Ceiling Fan Installation Manual 93114642_A P250010
Limited Lifetime Warranty Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules..................................................................................................................................................................................... 1. Unpacking Your Fan ....................................................................................................................................................................... 2. Installing Your Fan .........................................................................................................
1. To reduce the risk of electric shock, ensure electricity has been turned off 10. Suitable for use with solid-state speed control. at the circuit breaker or fuse box before beginning. WARNING 2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3.
2 5 8 12 9 1 3 10 13 a b 6 4 7 11 14 c Unpack your fan and check the contents. You should have the following items: 1. 2. 3. 4. 5. 6. 7. Fan blades (4) Canopy assembly Ball/downrod assembly Coupling cover Fan motor assembly Mounting plate Set of blade brackets (4) 8. Decorative cover 9. Decorative nut 10. Receiver with 6 wire nuts 11. Transmitter incl. holder + 2 mounting screws 12. 12V battery 13. Balancing kit 14. Loose parts bag containing: a.
Tools Required Angled ceiling maximum 24 angle Phillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters. Provide strong support Mounting Options If there isn't an existing cUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials.
the hanger pin through the holes in the collar and downrod. Be careful not to jam the pin against the REMEMBER to turn off the power. Follow wiring inside the downrod. Insert the locking pin through the hole near the end of the hanger pin until it the steps below to hang your fan properly: snaps into its locked position, as noted in the circle Step 1. Remove the decorative canopy bottom inset of Fig. 7. cover from the canopy by turning the cover counter clockwise.(Fig.
Hanger bracket Safety cable Canopy Figure 8 Making the Electrical Connections 1. (Figure 10) Insert the receiver into the mounting bracket with the flat side of the receiver facing the ceiling. NOTE 2. (Figure 11) Motor to receiver electrical connections: Connect the black wire from the fan to black wire marked "TO MOTOR L". Connect the white wire from the fan to the white wire marked "TO MOTOR N" from the receiver.
Hanger bracket DO NOT USE WITH A WALL LIGHT DIMMER SWITCH. SUPPLY CIRCUIT BLACK WARNING CHECK TO SEE THAT ALL CONNECTIONS ARE TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS. EXCEPT FOR THE GROUND WIRE. Ground Conductor WHITE Receiver BLACK BLUE WHITE Figure 10 GREEN Outlet Box WHITE BLUE BLACK Remote Control BLACK WHITE CAUTION Green Ground Lead Ground to Downrod Receiver Figure 9 Figure 11 6.
Finishing the Installation Step 1. Tuck connections neatly into ceiling outlet box. Step 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 12) Step 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
Attaching the Fan Blades Blade Balancing Step 1. Attach the blades to the blade arms using three screws and fiber washers as shown in Figure 14. Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. All blades are grouped by weight. Because natural woods very in density, the fan may wobble even though the blades are weighed equally. Step 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight. Step 3.
CAUTION: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. Installing the battery Install a 12V battery (included) into the remote control. To prevent damage to the remote control, remove the battery if not used for long periods. (Fig. 17) Step 1. Remove the 1 of 3 screws from the posts of the mounting plate and keep it for future use.
Restore power to ceiling fan and test for proper operation. 1. " , , " buttons: These three buttons are used to set the fan speed as follows: = Low speed = Medium speed = High speed 2. The " " button turns the light ON or OFF and also controls the brightness setting. Press and release the button to turn the light ON or OFF. Press and hold the button to set the desired brightness. The light key has an auto-resume, it will stay at the same brightness as the last time it was turned off. 3.
Installing the Remote Control Holder Here are some suggestions to help you maintain your fan Attach the remote control holder with the remote control holder mounting screw. (Figure 21) 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Screw Figure 21 Remote Control Holder 2.
Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. 3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.
Fan Size 56" Speed Volts Amps Watts RPM CFM N.W. G.W. C.F. Low 120 0.23 12.02 56 2250.56 120 0.56 66.8 148 6255.84 22.11 lbs 1.89' High 20.06 lbs These are approximate measures. They do not include Amps and Wattage used by the light kit. c 2019 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 All Rights Reserved 13.
Manuel d'installation du ventilateur de plafond 93114642_A P250010
Garantie à vie limitée Progress Lighting garantit à l’acheteur initial que les moteurs de ventilateur sont exempts de défauts électriques ou mécaniques tant que l’acheteur initial est propriétaire du ventilateur. Les interrupteurs à chaînette, les interrupteurs inverseurs, les condensateurs et les finis métalliques sont garantis contre les défauts de matériaux ou de fabrication pendant une période d’un an à partir de la date d’achat.
