image. A maximum of 6 bar codes can be decoded at one time. Barcodes Must Decode This parameter specifies the minimum number of bar codes that the imager must decode in order to report success.
Chapter 5: Settings Imager Factory Defaults On Reboot The value assigned to this parameter determines whether or not the driver will restore the factory defaults to the imager device on the next reboot. Note: The driver will default the imager device on a ‘clean’ reset, regardless of the value of this parameter. Min Scan Duration This parameter defines the minimum amount of time in seconds that the imager will scan when the trigger is pressed and held down without successful decode.
Chapter 5: Settings Imager Fast Converge Note: “Auto Exposure” must be set to ‘on’ in order for this parameter to function. Keep in mind that while this parameter can improve imager performance, “Fast Converge” increases battery power consumption. Setting this parameter to on speeds the “Auto Exposure” process. It allows the imager to rapidly snap a number of bar code capture attempts while finding ideal values for gain, integration and illumination.
Chapter 5: Settings Imager Note: This feature assumes that you have reached an understanding about how the device operates in your application, and that, after a learning period, operators will get used to using the imager in one particular way. It also assumes that a trained operator will usually only have near miss scenarios. Constant Illumination “Constant Illumination” is used to reduce the intrusiveness of the device’s illumination on the observer.
Chapter 5: Settings Imager • Highlight an item, and tap on OK. When “Addendum” is set to Disabled, the scanner does not recognize an addendum. If this parameter is set to Optional, the scanner searches for an addendum and if one exists, appends it to the main bar code. When the parameter is set to Required, the scanner does not accept the main bar code without an addendum. Note: Setting “Addendum” to ‘Optional’ reduces performance.
Chapter 5: Settings Imager Addendum Refer to page 154. Prefix/Suffix Refer to page 137 for details. 5.28.3.9 Code 93 Enabled Set this parameter to on to enable “Code 93”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.10Codabar Enabled Set this parameter to on to enable “Codabar”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.11Interleaved 2 of 5 Enabled Set this parameter to on to enable “Interleaved 2 of 5”.
Chapter 5: Settings Imager 5.28.3.13Composite Important: To successfully read this type of bar code, the two types of symbologies included in a composite bar code must be enabled. Enabled Set this parameter to on to enable “Composite” bar codes. 5.28.3.14PDF-417 Enable Setting this parameter to on enables PDF-417 two dimensional (2D) coding. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.15Micro PDF-417 Enable Setting this parameter to on enables “Micro PDF-417” bar code scanning.
Chapter 5: Settings Imager Field Size/Char Refer to page 137 for details. 5.28.3.182D Maxicode Enabled Set this parameter to on to enable “2D Maxicode”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.192D Aztec Enabled Set this parameter to on to enable “Aztec”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.20Postal: PlaNET Enabled Set this parameter to on to enable “Postal: PlaNET”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.
Chapter 5: Settings Imager Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.23Postal: Japanese Enabled Set this parameter to on to enable “Postal: Japanese”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.24Postal: Korean Enabled Set this parameter to on to enable “Postal: Korean”. Field Size/Char Refer to “Field Size” on page 137 for details. 5.28.3.25Postal: Royal Enabled Set this parameter to on to enable “Postal: Royal”.
Chapter 5: Settings Options Tab 5.28.4 Options Tab This tab allows you to tailor the double-click parameters and the display options associated with your scanner. 5.28.4.1 Double Click Parameters Click Time (msec) This parameter controls the maximum gap time (in milliseconds) for a double-click. If the time between the first and second clicks of the scanner trigger is within this time, it is considered a double-click. The allowable range is 0 to 1000. A value of zero disables this feature.
Chapter 5: Settings Options Tab 5.28.4.2 Display Parameters Scan Result When this parameter is enabled, the type of bar code and the result of the scan appear on the screen. Note that this information is only displayed after a successful decode and is visible only while the scanner trigger is pressed. When the trigger is released, this information is cleared from the screen. Scan Indicator When this parameter is enabled, the laser warning logo appears on the display whenever the scanner is activated.
Chapter 5: Settings Translations Tab 5.28.5 Translations Tab The Translations tab allows you to define up to 10 cases, each consisting of up to 10 rules in sequential order. Only one case will be applied to a bar code and a case will only be applied if all rules specified in the case are successful – if a rule within a case fails, the entire case fails. • 174 In the Translation tab, tap on the Case # to create rules.
Chapter 5: Settings Translations Tab • Tap on the No rule dropdown menu to display the rules. When you choose a rule, an associated screen is displayed in which you can define the rule. 5.28.5.1 Case Rules The case rules are defined as follows: • • • • • No rule – ignored. Match at index – matches the match string at a specified index. Match and replace at index – matches the match string at a specified index and replaces/changes it.
Chapter 5: Settings Total Recall • • Verify barcode size – verifies the bar code size. This rule should generally be assigned first, before creating subsequent rules. Search and replace – replaces all instances of the match string. (Note that this rule cannot fail.) Warning: Keep in mind that the effects of previously applied rules must be taken into account when creating subsequent rules.
Chapter 5: Settings Creating A Backup Profile • Tap on Start>Settings. Tap on the Total Recall icon. In the dropdown menu, you can choose: Create Backup Profile, Restore Selected Profile, View Selected Profile Data, and Delete Selected Profile. Keep in mind that until a profile is created, only one option is available–Create Backup Profile. 5.29.1 Creating A Backup Profile • Tap on the Next button to begin the process.
Chapter 5: Settings Creating A Backup Profile • • • • • • Next, choose the Profile Type you want to create: For this device only – creates a backup that is manually restored by the operator. AutoRestore for this device only – creates a profile that automatically restores itself following a cold start.
Chapter 5: Settings Creating A Backup Profile View Selections Depending on what you have selected for inclusion in your profile, you can view a list of all files, selected files, databases, and/or the registry. • If you’re satisfied with the items in the profile, tap on Next. Performing The Backup • Tap on Backup to begin the process and create a profile. When the backup is finished, a dialog box is presented stating that the backup has been completed successfully.
