www.proform.com Model No. PFEL08011.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, DO NOT CONTACT THE STORE; please contact Customer Care. IMPORTANT: Please register this product (see the limited warranty on the back cover of this manual) before contacting Customer Care. CALL TOLL-FREE: 1-888-533-1333 Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT ON THE WEB: www.proformservice.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your elliptical before using your elliptical. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 9. The elliptical should not be used by persons weighing more than 300 lbs. (136 kg). 1. Before beginning any exercise program, consult your physician.
BEFORE YOU BEGIN Thank you for selecting the revolutionary PROFORM® 710 E elliptical. The 710 E elliptical provides an impressive selection of features designed to make your workouts at home more effective and enjoyable. manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual. For your benefit, read this manual carefully before you use the elliptical.
PART IDENTIFICATION CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it has been preassembled. Extra parts may be included.
ASSEMBLY • To hire an authorized service technician to assemble the elliptical, call 1-800-445-2480. • In addition to the included tool(s), assembly requires the following tools: • Assembly requires two persons. one Phillips screwdriver • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you complete all assembly steps. one rubber mallet Assembly may be easier if you have your own set of wrenches.
3. With the help of a second person, place some of the packing materials (not shown) under the front of the Frame (1). Have the second person hold the Frame to prevent it from tipping while you complete this step. 3 6 105 104 Attach the Front Stabilizer (6) to the Frame (1) with two M10 x 122mm Button Screws (104) and two M10 Split Washers (105). Remove the packing materials from under the front of the Frame (1). 1 4. Orient the Upright (4) as shown.
5. Tip: Avoid pinching the Upper Wire (110). Avoid damaging the indicated plastic tabs. Set the Upright (4) on the Frame (1). 5 Avoid pinching the Upper Wire (110) and avoid damaging the tabs Attach the Upright (4) with four M10 x 25mm Button Screws (131) and four M10 Split Washers (105). 4 131 110 105 131 1 105 Tabs 6. Using a plastic bag to keep your fingers clean, apply some of the included grease to the Pivot Axle (35) and to two 16mm Wave Washers (54).
7. Identify the Right Upper Body Arm (61), which is marked with a “Right” sticker, and orient it as shown. 7 Slide the Right Upper Body Arm (61) onto the Right Upper Body Leg (60). Attach the Right Upper Body Arm (61) with two M8 x 38mm Button Bolts (96) and two M8 Locknuts (102). Make sure that the Locknuts are in the hexagonal holes. 47 Hexagonal Holes Repeat this step for the Left Upper Body Arm (47). 60 102 61 96 8. Untie and discard the wire tie on the Upper Wire (110).
9. Tip: Avoid pinching the wires. Attach the Console (7) to the Upright (4) with four M4 x 16mm Screws (101). 9 7 Avoid pinching the wires 101 4 101 10. Identify the Right Pedal Arm (58), which is marked with a “Right” sticker, and orient it as shown. 10 44 49 Attach a Pedal (49) to the Right Pedal Arm (58) with four M6 x 12mm Button Screws (103). Repeat this step for the Left Pedal Arm (44) and the other Pedal (49).
. Orient the Right Pedal Arm (58) as shown. 11 Apply grease to the axle on the Right Pedal Arm (58). Attach the Right Pedal Arm (58) to the Right Roller Arm (59) with an M8 x 13mm Button Screw (82), a Small Axle Cover (55), and an M8 Washer (97). Repeat this step for the Left Pedal Arm (44). 44 82 59 55 97 58 Grease 12. Apply a small amount of grease to one of the Pedal Arm Axles (64).
13. Orient the Rear Upright Cover (81) as shown. 13 Attach the Rear Upright Cover (81) to the Upright (4) with four M4 x 16mm Screws (101). 117 Orient the Front Upright Cover (117) as shown. Attach the Front Upright Cover (117) around the Upright (4) by pressing the hooks on the Rear Upright Cover (81) onto the tabs on the Front Upright Cover. 101 4 81 14. Identify the Right Upper Body Arm Front Cover (65), which is marked with a “Right” sticker, and orient it as shown.
15. Identify the Right Upper Body Leg Inner Cover (83), which is marked with a “Right” sticker, and orient it as shown. 15 Attach the Right Upper Body Leg Inner Cover (83) to the Right Upper Body Leg (60) with an M4 x 16mm Screw (101) and an M5 Washer (132). Identify the Right Upper Leg Outer Cover (69), which is marked with a “Right” sticker and orient it as shown.
17. Orient the Rear Console Cover (80) as shown. 17 79 Attach the Rear Console Cover (80) to the Upright (4) with two M4 x 16mm Screws (101). Orient the Front Console Cover (79) as shown. 101 Attach the Front Console Cover (79) around the Upright (4) by pressing the hooks on the Rear Console Cover (80) onto the tabs on the Front Console Cover. 4 80 18. Make sure that all parts are properly tightened before you use the elliptical. Note: After assembly is completed, extra parts may be left over.
HOW TO USE THE ELLIPTICAL HOW TO PLUG IN THE POWER CORD A temporary adapter may be used to connect the power cord to a 2-pole receptacle as shown at the right if a properly grounded outlet is not available. This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The power cord has a plug with a grounding pin.
HOW TO MOVE THE ELLIPTICAL HOW TO EXERCISE ON THE ELLIPTICAL Due to the size and weight of the elliptical, moving it requires two persons. Stand in front of the elliptical, hold the upright, and place one foot against one of the wheels. Pull on the upright and have a second person lift the handle until the elliptical will roll on the wheels. Carefully move the elliptical to the desired location, and then lower it to the floor.