Règles de sécurité........................................................................................................................................................................ 1. Déballer votre ventilateur........................................................................................................................................................... 2. Installation du ventilateur..............................................................................................................
1. Pour rèduire les risques de décharge électrique, s'assurer que l'électricité est coupée au disjoncteur ou au boîtier de fusibles avant de commencer. 2. Tous les càblages doivent se conformer au Code National de électricite ét aux normes électriques locales. L'installation électrique doit être effectuée par un électricien licencié qualifie. 3. Le boîtier de prise et son support doivent être attachés correctement et capables de supporter fiablement un poids minimum de 15.8 kg (35 livres).
2 5 8 12 9 1 3 10 13 a b 6 7 4 11 14 c Déballez votre ventilateur et vérifiez le contenu de l'emballage. Vous devriez trouver les éléments suivants: 1. 2. 3. 4. 5. 6. 7. Ensemble de lames (4) Assemblage du baldaquin Assemblage de boule et de tiges Couvercle de collier Assemblage du moteur de ventilateur Plaque de montage Ensemble de supports pour lames (4) 8. 9. 10. 11. 12. 13.
Outils nécessaires Plafond en pente ayant un angle de 24º au maximum Tournevis Phillips, tournevis à lame plate, clé réglable, marchepied et couteau à fil. Options de montage S'il n'existe pas de boîtier de montage, il faut lire les instructions suivantes. fusibles ou en coupant les disjoncteurs. Débrancher le courant en retirant les.
Installation du Ventilateur de Plafond Insérer avec prudence la tige d'accrochage à travers les trous situés dans le collet et dans la tige de suspension. Soyez prudent de ne pas coincer la tige contre le câblage électrique situé à l'intérieur de la tige de suspension. N'OUBLIEZ PAS de couper le courant.
Effectuer les Connexions Électriques AVERTISSEMENT Support d'accrochage Câble de sécurité Baldaquin de plafond Schéma 8 POUR ÉVITER TOUS RISQUES DE CHOC ÉLECTRIQUES, ASSUREZ-VOUS DE COUPER LE COURANT AU PANNEAU ÉLECTRIQUE PRINCIPAL AVANT D'EFFECTUER LES CONNEXIONS. REMARQUE REMARQ QUE LE VENTILATEUR DOIT ÊTRE INSTALLÉ À UNE DISTANCE MAXIMUM DE 6 MÈTRES (20 PI) DE L'APPAREIL TRANSMETTEUR POUR UNE TRANSMISSION DU SIGNAL ADÉQUATE ENTRE L'APPAREIL ÉMETTEUR ET LE RÉCEPTEUR DU VENTILATEUR.
Support de montage N'UTILISEZ PAS CE VENTILATEUR AVEC UNE COMMANDE MURALE D'INTENSITÉ D'ÉCLAIRAGE. AVERTISSEMENT Télécommande NOIR Receveuse NOIR BLEU BLANC Schéma 10 VERT BLANC BLANC BLEU NOIR VÉRIFIEZ QUE TOUS LES RACCORDEMENTS DE FILS SOIENT BIEN SERRÉS, Y COMPRIS LA MISE À LA TERRE. ASSUREZ-VOUS ÉGALEMENT QU'AUCUN FIL NE SOIT VISIBLE AU NIVEAU DES CAPUCHONS DE CONNEXION, À LA SEULE EXCEPTION DU CONDUCTEUR DE TERRE.
Terminer L'installation Etape 1. Arrangez les connexions à l'interieur de la boîte de câblage. Étape 2. Faites glisser la cache de plafond sur le crochet de suspension et placez les trous sur la cache de plafond au-dessus des vis sur le crochet de suspension. Tournez la cache de plafond jusqu'à ce qu'il se verrouille en place à la section étroite des trous de vis. (Schéma 12) Étape 3.
Fixation des Pales du Ventilateur Etape 1. Fixez les pales aux supports de pales à l'aide des vis et des rondelles en fibresfournies comme montré Schéma 14. Engagez une vis dans le support, mais ne serrez pas. Répétez cette opération pour les 2 autres vis et rondelles. Étape 2. Resserrer chaque vis fermement, tout en vous assurant que la pale est droite. Étape 3. Fixer la pale et son mécanisme d'ancrage au moteur en utilisant les vis déjà installées dans le boîtier du moteur. (Schéma 11) Étape 4.