Chapter 5: Settings Restoring A Profile 5.29.2 Restoring A Profile To manually restore a profile: • • 5.30 Choose Restore Selected Profile from the dropdown menu, and choose the Profile Name you want to restore. In the next screen, tap on Restore to restore your profile. Connections Tab This tab is used to setup connections using Bluetooth, 802.11 radios, and you can also set up Wireless WAN connections. The Wireless WAN icon is only visible when Windows Mobile 6 Classic is installed in your iKôn PDA.
Chapter 5: Settings Connections Tab • Tap on Start>Settings>Connections tab to display your connection options. Navigation Bar Tap on these connectivity hotkeys to display Notification Bubbles Notification Bubble Navigation Bar Connectivity Hotkeys Some of the connectivity icons in the Navigation Bar along the top of the screen are hotkeys that offer shortcuts to connection setups.
Chapter 5: Settings Beam Automatic Network Detection If a wireless network is available when you switch on your unit, a notification bubble may appear letting you know which networks have been found. You can choose a network from here. Tapping on Connect in the softkey bar at the bottom of the screen will automatically connect to a network that’s already been set up. Tapping on Settings in the network bubble will launch the Wireless Manager applet.
Chapter 5: Settings The Devices Tab 5.32.1 The Devices Tab This tab allows you to scan for other Bluetooth enabled devices, and it allows you to pair devices. Note: You may need to enable your Bluetooth radio before you begin. Refer to “Bluetooth Mode” on page 185 for details. To add a new device: • Tap on Add new device.... The iKôn PDA scans for a Bluetooth device within a 10 meter range.
Chapter 5: Settings The Devices Tab • Highlight the device you want to add. Tap on Next. • • • Type your Passcode. Tap on Next. In the Display Name screen, edit the name of the device. This is optional. Tap on Finish. Note: To connect to a Bluetooth-equipped device that’s already been added, tap on the item in Bluetooth list box. 5.32.1.
Chapter 5: Settings Bluetooth Mode 5.32.2 Bluetooth Mode • Tap Start>Settings. Tap on the Connections tab>Bluetooth icon and then tap on the Mode tab. When Turn on Bluetooth is enabled (a checkmark is displayed in the checkbox), Bluetooth features are available. If this option is disabled, you cannot send or receive information using Bluetooth.
Chapter 5: Settings Outgoing Port New Incoming Port The Bluetooth COM Ports dialog box allows you to assign a COM port number. If a port number has not been assigned, tapping on New Incoming Port allows you to choose a COM port number. If a port number already exists that you’d like to change, tap and hold the stylus on Incoming Port (COM #) to display a pop-up menu. Choose Edit and assign a new COM port number.
Chapter 5: Settings Active Connections List of your PDA so that you are prompted to choose the device with which you want to communicate. 5.32.5 Active Connections List This tab displays the currently active Bluetooth connections, listing the device name(s). The type of link is also included with the device name(s). Keep in mind that the information listed in this tab is ‘view only’; it cannot be edited. 5.32.
Chapter 5: Settings The Bluetooth GPRS Phone 5.32.7 The Bluetooth GPRS Phone Once you’ve completed the Bluetooth settings, you can go ahead and set up communication through your Bluetooth-equipped phone. Before you begin, make certain that the Bluetooth phone is turned on, that the Bluetooth radios in your iKôn PDA and phone are enabled (turned on), and that the PDA and phone are within 10 metres of each other. Both should be discoverable. 1. Tap on Start>Settings and then tap on the Connections tab. 2.
Chapter 5: Settings Connections – Connecting To The Internet 14. In the User name, Password and Domain fields, enter the logon information for this connection, and tap on Finish. You can begin using the Bluetooth phone connection, for example, to send and receive email, browse the Internet with Internet Explorer, and so on. 5.33 Connections – Connecting To The Internet To activate a connection, make certain that any necessary equipment is installed in your PDA such as a radio.
Chapter 5: Settings Modem Connection Setup 4. In the Select a modem dropdown menu, choose a modem connection. If you haven’t already created a modem connection, refer to “Modem Connection Setup” on page 190. 5. To connect to the Internet, launch the program you want to use. For example, launch Internet Explorer on your iKôn PDA to browse the Internet. Your PDA automatically connects. Note: To set up a network card or wireless network connection to your ISP, add a new connection under My Work Network. 5.
Chapter 5: Settings Modem Connection Setup 5. Tap on the Next button. 6. In the next screen, enter the phone number exactly as you want it dialed. If, for example, you need to dial 9 for an outside line, enter 9 at the beginning of the phone number. 7. Tap on the Next button. 8. Type the User Name, Password and Domain Name as provided by your ISP or network administrator.
Chapter 5: Settings Modem Connection Setup Note: Generally, you will not need to change any of the Advanced settings. For information about the Advanced settings, refer to“Advanced Modem Settings” Changes to Advanced settings are only required in the following instances: To change the baud rate settings, dialing string commands or credit card options. To change port settings. To enter TCP/IP settings because the server to which you are connecting does not dynamically assign addresses. 9.
Chapter 5: Settings Wireless Power Icon Server Settings Tab If your server assigns IP addresses dynamically, you will not need to change these settings. Servers requiring assigned IP addresses may also need a way to map computer names to IP addresses. The iKôn PDA supports a variety of name resolution options: DNS, Alt DNS, WINS and Alt WINS. Your ISP or network administrator can determine which name resolution you need, and can also provide the server address.
Chapter 5: Settings Flight Mode – Disabling Wireless Components Important: The ‘Wireless Power’ option provides detailed Help files to assist you in setting up your PDA. Help is available from the Connections tab–not from within the Wireless Power dialog box. To access Wireless Power help files, tap on Start>Settings>Connections tab. Tap on Start>Settings>Help. • Tap on Start>Settings>Connections tab>Wireless Power icon. 5.34.
