User Manual of Pronto Intelligent Access Point This is the manual of outdoor CPE, which will approximate guide you how to set and apply the outdoor CPE, it provide a convenient graphical interface for network construction and maintenance person, as well as a user through a simple and accurate operation, and configuration management of the CPE.
1 s t Connection and Power Supply 1 s t ： P o r t C o n n e c t i o n a n d p ow e r s u p p l y Instruction of different port： P1 CPE Port Connection Please use a power supply of 12V DC adapter or 24V POE adapter, WAN / LAN port is the PoE Port. Pls make sure the CPE’s power supply is normal in reset process, or the CPE will be Pay Attention damaged and can’t reboot Reset: There are two ways to reset the CPE: 1.
P3 Pay Attention Connection diagram of CPE and PoE adapter Incorrect Connection or the use power adapter and PoE adapter not from our factory, the CPE will be damaged 2 n d Steps： Login 1）Connect the CPE with computer as P2 picture 2）Configure the PC’s local connection IP address as 192.168.188.X (X is number from 2 to 254), subnet mask is 255.255.255.0, follow P4 and P5 to finish.
P4 Setting of computer’s IP address P 5 Setting of computer’s IP address 3) Input 192.168.188.
P6 Login 4) After login, then P6 Device Status will be showed: P7: Device Status There are four operation mode showed on this page: Gateway mode, Repeater Mode, AP Mode and WISP Mode; 3rd：Quickly Configure CPE ① Gateway Mode: Click “Gateway Mode” under following picture and choose the right WAN access type, then input the right SSID,
Channel, key as like. P8 Gateway Mode ② WiFi Repeater and Station operation configuration A. Login the Web management page, click “ Repeater Mode”, then “Scran AP” P9 Repeater Mode B. Select the AP’s SSID want to bridge, take SR800-5.8G for example.
P10 Select AP Instruction If your computer can’t pop up this window, pls check your IE explorer and see whether it is blocked already. And if this CPE can’t scan any SSID, pls check if there are 5G wireless signal. C.
P11 Repeater Mode D. In Repeater Mode, the SSID is disable in default setting, it work as Station; Then if need SSID broadcast in this operation mode, just manual to change under Advanced Settings, So, click sure in this part to finish the repeater operation mode setting. P12 Notice E. After this step, can click the Device status to check the status of this CPE. And it will show CPE’s LAN Interface, WLAN status and Sigbal Strength.
P 13 Device Status F. Then if SSID should be broadcast under repeater mode, pls click “Advanced Settings” , then “5.8GHz Repeater” will pop up. If want to bridge another AP’s SSID, then can setup in this part and Aplly changes. P14 5.8G Repeater G. Click “5.8GHz Virtual AP”, will shwo SSID shut off, if need SSID broadcast, pls follow steps of 1,2,3,4,5,6 showed in following picture. This CPE will work under wireless repeater and broadcast SSID after apply changes.
P15 5.8GHz Virtual AP ③ AP Mode Plug and Play to transmit wireless signal for wireless end users form wired networking. In this part, user can mark the AP’s location and name for easy problem checking. Then can change SSID, Key, Channel as request. P16 AP Mode ④ WISP In this operation mode, user should confirm the WAN access type at first, then set the SSID, key, Channel as request.
P17 WIPS Mode ⑤ Advanced Settings: 1. System Status Click “ Advance Settings”, will show system status, such as firmware version, build time, System uptime... P18 System Status Click 5.8GHz Wireless Status, will show CPE’s WLAN Status, Signal Strength, SSID...
P19 5.8GHz Wireless Status If want to check LAN status, pls check following picture P20 LAN Status 2. Operation Mode: Set operation mode manually, choose the right operation mode, then apply changes. The function of this part will be same as Quick Setup step.
P21 Operation Mode 3. 5.8GHz Repeater: In this part, use can scan AP’s SSID, disable or enable CPE’s SSID, modify Channel, Country code, Key.. P22 5.
United States P23 5.8GHz Advanced Note: The frequency selection feature is disabled by firmware for devices marketed to the US. only channels 1-11 will be used in North America. Country code selection is disabled. 4. Network Setting LAN Interface Setup mainly showed as follow: P24 Network Setting 5.
(GMT+13)United States P25 Management 6. Upgrade Firmware Pls click Upgrade Firmware, then browse and choose the firmware should upgrade, then click upgrade to upgrade the firmware. P26 Firmware Upgrade After finish firmware upgrade, pls click Save/Reload Settings, then reset settings to default. After that, the firmware upgrade is finished. 7.
Tr o u b l e S h o o t i n g : F 1 The Failure phenomenon and solution Failure phenomenon SYS Indicator off Can’t land to CPE through Web page CPE can’t connect with AP （the status display unconnected） Can’t scan the wireless AP The connection of CPE and AP is success, but the computer can’t share internet How to Reset CPE Solution Pls make sure the PoE module connection is right.
Note: *. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