Instalación de la Bateria REMARQUE: Avant de commencer l'installation, débranchez l'alimentation en coupant le disjoncteur ou en retirant le fusible au tableau de fusibles. Eteindre à l'aide de l'interrupteur du ventilateur n'est pas suffisant pour éviter les électrocutions. Coloque 12V bateria (incluidas). Para evitar estropeos del transmisor, extreiga la bateria cuando esté no se usa por periodo relativamente largo. (Schéma 17) Étape 1.
Remettez le courant au ventilateur du plafond et Les réglages de vitesse pour les températures chaudes et froides dépendent de plusieurs facteurs testez son bon fonctionnement. tels que la taille de la pièce, la hauteur du 1. Boutons , et : plafond, le nombre de ventilateurs, u asi Ces trois boutons sont utilisés pour régler la sucesivamente. vitesse du ventilateur comme suit : = Vitesse faible Le commutateur d'inversion est situé au boîtier = Vitesse moyenne supérieur.
Installer le Support de Télécommande Voici quelques suggestions pour vous aider à préserver votre ventilateur. Fixez le support télécommande à l'aide le vis de montage du support d'émetteur. (Schéma 21) 1. À cause du mouvement naturel du ventilateur, certaines connexions peuvent se desserrer. Vérifier les connexions de soutien, les supports et les attaches des ailettes deux fois par an. S'assurer que tout est bien attaché. (II n'est pas nécessaire de démonter le ventilateur du plafond).
Problème Solution Le ventilateur ne démarre pas. 1. Vérifier les fusibles des circuits ou les disjoncteurs. 2. Vérifier les connexions des fils d'alimentation du ventilateur et les connexions des fils d'interrupteur dans le boîtier de l'interrupteur. ATTENTION: S'assurer que le secteur est coupé. Le ventilateur est bruyant. 1. S'assurer que toutes les vis du boîtier du moteur sont serrées. 2. S'assurer que les vis qui attachent le support d'ailette de ventilateur au moyeu du moteur sont serrées. 3.
TAILLE DU VENTILATEUR 56" (142 cm) VOLTS AMPERES WATTS OURS/ MINUE CFM POIDS NET POIDS BRUT Petite 120 0.23 12.02 56 2250.56 Grande 120 0.56 66.8 148 6255.84 20.06 lbs 22.11 lbs VITESSE 1.89' Ces valeurs sont approchées. Elles ne comprennent pas les intensités de courant et les puissances utilisées par le kit de lampe. c 2019 Progress Lighting, Inc. 701 Millennium Blvd Greenville, SC 29607 All Rights Reserved 13.
Manual de Instalación del Ventilador de Techo 93114642_A P250010
Garantía limitada de por vida Se garantiza al comprador original que los motores de los ventiladores de Progress Lighting no presentan defectos mecánicos o eléctricos por el tiempo durante el cual el comprador original sea dueño del ventilador. Los interruptores de cadena, interruptores de reversa, capacitores y acabados de metal cuentan con garantía libre de defectos de materiales o mano de obra por 1 año a partir de la fecha de compra.
Normas de seguridad .......................................................................................................................................................................1. Cómo desembalar el ventilador ...................................................................................................................................................... 2. Cómo instalar el ventilador ..............................................................................................................
1. Para disminuir el riesgo de descarga eléctrica, asegúrate de que la 9. Todos los tornillos colocados se deben verificar y ajustar donde sea necesario antes de la instalación. electricidad ha sido apagada en el cortacircuitos o la caja de fusibles antes de comenzar la instalación. 10. Adecuado para uso con de control de velocidad de estado solido. 2. Todo el cableado debe cumplir con el Código Nacional de Electricidad "ANSI/NFPA 70-1999" y con los códigos locales de electricidad.
2 5 8 12 9 1 3 10 13 a b 6 4 7 11 14 c Desembalar el ventilador y revisar el contenido. Debe tener los siguientes elementos: 1. Juego de aspas (4) 2. Escudete superior 3. Conjunto de bola/tubo de suspensión 4. Cubridor del motor 5. Conjunto de motor del ventilador 6. Plato de montaje 7. Juego de soporte de fijación a aspas (4) 8. Cubierta decorativa 9. Tuerca decorativa 10. Receptor + 6 tuercas de cable 11. Transmisor + soporte + 2 tornillos de montaje 12. Bateria de 12V 13.
Herramienta necesarias Angulo máximo en el techo: 24° Destornillador Phillips, destornillador normal, llave de tuercas ajustable, escalera de tijera, y cortadoras de alambre. Opciones de instalación Si no hay una caja con cUL registración de montaje existente, sirvase leer las siguientes instrucciones. Desconectar el suministro de electricidad removiendo los fusibles o desactivando los cortacircuitos. Asegurar la caja de distribución directamente a la estructura del edificio.