Chapter 5: Settings Setting Up A Network Card 5.34.2 Setting Up A Network Card Network (802.11) cards are used to connect to a network so that you can browse the Internet, download e-mail and so on. You can connect to an existing network or you can set up a new connection on your iKôn PDA. Important: The iKôn PDA is equipped with context sensitive Help Files.
Chapter 5: Settings Changing Network Card Settings • If you need to specify server information, double-tap on the appropriate adaptor, and then tap on the IP Address and/or Name Servers tab. Note: Because most networks use DHCP, you should not need to change these settings unless instructed to do so by your network administrator. • • If necessary, use a network cable to connect the network card to your network. Refer to the documentation shipped with your network card for details.
Chapter 5: Settings Managing An Existing Connection • • • • • • In Host name/IP, type the VPN server name or IP address. Tap on the VPN type radio button next to the type of authentication for your iKôn PDA: IPSec/L2TP or PPTP. Your network administrator will let you know which option applies to your unit. Tap on Next. Choose the type of authentication in this screen. If you choose A pre-shared key, type the key provided by your network administrator. Tap on Next.
Chapter 5: Settings Managing An Existing Connection • Tap on Manage existing connections. Tap here • • To launch a connection from this screen, press and hold the stylus on the connection you want to activate. Choose Connect from the pop-up menu. To delete a connection, press and hold the stylus on the connection you want to delete. Choose Delete from the pop-up menu. Note: You can also create a new connection by tapping on the New button.
Chapter 5: Settings Selecting A Network • Tap on the General tab. • • Type the name you prefer in the field below Enter a name for these settings. Tap on OK. 5.34.7 Selecting A Network Important: Normally, you will not need to change these settings. Contact your ISP or network administrator before making any changes. Private networks are used for work-related activities. Internet networks are used for home connection to your ISP.
Chapter 5: Settings Proxy Server Setup • Tap on the Advanced tab. • • Tap on Select Networks. In the appropriate lists, choose My ISP or My Work Network. 5.34.8 Proxy Server Setup Note: If you are connected to your ISP or private network during synchronization, the iKôn PDA will download the appropriate settings during synchronization from your PC. If these settings are not on your PC, or if they need to be changed, you’ll need to set up the proxy server connection manually.
Chapter 5: Settings Proxy Server Setup • Under My Work Network, tap on Set up my proxy server. • Add a checkmark next to This network connects to the Internet and This network uses a proxy server to connect to the Internet. In the Proxy server field, type the proxy server name. Tap on OK to save your changes. • • Note: If you need to change advanced settings such as a port number or proxy server type, you’ll need to tap on the Advanced button rather than tapping on OK.
Chapter 5: Settings Wireless Statistics • • 5.35 Tap on the proxy type you want to change. For the appropriate server type, type the proxy server name and port. Tap on OK. Wireless Statistics • • 5.36 Tap on Start>Settings>Connections tab>Wireless Statistics icon to display the communication statistics of your wireless connection along with the radio card name, MAC address, driver version and NDIS Compliance information. Tap on the Zero button to reset the statistics.
Chapter 5: Settings Establishing A Connection Signal strength is between 81% and 100%. A GPRS packet data connection is active. CDMA/1xRTT Signal strength is between 1% and 20%. Signal strength is between 21% and 40%. Signal strength is between 41% and 60%. Signal strength is between 61% and 80%. Signal strength is between 81% and 100%. A CDMA/1xRTT packet data connection is active. 5.36.2 Establishing A Connection • Tap on Start>Settings. Tap on the System tab followed by the Wireless WAN icon.
Chapter 5: Settings Disconnecting From A Network • • • • PPP link to modem active Authenticating user User authenticated Connected Note: Keep in mind that these states may be displayed fairly quickly if the progress of the connection is rapid. When the connection state reaches PPP link to modem active, the softkey bar icon changes to indicate an active connection. The Connect Data button changes, displaying Disconnect. 5.36.
Chapter 5: Settings Advanced Information • Type your PIN, and press [ENTER]. Note: If you exceed the number of allowable attempts, a PUK entry window is brought to the foreground. You’ll need to enter a new PIN number. Once the correct PIN or PUK is entered or if none was required, the modem is instructed to perform a GSM network registration followed by a GPRS attach. The main Wireless WAN dialog box reflects the progress of the initialization.
Chapter 5: Settings Tools Menu • SIM is missing The SIM card is missing. After the SIM has been inserted a reset may be required. • SIM failure The SIM card is permanently disabled (e.g. because the wrong PUK has been entered too many times). A new SIM is needed. • Modem failure The modem did not respond to commands as expected. If a reset does not clear this condition, the modem may need to be replaced. • NDIS error An internal software error has occurred.
Chapter 5: Settings Tools Menu • Tap on the OK button. While automatic connection mode is enabled, the Connect Data button in the main Wireless LAN dialog box changes to Disable Auto. To close the currently active connection (if any) and disable the automatic connection mode: • Tap on Disable Auto. Important: Automatic connection mode should not be used if applications other than the Wireless WAN user interface (e.g. Connection Manager) are expected to open and close connections.
Chapter 5: Settings Tools Menu Important: For CDMA/1xRTT, automatic configuration is not available – connections must be configured manually. Under APN, the packet service access number must be entered (typically “#777”). In the following section, all the parameters that need to be configured for a connection (such as APN, user name, password, DNS server addresses etc.) are referred to as a profile. Every profile is identified by an arbitrary, unique name.
Chapter 5: Settings Tools Menu • New – Tapping on the New button allows you to create a new profile. The name of the newly created profile must be different from all existing profiles. Also, the name cannot be Default. When the New Data Profile dialog box is opened, a proposal for a unique name is filled in the corresponding entry field.