CONSOLE DIAGRAM FEATURES OF THE CONSOLE The advanced console offers an array of features designed to make your workouts more effective and enjoyable. When you use the manual mode of the console, you can change the resistance of the pedals and the incline of the ramp with the touch of a button. While you exercise, the console will display continuous exercise feedback. You can also measure your heart rate using the handgrip heart rate monitor.
HOW TO TURN ON THE POWER 3. Change the resistance of the pedals and the incline of the ramp as desired. IMPORTANT: If the elliptical has been exposed to cold temperatures, allow it to warm to room temperature before you turn on the power. If you do not do this, you may damage the console displays or other electrical components. Plug in the power cord (see HOW TO PLUG IN THE POWER CORD on page 15). Next, locate the power switch on the frame near the power cord. Press the power switch to the reset position.
Incline—This display mode will show the incline level of the ramp for a few seconds each time the incline level changes. As you exercise, the workout intensity level bar will indicate the approximate intensity level of your exercise. Pulse—This display mode will show your heart rate when you use the handgrip heart rate monitor (see step 5 on page 19). Resistance (Resist.)—This display mode will show the resistance level of the pedals for a few seconds each time the resistance level changes.
When your pulse is detected, a heart symbol in the calorie display will flash each time your heart beats, one or two dashes will appear, and then your heart rate will be shown. For the most accurate heart rate reading, hold the contacts for at least 15 seconds. HOW TO USE AN ONBOARD WORKOUT 1. Begin pedaling or press any button on the console to turn on the console. See HOW TO TURN ON THE POWER on page 18. If the display does not show your heart rate, make sure that your hands are positioned as described.
At the end of each segment of the workout, a series of tones will sound and the next segment of the profile will begin to flash. If a different resistance level, ramp incline level, and/or target rpm is programmed for the next segment, the resistance level, ramp incline level, and/or target rpm will appear in the display for a few seconds to alert you. The resistance of the pedals and the incline level of the ramp will then change.
5. Select an iFit Live workout. During a competition workout, the Competition tab will show your progress in the race. As you race, the top line in the matrix will show how much of the race you have completed. The other lines will show other competitors. The end of the matrix represents the end of the race. To select an iFit Live workout, press one of the iFit Live buttons. Note: Before some workouts will download, you must go to www.iFit.com and add them to your schedule.
HOW TO CHANGE CONSOLE SETTINGS If no module is connected, the display will show the words NO IFIT MODULE. If no module is connected, go to step 10. The console features a user mode that allows you to view usage information, select a unit of measurement, and adjust the contrast level of the display. 6. Select an audio setting for the voice of the personal trainer if desired.
MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the elliptical regularly. Replace any worn parts immediately. HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. See EXPLODED DRAWING C on page 31.
See EXPLODED DRAWING C on page 31. Remove the M4 x 19mm Screws (5) and the M4 x 48mm Screw (107) from the Left and Right Shields (73, 74). Then, remove the Right Shield. HOW TO ADJUST THE DRIVE BELT If the pedals slip while you are pedaling, even while the resistance is adjusted to the highest level, the drive belt may need to be adjusted. Next, locate and loosen the Idler Screw (89). Next, tighten the Belt Adjustment Screw (91) until the Drive Belt (113) is tight. Then, retighten the Idler Screw.
EXERCISE GUIDELINES Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone.
PART LIST Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 1 1 1 8 1 1 1 1 1 1 1 1 1 1 2 2 1 1 2 4 1 1 1 1 1 1 1 1 2 2 1 2 2 1 2 1 1 1 2 2 1 2 1 1 1 1 1 2 1 Model No. PFEL08011.0 R1111A Description Key No. Qty.
Key No. Qty. 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 39 12 8 4 8 3 1 2 2 1 1 1 1 4 1 2 1 1 1 1 6 1 1 Description Key No. Qty.
31 30 121 121 21 33 101 114 3 21 104 16 114 21 101 2 106 133 134 15 121 105 121 10 141 33 31 30 101 120 122 134 133 135 124 99 127 88 25 28 1 129 41 24 27 126 89 125 43 82 101 142 123 90 40 136 84 115 109 130 128 26 102 101 39 94 91 93 23 40 135 41 13 42 101 135 38 17 92 29 22 78 140 139 14 102 85 17 20 90 12 121 134 48 11 21 108 86 137 138 101 19 113 43 6 102 34 86 101 18 105 85 135 20 50 90 108 78 109
103 52 95 76 47 103 49 96 62 95 70 102 82 53 44 101 97 97 64 101 56 77 132 51 100 46 101 57 68 82 97 98 56 45 82 97 55 53 82 51 97 57 95 77 98 82 100 67 72 97 57 55 52 53 56 103 57 95 56 59 49 103 66 100 57 53 95 83 82 101 60 97 57 62 97 58 77 97 95 87 100 65 101 57 82 61 77 132 57 64 101 69 96 82 97 102 EXPLODED DRAWING B Model No. PFEL08011.
101 71 101 101 7 5 5 116 63 107 101 37 101 5 81 8 5 5 80 73 54 36 102 96 101 75 105 131 4 101 101 79 5 131 5 36 105 74 54 117 31 5 35 118 111 110 116 102 101 96 63 112 119 101 9 101 101 71 EXPLODED DRAWING C Model No. PFEL08011.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.