User's Manual

ManualsBrandsProForm ManualsFitness EquipmentProForm PCMC99110 - CHEST PULSE ACCURATE ACCESSORY

Heart Rate Monitor Userʼs Guide

odel No.

PCMC99110

Congratulations for purchasing the new AccuRate™

heart rate monitor, designed for accuracy, comfort, and

durability. To install and use the heart rate monitor, fol-

low the instructions in this userʼs guide. For additional

information about using the heart rate monitor with

your treadmill, refer to your treadmill userʼs manual.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following conditions: (1) this

device may not cause harmful interference, and (2) this

device must accept any interference received, includ-

ing interference that may cause undesired operation.

Changes or modifications not expressly approved by

ICON Health & Fitness, Inc. could void the userʼs au-

thority to operate this device.

WARNING

If you have an implanted medical device such

as a pacemaker, check with your physician be-

fore using the heart rate monitor.

If you have heart problems, or if you are over

60 years of age and have been inactive, do not

use pulse-driven programs.

If you are taking medication regularly, consult

your physician to find whether the medication

will affect your exercise heart rate.

Summary of content (12 pages)

PAGE 1
Heart Rate Monitor Userʼs Guide Congratulations for purchasing the new AccuRate™ heart rate monitor, designed for accuracy, comfort, and durability. To install and use the heart rate monitor, follow the instructions in this userʼs guide. For additional information about using the heart rate monitor with your treadmill, refer to your treadmill userʼs manual. This device complies with Part 15 of the FCC rules.
PAGE 2
How to Install the Receiver Before the heart rate monitor can be used, the included receiver must be installed. Pages 2 through 7 of this userʼs guide include eight sections that show how the receiver is to be installed in eight different styles of treadmills. Look at pages 2 through 7 and find the drawings that most closely resemble your treadmill. Then, follow the instructions in that section to install the receiver. Note: Your treadmill may not look exactly like the treadmills shown in the drawings.
PAGE 3
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). 1 B A 2. Peel the paper off the pad on the bottom of the Receiver (C). Turn the Receiver so the cylinder is on the side shown, and press the Receiver into the bottom of the Console Back (B) in the indicated location. Connect the Short Jumper Wire (D) to the wire on the Receiver (C). Connect the other end of the Short Jumper Wire to the PULSE jack on the back of the Console (E).
PAGE 4
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (C). 1 C B A 2. Connect the Long Jumper Wire (D) to the wire on the Receiver (E). Feed the Long Jumper Wire through the holes with the other wires as shown. Connect the other end of the Long Jumper Wire to the PULSE jack on the back of the Console (F). If there is a wire already plugged into the PULSE jack, unplug it.
PAGE 5
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (C). 2. Have a second person hold the Console Base (C) as you remove the indicated Screws (D) from the Console Base. 3. Connect the Long Jumper Wire (E) to the PULSE jack on the back of the Console (F). If there is a wire already plugged into the PULSE jack, unplug it. Feed the Long Jumper Wire through the hole in the side of the Console Base (C).
PAGE 6
Note: If you have a PROFORM® 785Pi or model number PFTL79100, please call 1-888-936-4266. 1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (E). 2. Locate the loose Pulse Wire (C) inside the Console Base (E). Connect the Pulse Wire to the wire on the Receiver (D). Next, peel the paper off the pad on the bottom of the Receiver (D).
PAGE 7
These instructions are to be used with the HealthRider® T90 with a TV. 1. Make sure that the power cord is unplugged. Remove the indicated Screws from the Console Back (A). Important: The Screws may be different lengths. Keep track of which Screws were removed from which holes. 2. Raise the Console (C) enough to view the back of the Console. Peel the paper off the pad on the bottom of the Receiver (B).
PAGE 8
How to Use the Chest Pulse Sensor such as saliva or contact lens solution, wet both electrode areas. Return the sensor unit to a position against your chest. The unique heart rate monitor is specially designed for accuracy, comfort, and durability. To get the best performance from the heart rate monitor, please read the instructions below.
PAGE 9
• If the chest pulse sensor does not function properly after you have followed all of the above instructions, the battery should be replaced in the following way: CHEST PULSE SENSOR CARE • Thoroughly dry the chest pulse sensor after each use. The chest pulse sensor is activated when the electrode areas are wetted and the chest pulse sensor is put on; the chest pulse sensor shuts off when it is removed and the electrode areas are dried.
PAGE 10
Notes: 10
PAGE 11
Notes: 11
PAGE 12
LIMITED WARRANTY ICON OF CANADA, INC., (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of one (1) year from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON.