www.proform.com Model No. PFTL39110.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, DO NOT CONTACT THE STORE; please contact Customer Care. IMPORTANT: Please register this product (see the limited warranty on the back cover of this manual) before contacting Customer Care. 1-888-533-1333 CALL TOLL-FREE: Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT ON THE WEB: www.proformservice.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems. or more amps.
20. The pulse sensor is not a medical device. Various factors, including the user's movement, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general. 25. 21. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 19.) You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.
BEFORE YOU BEGIN Thank you for selecting the new PROFORM® ZT3 treadmill. The ZT3 treadmill offers a selection of features designed to make your workouts at home more effective. And when youʼre not exercising, the unique treadmill can be folded up, requiring less than half the floor space of other treadmills. ing this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us.
ASSEMBLY To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of the walking belt or to the shipping carton.
1. Have a second person hold the Base (85) in the position shown. 1 Identify the Right Upright (78), which has a square hole near the lower end. 78 Orient the Right Upright (78) as shown, and attach it to the Base (85) with two 3/8" x 2 1/4" Bolts (8) and two 3/8" Star Washers (9); do not tighten the Bolts yet. 85 2. Orient the Left Upright (77) as shown, and attach it to the Base (85) with two 3/8" x 2 1/4" Bolts (8) and two 3/8" Star Washers (9); do not tighten the Bolts yet.
4. Raise the Uprights (77, 78), and position the Base (85) near the treadmill as shown. 4 See the far right drawing. Tie the wire tie in the lower end of the Right Upright (78) around the Upright Wire (74). Then, pull the other end of the wire tie until the Upright Wire is routed through the Right Upright. 74 Wire Tie 78 77 74 Large Hole Make sure that the end of the Upright Wire (74) does not fall into the Right Upright (78). Wire Tie 85 5. See the left inset drawing.
6. See the left inset drawing. Identify the outer side of the remaining Frame Spacer (79). 6 Hold the Frame Spacer (79) between the Left Upright (77) and the Lift Frame (65), with the outer side of the Frame Spacer facing the Left Upright. Attach the Left Upright to the Lift Frame with a 3/8" x 2 1/2" Bolt (1), a 3/8" Washer (10), and a 3/8" Nut (13); do not tighten the Bolt yet. 77 1 10 79 79 13 65 Outer Side 77 13 1 10 79 Inner Side 7.
8. Insert the wires into the Right Upright (78). Next, insert the brackets on the console assembly into the Right Upright and the Left Upright (77). Be careful not to pinch any wires. 8 Attach the console assembly with four 5/16" x 3/4" Bolts (2) and four 5/16" Star Washers (5). Start all four Bolts, and then firmly tighten each of them. Console Assembly 2 5 5 78 9. Set the Left Handrail (69) and the Right Handrail (71) on a level surface.
. Hold the handrail assembly near the console assembly. Connect the wire harness extending from the handrail assembly to the wire harness extending from the console assembly. See the inset drawing in step 6. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER.
13. Lower the Uprights (77, 78) as shown. See the inset drawing. Position the Uprights (77, 78) so that the Frame (55) is centered between the Uprights. 13 Firmly tighten the 3/8" x 2 1/2" Bolt (1) and then tighten the 3/8" x 2 1/4" Bolts (8) on each side of the treadmill. Do not overtighten the 3/8" x 2 1/2" Bolts. 55 View from Above 55 14 21 Press the indicated Grommet (21) into the Right Upright (78). Raise the Right Upright (78) and the Left Upright (not shown).
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT that is properly installed and grounded in accordance with all local codes and ordinances. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets. Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will cause excessive wear.
CONSOLE DIAGRAM Key Clip FEATURES OF THE CONSOLE IMPORTANT: If there is a sheet of plastic on the face of the console, remove the plastic. To prevent damage to the walking platform, wear clean athletic shoes while using the treadmill. The first time the treadmill is used, observe the alignment of the walking belt, and center the walking belt if necessary (see page 21). The treadmill console offers a selection of features designed to make your workouts more effective.
HOW TO TURN ON THE POWER HOW TO USE THE MANUAL MODE IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before turning on the power. If you do not do this, you may damage the console displays or other electrical components. Plug in the power cord (see page 13). Next, locate the power switch on the treadmill frame near the power cord. Make sure that the switch is in the reset position. 1. Insert the key into the console.
4. Change the incline of the treadmill as desired. calories you have burned, or the speed of the walking belt. Press the Display button repeatedly until the upper display shows the information that you are most interested in viewing. Note: While information is shown in the upper display, the same information will not be shown in the lower left or lower right display. To change the incline of the treadmill, press the Incline increase and decrease buttons or one of the numbered Quick Incline buttons.
HOW TO USE A PRESET APPLICATION indicates the speed setting for the current segment. At the end of each segment, a series of tones will sound and the next segment of the profile will begin to flash. If a different speed and/or incline setting is programmed for the next segment, the speed and/or incline setting will flash in the display to alert you. The treadmill will then automatically adjust to the speed and incline settings for the next segment. 1. Insert the key into the console.
THE INFORMATION MODE An E for English miles or an M for metric kilometers will appear in the lower right display. Press the Speed increase button to change the unit of measurement, if desired. The console features an information mode that keeps track of treadmill usage information and allows you to select a unit of measurement for the console. You can also turn on and turn off the display demo mode. The console features a display demo mode, designed to be used if the treadmill is displayed in a store.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL HOW TO MOVE THE TREADMILL To avoid damaging the treadmill, adjust the incline to the lowest position before you fold the treadmill. Then, remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. Before moving the treadmill, fold it as described at the left. CAUTION: Make sure that the latch pin is fully inserted into the platform cushion.
TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 13).
Locate the Reed Switch (46) and the Magnet (44) on the left side of the Pulley (43). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (20), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading. 1/8 in.
EXERCISE GUIDELINES WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems. The pulse sensor is not a medical device. Various factors may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general. These guidelines will help you to plan your exercise program.
PART LIST—Model No. PFTL39110.0 Key No. Qty.
17 28 38 58 31 12 27 60 59 20 57 34 19 39 27 12 17 61 28 31 56 40 20 12 27 38 34 19 20 20 41 36 15 18 34 27 55 54 27 22 42 45 46 43 20 44 37 20 33 48 27 49 40 47 18 20 15 22 14 12 30 41 42 34 33 53 12 27 52 51 12 30 50 27 EXPLODED DRAWING A—Model No. PFTL39110.
EXPLODED DRAWING B—Model No. PFTL39110.
EXPLODED DRAWING C—Model No. PFTL39110.
EXPLODED DRAWING D—Model No. PFTL39110.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.