User Manual and Installation Guide Mobile Reader Edge www.proxy.com | support@proxy.
Contacts For additional offices around the world , see https://www.proxy.com/contact Proxy,Inc. San Francisco (Global Headquarters) 500 3rd Street #245 San Francisco, CA 94107 USA Proxy Technical Support: https://support.proxy.com/hc/en-us | 2 User Manual and Installation Guide: Proxy Mobile Reader Edge This document may have been updated since printing — for the latest, please visit https://proxy.
Table of Contents Introduction 5 Edge Reader Functionality 5 5 Edge Reader Enclosure 6 Edge Reader Enclosure Wall Plate 6 Edge Relay Enclosure 7 Edge Relay Enclosure Wall Plate 7 Product Details RF Exposure Information 8 8 Product Specifications 9 Installation Details Parts List 9 9 Recommended Tools 9 Wire connecters (dry/wet) 9 Recommended Infrastructure 10 Wiring Harness Information Cable colors for Edge Reader Enclosure [5 Core Grey] 10 10 Cable colors for Edge Relay Enclosure
| 4 User Manual and Installation Guide: Proxy Mobile Reader Edge This document may have been updated since printing — for the latest, please visit https://proxy.
Introduction This document details the Proxy Mobile Reader Edge and its basic operational and installation procedures. It covers the details of the Proxy Mobile Reader Edge form-factor. Model(s): ● Proxy Mobile Reader Edge White [Reader PEMW, Relay PERW] ● Proxy Mobile Reader Edge Black [Reader PEMK, Relay PERK] Version(s): ● 1.0, 1.1, 1.2, 1.
Edge Reader Enclosure Edge Reader Enclosure Wall Plate Dimension in millimeters (mm) & inches (in) | 6 User Manual and Installation Guide: Proxy Mobile Reader Edge This document may have been updated since printing — for the latest, please visit https://proxy.
Edge Relay Enclosure Edge Relay Enclosure Wall Plate Dimensions in millimeters (mm) & inches (in) | 7 User Manual and Installation Guide: Proxy Mobile Reader Edge This document may have been updated since printing — for the latest, please visit https://proxy.
Product Specifications Model Name: Mobile Reader Edge Device Type: Mobile Credential: Bluetooth Low Energy (BLE) Physical Access Control Reader (accessory equipment) Type of Equipment: Sealed Edge Reader (Suitable for Indoor and Outdoor use) Unsealed Edge Relay (Suitable for Indoor use only) Interface Type: Pigtail Cable Edge Reader Enclosure [5 Core Grey] Pigtail Edge Relay Enclosure [5 Core Grey, 8 Core Black] Input Voltage (v1.0, v1.1): Input Voltage (v1.
Installation Details Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction.
Recommended Infrastructure ● All cabling and wiring shall be UL Listed and/or UL Recognized ● Refer to Wiring Recommendations for guidance on wire type and length ● Power Supply- Sufficient to provide 500mA @ 12V DC plus power for door hardware. See door hardware manufacturer's specifications.
Cable colors for Edge Relay Enclosure [8 Core Black] Name Colors Colors Sheath Color Notes +VDC Red GND Black Strike COM Green Strike N/O White Rex + Brown Rex - Blue DPS + Grey v1.1 and above DPS - Grey v1.1 and above ** For Wiring diagrams and termination points please see the full installation manual available on our website. Installations will differ between electronic strike manufacturers and applications. ** All wires not being used should be terminated.
Wiring Recommendations Note: Always refer to vendor wiring instructions, requirements and recommendations for power supplies and access control system panels. Where vendors recommended installation requirements exist, they shall supercede the table below.
Mounting the Edge Reader Location of mounting holes on wall | 13 User Manual and Installation Guide: Proxy Mobile Reader Edge This document may have been updated since printing — for the latest, please visit https://proxy.
Edge Reader Installation Steps Important: Edge Reader and Edge Relay can NOT be installed at a distance greater than 30 ft (10 m) from each other ● Make two holes on the wall as per the image above corresponding to the type of reader o Edge Reader enclosure on the unsecured side (outside of the door frame) o Edge Relay enclosure on the secured side (inside of the door frame) ● Insert the nylon screw plugs into the wall ● Connect the wires as per Wiring Harness Information o ● Cables with the grey
Wiring Diagrams and Steps Connect to Door Hardware | 15 Step 1: Connect the 5 wires from the Edge Reader Enclosure (outside) unit to the 5 wires from the Edge Relay Enclosure (inside) unit based on corresponding colors Step 2: Crimp the positive (red) wire from the power source to the red wire of the Edge Relay Enclosure (inside) unit and to one of the wires from the strike Step 3: Crimp the ground (black) wire from the power source to the black wire of the Edge Relay Enclosure (inside) unit and to t
Connect to Controller Step 1: Connect the 5 wires from the Edge Reader Enclosure (outside) unit to the 5 wires from the Edge Relay Enclosure (inside) unit based on corresponding colors Step 2: Connect the brown and blue wires of the Edge Relay Enclosure (inside) unit to the two wires from the REX input of the access controller Step 3: Connect the black (GND) and red (+VDC) wires to a power source (this could be provided by the controller) equivalent to what is needed to power the electrified lock Doo
Power up and Testing 1. Turn power on ● Indicator light (top of enclosure) turns on and blinks red ● Branding light (front of enclosure) turns on (Proxy Logo Displayed) 2. Have an organization administrator refer to the Proxy Quick Start Guide, located at https://support.proxy.com for setting up their organization’s mobile access including how to download the mobile app and add new readers.
Average Power (dBm) Band / Mode LE GFSK Bluetooth 5 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
IC This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Please find below the Maximum Transmit Power for production units: Average Power (dBm) Band / Mode LE GFSK Bluetooth Band / Channel / Frequency (MHz) 2.4GHz WLAN 1.5 IEEE 802.11 Average Power (dBm) 11b 11g HT20 17.3 16.9 16.9 Average Power (dBm) Band / Mode LE GFSK Bluetooth 1.3 Hereby, Proxy, Inc., declares that the radio equipment type Proxy Mobile Reader Edge is in compliance with Directive 2014/53/EU. Please scan the barcode on the label to view the user guide.
UL294 All terminals are Power Limited / Class 2 circuits. UL294 access control performance levels ● Destructive attack: Level I ● Line Security: Level I ● Endurance: Level I ● Standby Power: Level I Install Troubleshooting Possible Symptoms Likely issue How to resolve Reader Logo is not illuminated Reader is constantly rebooting (turns on, beeps, turns off) Either wiring at the reader or at the power supply has been disconnected.
Logo is still purple after giving plenty of time for update Indicator flashing red continuously Update issue Try resetting the reader in the Proxy App. If this does not work, try manually resetting the reader by disconnecting and reconnecting the black and red wires. If this does not resolve the issue please email support@proxy.com to escalate. Hardware issue Power-cycling the Reader will likely resolve this issue. Contact support@proxy.com if it does not, or if this happens with any frequency.