Chapter 5: Settings Tools Menu • Advanced IP – The Advanced IP button in the Show Profile and Edit Profile dialog boxes opens another dialog box that allows you to configure a static IP address as well as the IP addresses for the primary and secondary DNS and WINS resolvers. 5.36.5.2 Security Configuration The Security Configuration dialog box is called up through the Tools menu. Note: Security configuration is not available with CDMA modems.
Chapter 5: Settings Tools Menu If unauthorized access to the device is a concern, the Require PIN on resume checkbox should be checked. In this case, you will be prompted whenever a PIN is required and the PIN is not stored. 5.36.5.3 Network Configuration Note: Network configuration is not available with CDMA modems. In the main Wireless WAN screen: • Tap on the Tools menu, and choose Network.
Chapter 5: Settings Tools Menu 5.36.5.4 Driver Mode Configuration By default, the Wireless WAN driver is enabled (the Enable driver checkbox is checked). The driver must be disabled in order to access the modem directly (e.g. dial-up data, fax, or in order to manually submit AT commands to the modem for development, testing, approvals, etc.). In most cases, the Virtual WWAN serial port can be used and it is not necessary to disable the WWAN driver.
Chapter 5: Settings Tools Menu SIM, the Phone field remains empty. The modem serial number is called IMEI for GSM modems and ESN for CDMA modems. The SIM ID is sometimes referred to as the ICC ID (International Charge Card Identifier). Not all modems support the retrieval of the SIM ID. In particular, the Novatel Merlin UMTS modems and the Option Globetrotter modems do not support SIM ID retrieval. If the main menu shows an error status, at least partial modem information may be available.
Chapter 5: Settings SMS Menu When the PDA enters suspend mode, the modem remains powered. If the iKôn PDA is not turned on again during the configured time, the unit briefly wakes up from suspend mode, shuts down the modem, and enters suspend mode again. The default mode is Enabled Keep on for 1 hour. At the cost of a slightly increased power consumption in suspend mode, the modes where the modem remains powered during suspend mode have several advantages.
Chapter 5: Settings SMS Menu 5.36.6.1 New SMS Tapping on New opens a dialog box for sending a new SMS message. The recipient's phone number (to be entered in the To field) can consist of the digits 0 through 9, as well as the * and # characters, optionally preceded by one + character, indicating an international number (i.e. the country code follows immediately after the + character). By checking the Store message in Outbox field, a new message can be stored in the Outbox before being sent.
Chapter 5: Settings SMS Menu most recently received message first. The list can be sorted by any other column by clicking on the corresponding column heading. Clicking the same column heading twice reverses the sort order. Pressing any letter or digit moves the highlight to the next message whose address begins with that letter or number. Note: The date and time formats can be changed through the Regional Settings in the Control Panel.
Chapter 5: Settings SMS Menu 5.36.6.4 SMS Configuration Tapping on SMS Configuration opens the SMS configuration dialog. The SMS Centre Address follows the same rules as the recipient's phone number in the New message dialog.
6 PROGRAMS 6.1 Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 6.2 Games . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 6.3 ActiveSync® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 6.3.1 Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 6.4 Calculator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 6.5 Demo Scanner . . . . . .
6.11 Summit Client Utility (SCU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 6.12 Search . . . . . . . . . . . . . . . . . . . . . 6.12.1 Internet Explorer . . . . . . . . . . . 6.12.2 Browsing Web Sites . . . . . . . . . 6.13 Messaging . . . . . . . . . . . . . . . . . . . 6.13.1 Folders . . . . . . . . . . . . . . . . 6.13.2 Synchronizing E-mail With Outlook 6.13.3 Changing Synchronization Settings . 6.14 Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6: Programs Programs 6.1 Programs The Programs menu provides access to all the applications available on your iKôn PDA. • Tap on Start>Programs to display this screen. Tapping on an icon in this screen launches the associated applet. Figure 6.1 Programs Tabs 6.2 Games Your iKôn PDA is equipped with a few standard games–Bubble Breaker and Solitaire– should you feel the need to pass the time. 6.
Chapter 6: Programs Calculator 6.4 Calculator Tapping on Start>Programs>Calculator displays a standard calculator with regular functions. • 6.5 Use your stylus to tap the calculator buttons. Demo Scanner The Demo Scanner icon is used to test how the PDAPDA reads and writes bar codes. The Demo Scanner dialog box contains buttons at the bottom of the dialog box that allow you to Scan, Reset or change bar code Setting. 6.
Chapter 6: Programs Word Mobile 6.6.1.1 Workbook Components Columns Address of selected text Entry bar Cell Rows Status bar Toolbar Menu bar Selected cell Formula drop-down menu Sheet1 drop-down menu • If the toolbar is not visible, tap on the View>Toolbar. You can enter data, work with rows and columns and create formulas as you would when working with Excel on your PC. Using Excel Mobile Help If you need help using this application, you can review the instructions in the associated help files.
Chapter 6: Programs Word Mobile If you’ve already create a Word Mobile document, it will be listed in the Word Mobile window. • Tap on New in the softkey bar to create a new Word document. Using Word Mobile Help If you need help using this application, you can review the instructions in the associated help files. To display Word Mobile help files: • • Launch the Word Mobile program. Tap on Start>Help, and review the instructions provided. 6.6.2.
Chapter 6: Programs PowerPoint Mobile Important: To avoid translation problems, you can work on copies of .doc files. In addition, keep in mind that you can use the Terminal Services Client program to log onto a desktop PC that is also running Terminal Services, and then you can use any program on your PC, including Microsoft Word (rather than Word Mobile). Refer to “Remote Desktop Mobile” on page 238 for details. 6.6.
Chapter 6: Programs Using Internet Sharing You’ll need the following information before you begin: From your cellular service provider: data connectivity information, access point name and PAP/CHAP security settings. From your Internet service provider (ISP) or wireless service provider: access point name and password and any additional security information. For a GPRS, 1xRTT or dialup connection: • • • • • 6.8.2 Tap on Start>Settings>Connections tab. Tap on the Connections icon.
