Installation Instructions

SPM
SAM
8.6” (218 mm) 8.6” (218 mm)
SPM & SAM
User’s Manual
/ Mounting Template
Up to 80 lbs / 36 kg
Included Mounting Hardware
1. Mount (SPM or SAM) (x1)
2. M4 x 10, 15 & 25 mm bolts (x4)
3. M5 x 10, 15 & 25 mm bolts (x4)
4. M6 x 10, 15 & 25 mm bolts (x4)
5. M8 x 10, 15 & 25 mm bolts (x4)
6. Rectangular washers (x4)
7. Concrete anchors SPM (x4), SAM (x2)
8. Round washers SPM (x4), SAM (x2)
9. 5/16” lag bolts SPM (x4), SAM (x2)
10. Mounting template (x1)
11. Allen key (x2)
12. Wrench (x1)
You Will Need
A. Bubble level
B. Stud nder
C. Marker
D. Drill
E. 3/16” (wood) or 1/2” (concrete) drill bit
F. Hammer
G. Wrench
*SPM used in diagrams, steps also apply to SAM.
Center Bars
Upper
hBars
Lower
hBars
Arms
Wall plates
1.1a With a stud nder, nd the wall studs
where you want to mount your TV.
*Make sure you understand the
note above.
1.2a Mark the center of the stud. Using the
provided mounting template** mark the
4 holes (2 on SAM) where the wall plate
will be mounted. Make sure it’s
leveled.
1.1b Using the provided mounting
template** mark the 4 holes (2
on SAM) where the wall plate
will be mounted.
1.3a Drill a 3/16” hole on each mark.
Upper hBar
Lower hBar
Bolts go
on top
1.4a Mount the wall plate using the lag bolts and the round washers.
Do not overtighten.
1.5a Push the covers in place.
1a. Drywall Installation
1b. Concrete Installation
2. Fix hBars to TV 4. Conceal Cables
Tilting
Gently pull the top of your TV while
pushing the bottom to the desired
position up to 15˚. Do the opposite to
tilt up.
Panning
Gently move your TV from side to side
until is ush to the wall or completely
extended at 90˚
Horizontal Adjustment
Adjust the level of the TV by loosening
and re-tightening the upper and lower
nuts with an hex wrench.
1.2b Drill a 1/2” hole with the same
depth of the anchor on each
mark.
3.1 Hang hBars from appropriate
keyholes on center bar
depending on hBars spacing
and desired height. See chart.
We recomend one person holds the TV
while other makes sure bolts are in place.
400 only and 300 high
300 medium
300 low and 200 high
200 low
3.2 Fix lower hBar with allen bolts.
4.1 Run cables along arm channels.
Do not run power and signal cables
together, this may cause interference.
4.2 Push cable covers until you hear them click
in place.
3.3 Tighten upper and lower bolts. Do not over tighten.
Rectangular
Washer
1.3b Insert a concrete anchor in
each hole until it’s ush to the
wall. Use a hammer if
necessary.
1.4b Mount the wall plate using the lag bolts and the round
washers. Do not overtighten.
For more information, visit:
www.promounts.com
Promounts
TM
name, logo and model
numbers are property of Promounts.
© Promounts
®
AUM020 v1.3
Disclaimer
Promounts intends to make this manual accurate and complete, however, Promounts makes no claim that the informa-
tion contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The information contained in this document is subject to change
without notice or obligation of any kind. Promounts makes no representation of warranty, expressed or implied,
regarding the information contained herein. Promounts assumes no responsibility for accuracy, completeness or
suciency of the information contained in this document.
Warnings & Cautions
IT IS HIGHLY RECOMMENDED THAT THIS PRODUCT BE INSTALLED BY A PROFESSIONAL.
PLEASE REVIEW THIS INSTRUCTION MANUAL COMPLETELY BEFORE STARTING THE INSTALLATION PROCESS.
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
corresponding instruction.
WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can
support a weight factor ve times the total weight of the equipment. If not, reinforce the structure before starting the
installation.
WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
WARNING: The installer is responsible for verifying that the wall or ceiling to which the mount is anchored will safely
support the combined load of all attached components or other equipment.
WARNING: The weight of the display placed on the mount must not exceed the maximum load capacity of the mounts.
WARNING: Watch for pinch points. Do not put your ngers between movable parts.
WARNING: Make sure the mount and brackets are correctly oriented.
CAUTION: Check the unit for shipping damage before you begin the installation.
**SPM & SAM
mounting template
Cut along the dotted line and
detach from manual.
You can use masking tape
(one that won’t damage your
wall) to keep it in place.
Make sure it is leveled.
*Important
Due to SPM’s nature, the center of your TV will only be on the center of the wall plate when the mount is
fully extended; otherwise it will be oset to the right or left up to 8.6” (218 mm) when at to the wall.
SAM will fold back to the center when at to the wall (no oset).
1.5a Push the covers in place.
2.1 Center top hBar horizontally
and bolt to matching holes on
the back of your TV using M4,
M5, M6 or M8 bolts (x4) and
optional rectangular washers
(x4).
Do not overtighten.
2.2 Center bottom hBar
horizontally and bolt to
matching holes on the back of
your TV using M4, M5, M6 or
M8 bolts (x4) and optional
rectangular washers (x4).
Do not overtighten.
3. Hang TV from Arm
Adjust Tilt by tightening
or loosening these bolts,
on both sides.
Adjust arms by tightening or
loosening bolts on articulations.
Don’t remove bolts from
arms, TV may fall down and
somebody may get hurt.
-90˚ to 0˚ to 90˚
SPM Only
Horizontal Adjustment Nuts
Tilt Adjustment Bolts
15˚ to -3˚