SS-989 2 IN 1 SMD HOT AIR REWORK STATION 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.TestEquipmentDepot.com User’s Manual 1st Edition, 2012 ©2012 Copyright by Prokit’s Industries Co., Ltd.
SAFETY INSTRUCTIONS WARNING Warnings and cautions are placed at critical points in this manual to direct the operator's attention to significant items. They are defined as follows: WARNING: Failure to comply with a WARNING may result in serious injury or death. CAUTION: Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved. Two examples are given below. NOTE : A NOTE indicates a procedure or point that is important to the process being describe.
_ Do not disassemble the pump. _ Do not modify the unit. _ Use only genuine Pro’sKit replacement parts. _ Do not wet the unit or use the unit with wet hands. _ Remove power cord by holding the plug – not the wires. _ Make sure the work area is well ventilated. _The Pro’sKit SS-989 is not intended for use by children or infirm persons without supervision. _ Children should be supervised to ensure that they do not play with the SS-989. I. Packing list and name of parts Name of Parts Packing List 1. 1.
II. Features and Specifications Features: 2 in 1 Rework Station to save the cost Antistatic soldering iron and hot air desoldering 2 in 1 design to save the cost. Closed Circuit Sensor Design Closed-loop temperature control for accurate and air-flow-independent temperature High Power, Quick Warm Up Times High heating power, warm up quickly, adjustable temperature and air flow for easy surface or hole mount components QFP, SOP type IC devices rework.
Specification: Model SS-989B SS-989A SS-989A7 SS-989B4 SS-989C AC220V AC110V AC127V AC240V AC240V 50Hz 60Hz 60Hz 50Hz 50Hz Fuse 3A 250V 6A 250V 5A 250V 3A 250V 3A 250V Total power 700W Overall package size (mm) 330 (L) * 275 (W) * 195 (H) Weight 3.
C. Electrical Connection and Power ON ●Place the heat gun on the holder.(Fig3) Fig3 ●Loosen the pump securing screw which on the bottom of control station. (See below pictures) ●Insert the power plug into socket ●Turn on the power switch and the lamp will be lit ●Don‘t pull out the power plug instantly after turning off the power switch, because the fan keeps operating to protect heat element. Until the fan stops operation completely, the power plug should not be pulled out. III.
squeezing the wire. In case of PLCC or small components such as chip resistors, desolder by using tweezers, etc. 3. Hold the heat gun up on the SMD components, but do not touch the components, and allow the hot air to melt the solder. Be careful not to touch the leads of the components with nozzle. 4. When the soldering tin is melted, remove the SMD components by lifting the pick up puller (Fig. 5) Fig. 5 5. After removing SMD components, remove residual soldering solder tin with desoldering tool.
4. Cleaning When soldering is completed, clean the residual flux from the board with an appropriate cleaner. IV. Soldering iron operation instructions 1. Soldering iron stand assembly ● Install the cleaning sponge into the seat. (Fig. 8) Fig. 8 ***ATTENTION*** Sponge will swell when wet. Dampen the sponge with water and squeeze dry before using. The tips may be damaged when used with dry sponge. 2. Insert soldering iron into the stand. (Fig. 9) 3. Take out the protection tube on the top of soldering iron.
5. Insert power plug into power socket then turn on power switch. 6. Adjust temperature with regulation temperature knob. ***ATTENTION*** High temperature shortens tip life and may cause thermal shock to components. Always use the lowest possible temperature when soldering. It will also provide better protection for some components which sensitive to temperature. ***ATTENTION*** Always put soldering iron into holder after use.
apply fresh solder containing flux and clean the tip again. Repeat until all the oxide is removed then coat the tip with fresh solder. ◆ If the soldering iron tip gets deformed, replace it with a new one. V. Fuse replacement When fuse is blown, replace it with the spare fuse. (see below picture) 1. Unplug the power cord from the power receptacle 2. Use the Phillip (+) type screwdriver to loosen the fuse holder 3. Replace the fuse with new one 4.
Trouble shooting Warning: Before checking the inside of the SS-989 or replacing parts, be sure to disconnect the power plug. Failure to do so may result in electric shock.