Chapter 6: Programs Notes • 6.9 If the iKôn PDA is listed as a Network Access Point, click Connect. If it is not listed, click Create a new connection and use the New Connection Wizard to add the iKôn PDA to the list. Notes The Notes application is an electronic notepad you can use to jot down your ideas quickly. You can enter text using the soft keyboard, the iKôn PDA keyboard, or you can write on the screen using your stylus. You can also record a message.
Chapter 6: Programs Converting Handwritten Notes To Text • Compose your note using the method you’ve chosen. • Tap on OK when you’re done. Your note is automatically saved. The file name is the first line of the note if you used the keyboard–otherwise, it’s named Note1, Note2 and so on. 6.9.2 Converting Handwritten Notes To Text When you use the pen tool, you can write notes in your own handwriting and keep them as is, if you like.
Chapter 6: Programs Converting Handwritten Notes To Text The text in the note is converted from handwritten to printed text. Note: To convert only a specific portion of your handwritten note into printed type, tap the stylus just before the first letter of the text, pause for a second, and then drag your stylus across the text you want to select. Then, tap on Tools>Recognize to convert only the highlighted text. Failed Conversions The Recognize tool sometimes gets the conversion wrong.
Chapter 6: Programs Renaming A Note • • • 6.9.3 Tap on the correct word in the list. If the correct word is not listed, as is the case in the sample screen above, tap on the soft keyboard icon to display the soft keyboard, and type the correct word. Renaming A Note • Press and hold the stylus on the file name in the Notes screen that you want to rename. In the pop-up menu, choose Rename/Move, or Tap the file name to select it, and tap on Menu>Rename/Move. • 6.9.
Chapter 6: Programs Synchronizing A Note A speaker icon is displayed in the note indicating the presence of a recording within the note. • 6.9.5 To play the recorded note, tap on the speaker icon. Synchronizing A Note Like Tasks, Contacts and so on, the Notes program can be synchronized with Outlook on your PC. In this way, all notes, recordings and drawings created in the Notes program are copied to your PC and can be edited in Outlook’s Notes module.
Chapter 6: Programs Opening A Photo • On your PC, using Windows Explorer (right-click My Computer and click on Explorer), drag photos from their folder to the Mobile Device, My Pictures folder. 6.10.2 Opening A Photo • Tap on Start>Programs>Pictures & Videos. You’ll see a thumbnail of your photos. Note: If you’ve stored your photos on a storage card, you’ll need to tap on the storage card icon to display your photos. • Tap on a thumbnail to open a photo. 6.10.
Chapter 6: Programs Summit Client Utility (SCU) The slide show begins–in slide show mode, photos are displayed for about five seconds, one after the other. • To display the slide show tool bar, tap anywhere on the photo. Pause Play Flip View 6.11 Previous Next Close Summit Client Utility (SCU) The SCU provides the utilities you will need to configure the Summit 802.11b/g Compact Flash radio module so that it can communicate through a wireless LAN network effectively and securely. Refer to 2.7.
Chapter 6: Programs Search 6.12 Search • Tap Start>Programs, and then tap on the Search icon. • • In the Search for field, type the item for which you’re looking. To narrow your search, tap on the Type dropdown menu and choose from a list of preexisting programs. To search through all files, leave this option at All Data. 6.12.
Chapter 6: Programs Messaging • Tap on Start>Programs>Internet Explorer to open Internet Explorer. If Internet Explorer is also from the Today screen, tap on Start>Internet Explorer. • Tap on the address bar–the field near the top of the screen where URLs are entered–to highlight the current URL. • Type a new URL in the address bar. Tapping on the softkeys in the softkey bar at the bottom of the screen display Internet Explorer commands like those you find on your PC. 6.
Chapter 6: Programs Synchronizing E-mail With Outlook Inbox folder and delete them from the server, preventing duplication of messages. Keep in mind however that you will not have further access to messages that you moved to folders from anywhere except with the PDA. For IMAP4 accounts, the folders you create and the messages you move are reflected on the server, making messages available any time whether you connect to your mail server from your iKôn PDA or your PC. 6.13.
Chapter 6: Programs Changing Synchronization Settings 6.13.3 Changing Synchronization Settings • In ActiveSync on your PC, double-tap the E-mail item in the Sync Options tab. • Tap on the Select Folder button. • Add a checkmark next to the folders in this screen that you want to synchronize with your iKôn PDA, and tap on OK. The E-mail Synchronization screen is displayed again. • • If you want to accept file attachments, add a check mark next to Include file attachments.
Chapter 6: Programs Tasks 6.14 Tasks This program helps you stay ahead of your schedule by managing your tasks, appointments, and so on. For details about Tasks, refer to “Task Notification” on page 57. 6.15 Remote Desktop Mobile This program allows you to log onto a Windows Terminal Server and run the desktop programs from the server on your iKôn PDA. 6.15.
Chapter 6: Programs Windows Update 6.17 Windows Update This program checks for software updates, and if found, downloads updates to your iKôn PDA. You can choose to have updates checked automatically, or if you prefer, you can determine when your unit will check for updates.
8 SPECIFICATIONS 8.1 iKôn PDA Specifications (Model No. 7505). . . . . . . . . . . 8.1.1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . 8.1.2 Software . . . . . . . . . . . . . . . . . . . . . . . . 8.1.3 Wireless Communication. . . . . . . . . . . . . . . . 8.1.4 Bar Code Applications (optional) . . . . . . . . . . . 8.1.5 RFID Modules . . . . . . . . . . . . . . . . . . . . . 8.1.6 Accessories . . . . . . . . . . . . . . . . . . . . . . . 8.1.7 Approvals. . . . . . . . . . . . . . . . . . . . .
