PW-MN427_34I 150Mbps Wireless N USB Module
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may c ause ha rmful interference t o r adio c ommunications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Chapter 1 Introduction 1.1 Product Overview Thank you for choosing the PW-MN427_34I 150Mbps Wireless N USB Module. The Module is designed to provide a high-speed and unrivaled wireless performance for your computer. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, video streaming and so on. The PW-MN427_34I 150Mbps Wireless N USB Module complies with IEEE 802.11n, IEEE 802.11g and IEEE 802.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Chapter 2 Installation Guide 2.1 Hardware Installation PW-MN427_34I has USB interface(4-PIN connector,2.0mm pitch), and it is mainly d esigned to provide stability wireless function and performance for your system. For installation, you must be sure to connect this module to your device or system with a connecting wire first. Then, the promoted Found New Hardware Wizard will pop up if the Module is installed correctly. 2.2 Software Installation 2.2.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Figure 2-1 Start The Installation 2. Choose Update Driver Software, You’ll see the screen as below. You should choose the second item and click Browse my computer for driver software.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide 3. In the following screen, browse for driver software on your computer. Choose the destination location and click Next. Figure2-3 Browse For Driver 4. You will see the next screen as below, installing will appear.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide 5. Wait for a moment , and you will see Windows has successfully update your driver software. Figure2‐5 Driver Is Installed 6. After you installing the driver，please restart your computer then the hardware you installed will work, go to the Device Manager and check that 802.11n USB Wireless LAN Card is successfully installed as below.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide 2.3 Uninstall Software 2.3.1 Uninstall the driver software from your PC 1. On the Windows taskbar, click the Start button, and then click Control Panel. 2. Click the System icon, click on the Hardware tab in the System window. 3. Click on the Device Manager button, double-click Network Modules, and then right-click 802.11 n Wireless LAN Card. F i g u r e 2 9 D e v i c e M a n a g e Figure2-7 Uninstall Driver Software 4.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Chapter 3 Example for Application 3.1 Configuration of PSP XLink Online game Please ensure the software and hardware environments are well established before configuring. For hardware, at least a PC, a PW-MN427_34I 150Mbps Wireless N USB Module and a PSP device are needed. For software, the PW-MN427_34I Module driver should be properly installed. Please operate as follows: Step 1. Connect the website of X-LINK http://www.teamxlink.co.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Step 5. Right-click “My Computer” and select Management. In the prompt page, click Device Manager, then right-click “Wireless N Client Module “and select Properties. Then set the value of “PSP Xlink Mode” as Enable following the red marked instruction in the figure. Figure 3-2 Step 6. Click Start > Control Panel > Network. Figure 3-3 Step 7. Right-click Wireless Network Connection icon , and select Properties.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Figure 3-4 Step 8. In the prompt page shown below, select Use the Following IP Address, and set the IP and Subnet mask. After completing setting, click OK. Figure 3-5 Note: Please set the IP address in different network segment with the other network card to avoid conflict. Step 9. Launch RL52 Wireless N Client Utility, then highlight the Network Name (SSID) beginning with “PSP” in the “Network” page, and click Connect. Step 10.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Figure 3-6 Step 11. Click the icon on the right top corner to enter the Arena Mode, highlight the arena of your wanted game, and then join or start a new game.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide 3.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Appendix A: Glossary 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence sp read-spectrum (DSSS) technology a nd operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit shared key algorithm, as described in the IEEE 802.11 standard. Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices.
PW-MN427_34I 150Mbps Wireless N USB Module User Guide Appendix B: Specifications General Interface USB 2.0 (4-PIN connector,2.0 pitch) Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Operating System Windows XP/ Vista/ 7 ,Linux OS, Android Safety & Emission FCC, CE Frequency 2.4-2.
