S W A L K USE 'S Model No. 831.297340 Serial No. AL The serial number is found in the location shown below. Write the serial number in the space above for future reference. Serial Number Decal I /,---2'm, / J v EXE EO Re u I IIS PM F--- E NT O H EhP El I_-.! E ! 1-800-736-6879 > J _CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. SEARS, ROEBUCK AND CO.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS ................................................................. BEFORE YOU BEGIN ....................................................................... ASSEMBLY ............................................................................... OPERATION AND ADJUSTMENT ............................................................. HOW TO FOLD AND MOVE THE TREADMILL .................................................. TROUBLE-SHOOTING ......................................
13. Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill is not working properly.) 14. Never start the treadmill while you are standing on the walking belt. Always hold the handrails or the upper body arms while using the treadmill. ASSEMBLY on pages 5 and 6, and HOW TO MOVE THE TREADMILL on page 10.
BEFORE YOU BEGIN Thank you for selecting the new PROFORM ®CROSSWALK LM treadmill. The CROSSWALK LM treadmill combines advanced technology with innovative design to let you enjoy an excellent form of cardiovascular exercise in the convenience and privacy of your home. And when you're not exercising, the unique CROSSWALK LM can be folded up, requiring less than half the floor space of other treadmills. For your benefit, read this manual carefully before using the treadmill.
ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench and your own phillips (not included). screwdriver _ and two adjustable Extension Leg Screw (53)-2 wrenches _ _9 Latch Screw (35)-2 Handrail Nut (91)-2 Handrail Washer (92)-2 _\\\\\\\_ Handrail Bolt (90)-2 _ _ 1.
Identify the Right Handrail (7) (it may be helpful to look at the drawing on page 4). 1 Hold the Right Handrail (7) at an angle as shown and insert the upper end into the Right Upright (11). Keep the lower end of the Handrail away from the treadmill to avoid scratching the finish, Next, rotate the lower end of the Handrail to the position shown by the dotted line. 7 Make sure that the hole in the lower end of the Right Handrail (7) is aligned with the hole in the Extension Leg (34).
OPERATION AND ADJUSTMENT THE PERFORMANT LUBE TM WALKING BELT This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available. Your treadmill features a walking belt coated with PERFORMANT LUBE TM, a high-performance lubricant.
CONSOLE DIAGRAM _O_oO_ OOOO@ OOo_ PRO.FORM SPEED LED Track QUARTER 5.Bl SPEED MILE O TRAINING ZONEs TRACK © CALS / FAT CALS ON / RESET [ 1-7:321 [ 2.21 TIME DISTANCE RESET Note: If there is a thin sheet of clear plastic on the face of the console, remove it before operating the console. CAUTION: Before operating the console, read the following precautions. • Do not stand on the walking belt when turning on the power.
D until you have completed 1/4 mile. A new lap will then begin. Insert the key fully into the power switch. Inserting the key will not turn on the displays. The displays will turn on when the QN/RESET button is pressed or when the walking belt is started. Note: If you just installed batteries, the displays will already be on. © SPEED display--This display shows the speed of the walking belt, in miles per hour. TIME display--This display shows the elapsed time. SPEED ,.9.
HOW TO USE THE UPPER BODY ARMS As you exercise on the treadmill, you can hold either the handrails or the upper body arms. The upper body arms are designed to exercise your arms, shoulders, and back for a total body workout. Hold one upper body arm with each hand, and move them forward and back as you walk on the treadmill. Upper Body Arms To vary the intensity of your upper body exercise, the resistance of the upper body arms can be adjusted.
HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the storage latch is closed fully over the catch, 1. Hold the upper ends of the handrails. Place one foot on the base as shown. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill.
TROUBLE-SHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). 1. SYMPTOM: THE POWER DOES NOT TURN ON a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7).
4. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn.
CONDITIONING GUIDELINES training zone. It may also be helpful to set the speed control on the console to FAT BURN to help you maintain the proper intensity level. (See page 9.) WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with pre-existing health problems. Aerobic Exercise If your goal is to strengthen your cardiovascular system, your exercise must be "aerobic.
Training Zone Exercise to cool down. This will increase the flexibility of your muscles and will help to prevent post-exercise problems. After warming up, increase the intensity of your exercise until your pulse is in your training zone for 20 to 60 minutes. (During the first few weeks of your exercise program, do not keep your pulse in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise--never hold your breath.
PART LIST--Model Key No, Qty, 1 2 3 4 5 6 7 8 9 10" 11 12 13 14 15 16 17 18 19 20* 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 1 1 6 1 2 1 1 1 1 1 1 1 15 1 2 7 1 1 1 1 1 6 1 1 8 1 1 1 1 1 4 1 1 2 2 2 2 7 7 4 1 1 1 1 1 1 2 4 4 1 1 2 2 1 1 1 No. 831.
EXPLODED DRAWING--Model No. 831.297340 mO98A • 22 2 ...... _o_-_ 23 34 \\ 93 / / 31 25 32 36 99 39 100 89 98 56 ._ _ 26 lO: 25 67 9O 68 ....
The model number and serial number of your PROFORM _" CROSSWALK LM treadmill are listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal. Model No, 831,297340 QUESTIONS? If you find that: you need help assembling or operating the PROFORM CROSSWALK LM treadmill • a part is missing All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service Center.