Chapter 8: Specifications iKôn PDA Specifications (Model No. 7505) 8.1 iKôn PDA Specifications (Model No. 7505) Note: Performance specifications are nominal and subject to change without notice. 8.1.1 Hardware Physical Dimensions • 15.5 cm x 8.0 cm x 4.0 cm (6.1 in. x 3.15 in. x 1.57 in.). Weight (with battery pack) • 350 g (0.77 lbs.). User Interface Color Touchscreen Display: 9.39 cm (3.7 in.
Chapter 8: Specifications Software Wireless headset via Bluetooth capability Audio jack (mono) Expansion Slots • • • One Micro-SD memory card slot – user accessible. 60-PIN expansion interface: GSM/GPRS EDGE, and other third-party expansion modules developed using Psion Teklogix iKôn PDA Hardware Developer’s Kit. Flex cable interface with robust connector: supports scanner (serial) and imager (USB) modules.
Chapter 8: Specifications Wireless Communication • 128 MB flash, 128 MB RAM Operating System • • Microsoft® Windows® Mobile® 6 Classic Microsoft® Windows® Mobile® 6 Professional Programming Environment • • • • • Psion Teklogix Mobile Devices SDK Hardware Development Kit (HDK) .NET and C++ programming using Microsoft® Visual Studio® 2005 Java programming supporting JDK 1.2.2 or higher Standard Protocol APIs - Windows sockets (CE .net) Application Software • • • • • • 8.1.
Chapter 8: Specifications Bar Code Applications (optional) - Quad-Band – 850/900/1800/1900 MHz - Voice and Data - GPRS Class B, Multi-Slot Class 12 - EGPRS Class B, Multi-Slot Class 12 UMTS (Applies to Model 7505-BTHC25 & 7505-BTSDCMHC25) - UMTS/HSDPA: Triple band, 850//1900/2100 MHz GSM/GPRS/EDGE: Quad band, 850/900/1800/1900 MHz Note:- All are user upgradeable. - Audio: 1 analog interface - USB supports a USB 2.
Chapter 8: Specifications Accessories • 8.1.6 Accessories Power • • • • AC power supply (charge & operate PDA) Automotive power supply (charge & operate hand-held) Single slot battery pack chargers Powered cradle for vehicle-mount applications Communications • • • Quad Dock (4-site) with 10/100 BaseT Ethernet and charge functions Desktop Docking Station (charges PDA & spare battery) provides USB1.
Chapter 8: Specifications Radio Specifications FDA 21 CFR 1040.10 1040.11 Class II Bluetooth: 1.2 RF: Bluetooth and 802.11b/g: EN300 328, Part 15.247 GSM/GPRS: EN301 511; EN50360/361, NAPRD03; 3GPP51.010; FCC Parts 22 & 24; Industry Canada; RSS-132 & 133 In-Vehicle Cradle: e Mark 8.2 Radio Specifications 8.2.1 802.11 b/g WLAN Radio Form factor Compact Flash Type I extended Antenna port Two Hirose U.
Chapter 8: Specifications Siemens MC75 GSM/GPRS/EDGE Radio GPRS multi-slot class 12 GSM release 99 Output power: - Class 4 (2 W) for EGSM850 - Class 4 (2 W) for EGSM900 - Class 1 (1 W) for GSM1800 - Class 1 (1 W) for GSM1900 Control via AT commands (Hayes 3GPP TS 27.007 and 27.005) Internet Services: TCP, UDP, HTTP, FTP, SMTP, POP3 Supply voltage range: 3.2 to 4.3 V Specifications for: EDGE data transmission: EDGE class 12: max 236.
Chapter 8: Specifications Siemens HC25 UMTS Modem Interfaces: Hirose U.FL-R-SMT 50 ohm antenna connector Antenna solder pad Molex 80-pin board-to-board connector - Power supply - Audio: 2x analog, 1x digital - serial interface (ITU-T V.24 protocol) - SIM card interface 3 V, 1.8 V 8.2.
Chapter 8: Specifications Siemens HC25 UMTS Modem kbps UL CS data rate – 64 kbps DL / 64 kbps UL GSM / GPRS / EGPRS features: Data transfer GPRS - Multislot Class 10 - Full PBCCH support - Mobile Station Class B - Coding Scheme 1 – 4 EGPRS - Multislot Class 10 - EDGE E2 power class for 8 PSK - Downlink coding schemes – CS 1-4, MCS 1-9 - Uplink coding schemes – CS 1-4, MCS 1-9 -Uplink coding schemes – CS 1-4, MCS 1-9 - BEP reporting - SRB loopback and test mode B - 8-bit, 11-bit RACH - PBCCH support - 1 ph
Chapter 8: Specifications Bluetooth Radio Windows Mobile™ Interfaces: 8.2.4 USB Supports a USB 2.0 Full Speed (12Mbit/s) device interface Audio: 1 analog interface UICC interface: Supported chip cards: SIM / UICC 3V, 1.8V Antenna 50Ohms. External antenna can be connected via antenna connector or antenna pad (spring contact) Module interface 50-pin board-to-board connector Bluetooth Radio Embedded (920 kbps serial interface) Bluetooth Version 1.
Chapter 8: Specifications Electro-Chemical Description Description Specification Cell Configuration 2P1S (2 parallel connected cells) Cell Type Cylindrical Maximum discharge current 5.0A (1C) -20°C to +60°C (-4°F to +140°F) Charge algorithm Constant - current / constant voltage with taper current & timeout termination Maximum charge voltage 4.2V +/- 1% Maximum charge current 1C - dependant on cell manufacturer Discharge cutoff 2.
Chapter 8: Specifications Electrical Specifications 8.3.2 Electrical Specifications Description Specification Communication interface Smart Management Bus (SMB) Internal Battery Data Dependent upon cell parameters. Vendor to calculate and provide data. Charge control CV 4.2V, CC5.0A- dependant on cell manufacturer, Pre-charge 100mA, Current taper 100 - 250mA Fuel gauge Texas Instruments BQ27350PW Accuracy: +/- 1% of remaining battery capacity Resolution: 10 steps minimum 8.3.