Paso 1. Retire la tapa embellecedora del fondo del cobertor girando la tapa en sentido de las agujas del reloj. (Fig. 5) superior de la caja del motor (Fig. 7) Introduzca con cuidado el pasador de suspensión a través de los agujeros del cuello y de la barra. Tenga cuidado de que el pasador no se atasque con los hilos de dentro de la barra.
Soporte de montaje Cable de Seguridad Caja de techo Figura 8 5. Realice las Conexiones Electricas 1. (Figura 10) Instale el receptor en la abrazadera de montaje, el lado plano debe quedar hacia arriva. ADVERTENCIA 2. (Figura 11) Conecciones del motor a el receptor: Conecte el alambre negro del abanico a el alambre negro marcado "al Motor L" del receptor. Conecte el alambre blanco del abanico a el alambre blanco marcado "al Motor N" del receptor.
Soporte de montaje NO UTILIZAR REGULADOR DE VOLTAJE DE ILUMINACIÓN PARA PARED. CIRCUITO DE SUMINISTRO NEGRO ADVERTENCIA COMPRUEBE SI TODAS LAS CONEXIONES ESTÁN SEGURAS, INCLUYENDO LA DE TIERRA, Y QUE NO HAYA CABLES PELADOS EXPUESTOS A LAS TUERCAS DE LOS CABLES. EXCEPTO EL CABLE DE TIERRA.
Terminando la Instalación Paso 1. Meta las conexiónes en forma ordenada adentro de la toma de corriente. Paso 2. Deslice la cubierta hacia arriba hacia el soporte de montaje y coloque el agujero de posición de la cubierta sobre el tornillo del soporte de montaje, gire la cubierta hasta que quede encajada en su lugar en la sección estrecha de los agujeros de posición. (Fig. 12) Paso 3.
Cómo montar las aspas del ventilador Paso 1. Se pegan las palas a los soportes usando los tornillos y las arandelas de goma provistos como indicado en Fig 14. Inserta un tornillo en el soporte sin apretarlo. Repite el paso por los otros 2 tornillos y arandelas. Paso 2. Apreta todos los tornillos fimemente empezando con el tornillo cortador. Asgúrate de que la pala esté recta. Paso 3. Alinie los agujeros de la abrazadera con los del motor y asegurela con los tornillos suministrados.
PRECAUCIÓN: Antes de comenzar con la instalación, desconecte la alimentación apagando el circuito del automático o quitando el fusible de la caja de fusibles. Para evitar descargas eléctricas, no basta con apagar la alimentación utilizando el interruptor del ventilador. Instalación de la Bateria Instala una batería de 12V (incluida) en el control remoto. Para prevenir daños al control remoto, sacala batería si no va a usarse por largo tiempo. (Fig. 17) Paso 1.
Conecte la eléctricidad a el ventilador y confirme que opera debidamente. 1. Los bottones , , : Estos tres botones son usados para seleccionar las velocidades del ventilador de la manera siguiente: = Velocidad Alta = Velocidad Mediana = Velocidad Baja 2. El boton " " es para prender y apagar la luz, tambien se usa para controlar la intensidad de la luz. Apriete y sostenga el boton hasta obtener la intensidad de luz deseada.
Cómo Instalar el Soporte del Control Remoto He aqui algunas sugerencias para ayudarle el mantenimiento del ventilodor. Sujeta el soporte del control remoto tornillos de montaje del soporte del control remoto. (Fig. 21) 1. Debido al movimiento natural del ventilador, algunas conexiones se podrian aflojar. Examinar las conexiones del soporte, soportes, y accessorios de las aspas dos veces al año. Asgurarse de que estén seguros. (No es necesario retirar el venitlador del techo).
Problema Solución El ventilador no arranca. 1. Revisar los fusibles o interruptores de circuitos. 2. Verificar las conexiones de cables de linea al ventilador y conexiones de cable del interruptor. PRECAUCIÓN: Asegurarse de que la fuente pricipal de electricidad esté desactivada. 3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency. El ventilador hace mucho ruido. 1. Asegurarse de que todos los tornillos de la cubierta del motor estén ajustados. 2.
Tamaño del Ventilador 56" (142 cm) Velocidad Voltios Amperios Vatios RPM CFM N.W. G.W. C.F. Baja 120 0.23 12.02 56 2250.56 120 0.56 66.8 148 6255.84 22.11 lbs 1.89' Alta 20.06 lbs Estas son mediciones aproximadas. No incluyen los Amperios y vatios usado por el juego de iliminación. c 2019 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 All Rights Reserved 13.