Installation Instructions

SAL
SPL
8.6” (218 mm) 8.6” (218 mm)
SPL & SAL
User’s Manual
/ Mounting Template
Up to 120 lbs / 54 kg
Included Mounting Hardware
1. Mount (SPL or SAL) (x1)
2. M5 x 10, 15 & 25 mm bolts (x4)
3. M6 x 10, 15 & 25 mm bolts (x4)
4. M8 x 10, 15 & 25 mm bolts (x4)
5. Rectangular washers (x4)
6. Concrete anchors (x4)
7. Round washers (x4)
8. 5/16” lag bolts (x4)
9. Mounting template (x1)
10. Allen key (x2)
11. Wrench (x1)
You Will Need
A. Bubble level
B. Stud nder
C. Marker
D. Drill
E. 3/16” (wood) or 1/2” (concrete) drill bit
F. Hammer
G. Wrench
*SPL used in diagrams, steps also apply to SAL.
2.1a With a stud nder,
nd the wall studs
(2) where you want
to mount your TV.
2.2a Mark the center of the studs. Using the
provided mounting template** mark the
4 holes where the wall plate will be
mounted. Make sure it’s leveled.
2.3a Drill a 3/16” hole on each mark.
2.4a Mount the wall plate using the lag bolts and the round washers.
Do not overtighten.
2a. Drywall Installation1. Adjust Wall Plate Location
2b. Concrete Installation
3. Fix hBars to TV
Tilting
Gently pull the top of your TV while
pushing the bottom to the desired
position up to 15˚. Do the opposite to
tilt up.
Panning
Gently move your TV from side to side until is ush to the wall or completely
extended at 90˚
400 only and 300 high
300 medium
300 low and 200 high
200 low
Disclaimer
P
romounts intends to make this manual accurate and complete, however, Promounts makes no claim that the information contained
herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation
or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
Promounts makes no representation of warranty, expressed or implied, regarding the information contained herein. Promounts
assumes no responsibility for accuracy, completeness or suciency of the information contained in this document.
Warnings & Cautions
IT IS HIGHLY RECOMMENDED THAT THIS PRODUCT BE INSTALLED BY A PROFESSIONAL.
PLEASE REVIEW THIS INSTRUCTION MANUAL COMPLETELY BEFORE STARTING THE INSTALLATION PROCESS.
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding
instruction.
WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can support a weight
factor ve times the total weight of the equipment. If not, reinforce the structure before starting the installation.
WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
WARNING: The installer is responsible for verifying that the wall or ceiling to which the mount is anchored will safely support the
combined load of all attached components or other equipment.
WARNING: The weight of the display placed on the mount must not exceed the maximum load capacity of the mounts.
WARNING: Watch for pinch points. Do not put your ngers between movable parts.
WARNING: Make sure the mount and brackets are correctly oriented.
CAUTION: Check the unit for shipping damage before you begin the installation.
For more information, visit:
www.promounts.com
Promounts
TM
name, logo and model numbers are property of Promounts.
© Promounts
®
AUM022 v1.3
**SPL & SAL
mounting template
You can use masking tape
(one that won’t damage your
wall) to keep it in place.
Make sure it is leveled.
4. Hang TV from Arm
Center
Bars
Upper
hBars
Lower
hBars
Arms
Wall
plates
Wall
plate
rails
*Important Note
Due to SPL’s nature, the center of your TV will only be on the center of
the wall plate when the mount is fully extended; otherwise it will be
oset to the right or left up to 8.6” (218 mm) when at to the wall.
SAL will fold back to the center when at to the wall (no oset).
2.1b Using the provided mounting
template** mark the 4 holes where
the wall plate will be mounted.
Have a separation of no more than
17” (430 mm) between right and
left holes.
2.2b Drill a 1/2” hole with the same
depth of the anchor on each mark.
2.3b Insert a concrete anchor in each hole until it’s
ush to the wall. Use a hammer if necessary.
2.4b Mount the wall plate using the lag bolts and round washers.
Do not overtighten.
4.1 Hang hBars from appropriate
keyholes on center bar depending on
hBars spacing and desired height.
See chart.
We recomend one person holds the TV while
other makes sure bolts are in place.
Adjust arms by tightening or loosening bolts on
articulations. Don’t remove bolts from arms, TV may
fall down and somebody may get hurt.
Rectangular
washer
3.1 Center top hBar horizontally
and bolt to matching holes on
the back of your TV using M5,
M6 or M8 bolts (x4) and
optional rectangular washers
(x4).
Do not overtighten.
3.2 Center bottom hBar
horizontally and bolt to
matching holes on the back of
your TV using M5, M6 or M8
bolts (x4) and optional
rectangular washers (x4).
Do not overtighten.
4.2 Fix lower hBar with allen bolts (x2).
4.3 Tighten upper and lower bolts.
Do not over tighten.
Adjust tilt by tightening or
loosening these bolts, on
both sides.
Bolts go
on top
1.1 Loosen bolts and position the wall plate in the
desired sliding slots of wall plate rails. You may
have to remove the bolts (x4) and washers (x4).
Once you have bolted the rails to the wall, it will
be dicult to slide the wall plate sideways.
*Make sure you understand the important
note.
Upper hBar
Lower hBar
5. Conceal Cables Horizontal Adjustment
Adjust the level of the TV by
loosening and re-tightening
the upper and lower nuts with
an hex wrench.
4.1 Run cables along arm channels.
Do not run power and signal
cables together, this may
cause interference.
4.2 Push cable covers until you hear
them click in place.
-90˚ to 0˚ to 90˚
-3 to 15˚