Chapter 8: Specifications Scanner/Imager Model Numbers Description Specification Drop Rate IEC 60068-2-32 Drop sample battery on all faces from height of 1.2 meters onto conTest Ed: Free fall crete floor. No explosion, fire, vent, leakage and the open circuit voltage higher than 3.7V.
Chapter 8: Specifications Scanner Specifications 8.5 Scanner Specifications 8.5.1 SE 955HP Specifications Scan Engine SE 955HP Scan Angle 47° ± 3° default / 35° ± 3° reduced Scan Rate 104 (± 12) scans/sec (bi-directional) Scan Pattern Linear Wavelength 650nm Input Voltage 3.0-5.5 VDC ± 10% Input Current 65 mA typical Standby Current 8 µA max Operating Temperature -20° to 60° C -4° to 140° F Print Contrast Minimum 25% absolute dark/light reflectance measured at 650 nm Dimensions 1.
Chapter 8: Specifications EV15 Imager Specifications 20 mil 1.75 in. - 35.5 in. / 4.45 cm - 90.17 cm 40 mil * - 40 in. / * - 101.6 cm 55 mil * - 55 in. / * - 139.7 cm * dependent on width of bar code 8.5.2 EV15 Imager Specifications Parameter EV15 Light Source 617nm Highly Visible LED Scan Angle 40º Minimum Print Contrast Minimum 25% Min x. Dimension 0.
Chapter 8: Specifications SX5400 Imager 40 3 35.5 High quality symbols in normal room light. 8.5.3 SX5400 Imager Specification 284 SX5400 Optical resolution 752H x 480V Field of view at 160mm 120mm (H) x 78mm (V) 41.1° (H) x 27.
Chapter 8: Specifications SX5400 Imager Relative humidity 5% to 95% (non-condensing) Weight Image engine 4.1 grams Co-processor board 6.80 grams Shock 15 drops, 5 ft to concrete at room temperature when integrated correctly into end-user packaging 8.5.3.1 SX5400 Near, Far & Depth Of Reading* Size (mil) Symbology Near Avg. (Inches) Far Avg. (Inches) DOR Avg. (Inches C39 7.5 4.0 7.0 3.0 C39 10 2.75 9.25 6.5 C39 15 2.25 11.0 8.75 PDF6.6 6.6 4.0 6.5 2.5 PDF10 10 3.25 9.0 5.
APPENDIX A SUMMIT CLIENT UTILITY (SCU) For quick setup instructions for the 802.11b/g Summit radio using the Summit Client Utility, refer to “Setting Up A 802.11b/g Radio–Summit Client Utility” on page 15. A.1 SCU Tabs This section provides a detailed description of each of the tabs available in the SCU – Main, Config, Status, Diags and Global Settings. A.2 Main Tab The Main tab is displayed when you tap on the Start>Programs>SCU icon. • • Enable/Disable Radio: Enables or disables the radio.
Appendix A: Summit Client Utility (SCU) Config Tab • • • A.3 If ThirdPartyConfig is selected, after the iKôn PDA goes through a power cycle, WZC is used for configuration of the radio. See “ThirdPartyConfig” on page A-6 for details. Association Status: Indicates if the radio is associated to an access point. If this is not the case, Association Status indicates the radio status. Software Version: This field displays the version of the device driver and the SCU that are running on the iKôn PDA.
Appendix A: Summit Client Utility (SCU) Config Tab The following table describes the options in the Radio Attributes dropdown menu: Radio Attributes Description Value Default Config Name of config (configuration profile). Use Rename button to change name. Maximum of 32 characters. None SSID Service set identifier (SSID) for WLAN to which the radio connects. Maximum of 32 characters. None Client Name Name assigned to radio & iKôn PDA into which it is installed. Maximum of 16 characters.
Appendix A: Summit Client Utility (SCU) SCU Security Capabilities • A.3.1 User: Username or Domain/Username (up to 64 characters). Password: up to 64 characters. For PEAP: CA Cert–CA server certificate filename. None Credentials Authentication credentials for the selected EAP type. Refer to “EAP Credentials” on page A-5. Encryption None Type of encryption used to protect Off, Manual WEP, Auto WEP transmitted data.
Appendix A: Summit Client Utility (SCU) EAP Credentials • • • • EAP-MSCHAPV2, resulting in PEAP-MSCHAP: This is appropriate for use against Windows Active Directory and domains. EAP-GTC, resulting in PEAP-GTC: This is for authentication with one-time passwords (OTPs) against OTP data bases such as SecureID. LEAP: Is an authentication method for use with Cisco WLAN access points. LEAP does not require the use of server or client certificates.
Appendix A: Summit Client Utility (SCU) ThirdPartyConfig • • • • When prompted, you can enter valid credentials, enter invalid credentials, or cancel the operation. If you enter valid credentials and tap OK, the radio will associate and authenticate. If you enter invalid credentials and tap on OK, the radio will associate but will not authenticate; you will be prompted again to enter credentials.
Appendix A: Summit Client Utility (SCU) Global Settings Tab A.4 Global Settings Tab The Global Settings tab allows you to define radio and security settings that apply to all configs (profiles), along with settings that apply specifically to the SCU. The Global Settings in the table below can be edited in the SCU: Global Setting Description Value Default CCX features Activates three CCX features: AP-assisted roaming, AP-specified maximum transmit power & radio management.
Appendix A: Summit Client Utility (SCU) Global Settings Tab A-8 Preamble Type of radio preamble or headers. Auto, Short, Long Ping Payload Amount of data to be transmitted Bytes: 32, 64, 128, 256, on a ping. 512 & 1024 Auto 32 Ping Timeout ms Amount of time in milliseconds Integer from 0 to 30000. that passes without a response before ping request is considered a failure. 5000 Ping Delays ms Amount of time in milliseconds between successive ping requests. Integer from 0 to 7200000.
