USER MANUAL Solar Power Generator EB150P
Safety Instruction CAUTION! BEFORE USING YOUR ECOBOXX FOR THE FIRST TIME, GIVE IT A FULLY CHARGE. PLEASE CHARGE ECOBOXX EVERY THREE MONTHS TO KEEP THE BATTERY HEALTH. DO NOT alter or remove the factory plates and identification labels. DO NOT disassemble the device. Do not place the unit close to or in a fire or expose it to heat. Do not use or store the unit in a bathroom or in an area expose to rain or moisture. Do not connect the output to mains power under any circumstances.
If rust, odors, overheating or other abnormal circumstances are observed, stop using the unit immediately and contact the dealer The unit complies with all legal requirements for transport of dangerous goods Make sure the unit is properly secured wen transporting it in a motor vehicle Only charge, use and store the unit within the temperature of 0 to 40 degree C.
Warranty Warranty period is 12 months and measured starting on the date of purchase by the original customer purchaser. Provista will repair or replace any Provista’s product falls to operate during the applicable warranty period due to defect in workmanship or material. If a valid claim is made during the applicable period. Provista will replace the product and assumes the remaining warranty of the original product or 90 days from the date of replacement, whichever is greater.
Overview EB150P is a solar power generator with various AC and DC power output, a powerful device to power up and charge both DC and AC devices, such as smart phones, tablets, small TV’s & fans. The featured function of solar energy harvesting further enhances the product to make use of green and clean energy without completely relying on the current power grid. EcoBoxx has overcurrent protection, under-voltage and over-voltage protection is fully implemented.
Control Panel 1. COB LED Button: When EB150P power on , press LED button to turn on LED light, press it again to switch between low LED and high LED. Keep pressing the buttion, LED light will flash. 2. Wireless Charging Button: Press to enable the wireless charging, press again to switch off. Green LED will be on when it is working properly. Red LED will be on when a charging problem. 3. LCD Display: It shows the battery voltage, Input/output power, and false alarm. 4.
6. TYPE-C port: Support 5~20V, 3A, with max 60W input; And, it also support 5V/9V/12V/15V/20V, 3A, with max 60W output (No reminder when over current/short circuit , plug in again with the right load, it will work properly.) 7.QC3.0 USB port. Support 5V/9V 3.0A output. (No reminder when over current/shortcircuit , plug in again with the right load, it will work properly.) 8/9. Standard USB port. Support 5V 2.4A output.
In the box Item Description Qty A Main Unit 1 AC Adapter 1 B C User manual 1 D Car Charger cable 1 *ABOVE PARTS AND ACCESSORIES PHOTOS AND LIST ONLY FOR REFERENCE AND THE FINAL PACKAGE IS SUBJECT TO CHANGE BY REGIONAL REQUIREMENT.
Technical Specifications Description Specification Solar input range 10V~27V Max input current 3A Max input power (5.5mm charging port) 40W Adaptor output 12V/3A Battery Capacity (Lithium battery) 11.1V,13.2Ah, 146.52Wh Standby current 2mA Min.battery charging voltage 5V Max.battery charging voltage 12.5V Low battery protection 9V Recover battery voltage 10V Orange USB port x 1 output 5V/9V/3.0A max. White USB port x 2 output 5V/2.4A max. Input: 5~20V, 3A/60W max.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
USER MANUAL www.provistahk.