Appendix A: Summit Client Utility (SCU) Status Tab A.5 TX Diversity Defines how to handle antenna diversity when transmitting data to AP. -Main only: Use main antenna only. -Aux only: Use auxiliary antenna only. -On: Use diversity. On WMM Use Wi-Fi Multimedia Extensions, also know as WMM.
Appendix A: Summit Client Utility (SCU) Diags Tab A.6 Diags Tab Ping Address Ping Results Use the Diags tab as a troubleshooting tool. The functions are as follows: • • • • A-10 (Re)Connect: Enables/Disables the radio, applies/reapplies current config and tries to associate and authenticate to the wireless LAN, logging all activity in the output area at bottom of the dialog box. Release/Renew: Obtains a new IP address through DHCP and logs all activity in the output area.
APPENDIX B PORT PINOUTS B.
Appendix B: Port Pinouts Desktop Dock Spare Battery Charger Connector Pinout B.2 Desktop Dock Spare Battery Charger Connector Pinout Pin # 1 Signal Name POS Positive lead of battery - B.
INDEX A About, Bluetooth 187 About Device icon 108 About icon (software version) 108 Accepted Start Char 150 accessories carrying case 244 desktop docking station 247 Ethernet adaptor cable 251 hand strap 243 holster, soft shell 244 port replicator 261 quad docking station 255 single battery charger 253 vehicle cradle 257 Active Connections, Bluetooth 187 ActiveSync 14, 221 setting up 221 ActiveSync, CD installation 12 Adaptive Windowing 165 adaptor cable USB-Ethernet 251 Addendum 154, 166, 167, 168 Addend
Index Battery info.
Index communication ActiveSync 14, 221 data transfer 14 Ethernet connection (desktop dock) 251 Ethernet connection (quad dock) 255 PDA to PC 13, 250 Vista 14 COM port, Bluetooth 185 Composite 146, 169 connecting to a server with 238 Connections 180 editing settings 197 Internet 189 managing 197 modem setup 190 network, selecting 199 network cards, setting up 195 Proxy Server setup 200 VPN, setting up 196 connections managing 196 connectivity hotkey 53 Constant Illumination 166 Continuous Scan Mode 132, 148
Index F Factory Defaults On Reboot 164 Fast Converge (Imager) 165 features, PDA 4 feedback, customer (Microsoft) 114 Field Size 137 Field Size/Chars (bar code scanning) 137 file, renaming 65 File Explorer 64, 225 copy 65 copying a file 65 deleting file 66 folders, creating 65 renaming file 65 files & folders, managing 64 find (search) 234 flight mode (disabling the WLAN connection) 194 FNC1 Conversion 151 folder, copying 65 folder, creating 65 folder, deleting 66 folder, renaming 65 Full Ascii 149 Full AS
Index one shot mode 87 punctuation, accessing 37 Scancode Remapping 91 shift-state indicator icon 36, 37, 68 Unicode Mapping 90 keypad (phone) 18 L Laser On Time 131, 148 LED functions 42 Length Mode 156, 158, 159 Letter Recognizer 75 Letter Recognizer options (Input Methods tab) 97 Linear Decode 141 Linear Security Level 132 linking hand-held to PC 13, 14 Lock Sequence 94 Low Power Timeout 132, 149 L1, Set Length 135 L2, Set Length 135 M Macro keys 38 deleting a macro 89 executing a macro 89 Macros me
Index Outlook, CD installation 12 Outlook email, synchronizing (Messaging) 236 Owner Information 103 ownership information, defining 56 P pairing Bluetooth devices 184 Parameter Scanning 132, 149, 150, 151, 152, 155, 157, 158, 159, 160 PC, connecting PDA to 250 PC, linking to PDA 13 PDA specifications 269 PDF-417 146, 161, 169 phone keypad 18 phone keys (on the PDA keyboard) 23 using (Windows Mobile 6 Professional) 18 picker cradle installing cable 258 Pictures deleting 232 editing 232 opening 232 slide
Index Scancode remapping 91 Scan Data Format 134 Scan Indicator 173 Scan Log File 173 scanner one dimensional (1D) internal scanner 263 safety warnings 261 techniques (scanning) 262 troubleshooting tips 262 two dimensional (2D) imager scanner 263 scanner model numbers 281 scanner module (SE 955) specs 282 scanner options 261 scanning aiming (target) dot duration 131 appending characters 139, 172 Bad Scan Beep 173 bar code settings 129 check digit 143 Check Digits (MSI Plessey) 143 Check Digit Verification
Index UPC-EAN Shared Settings 154 UPC-E Check Digit 140 UPC-E Preamble 140 UPC-E1 Check Digit 140 UPC-E1 Preamble 140 1D internal 263 2D Maxicode 170 2D QR Code 169 2D UPC Half Block Stitching 142 Scanning Mode (2D) 133 Scan Result 173 Scan Result Time 173 screen navigating 51 stylus 51 touch pen 51 scrolling, adjusting speed (Up_Down tab) 86 SCU (Summit Client Utility) 15 Config Tab A-2 configuring 15 Diags (Diagnostics) Tab A-10 EAP Credentials A-5 EAP Types A-4, A-5 Global Settings Tab A-7 IP, assigning
Index 238 session, disconnecting (without ending) 238 session, ending 238 Text Block Recognizer 74 entering 71 Letter Recognizer 75 soft keyboard entry 72 transcriber, using 72 title bar (navigation bar) 52 Today’s Screen (desktop screen) 51 appearance of 106 Items (to appear in screen) 107 Total Recall 176 backup profile, creating 177 backup profile, restoring 180 touch pen, using 51 touchscreen calibrating 40 stylus, using 51 touch pen, using 51 touchscreen, aligning (calibrating) 40 Transcriber Inking 9