User`s manual

ManualsBrandsProForm ManualsOther370p Treadmill

Model No. PETL37905.1

Serial No.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Serial Number

Decal

ORDERING REPLACEMENT PARTS

To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:

ICON Health & Fitness, Ltd.

Customer Service Department

Unit 4, Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

Tel:

Outside the UK: (44) 113 387 7133

Fax: (44) 113 387 7125

To help us assist you, please be prepared to provide the following information:

• the MODEL NUMBER of the product (PETL37905.1)

• the NAME of the product (PROFORM 370 P treadmill)

• the SERIAL NUMBER of the product (see the front cover of this manual)

• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST and the EXPLODED DRAW-

ING in the centre of this manual)

08457 089 009

USER’S MANUAL

www.iconeurope.com

Visit our website at

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts,

please call:

Or write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road, Beeston

Leeds, LS11 8JG

email: csuk@iconeurope.com

08457 089 009

Summary of content (12 pages)

PAGE 1
ORDERING REPLACEMENT PARTS To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write: ICON Health & Fitness, Ltd. Customer Service Department Unit 4, Revie Road Industrial Estate Revie Road Beeston Leeds, LS118JG UK Model No. PETL37905.1 Serial No.
PAGE 2
CONDITIONING GUIDELINES WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems. TABLE OF CONTENTS The pulse sensor is not a medical device. Various factors, including your movement, may affect the accuracy of heart rate readings. The sensor is intended only as an exercise aid in determining heart rate trends in general. IMPORTANT PRECAUTIONS . . . . . . . . . . . . . .
PAGE 3
Locate the Reed Switch (10) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm (1/8 in.). If necessary, loosen the Screw (49), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.
PAGE 4
20. When folding or moving the treadmill, make sure that the storage latch is fully closed. maintenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorised service representative. Servicing other than the procedures in this manual should be performed by an authorised service representative only. 21. Inspect and properly tighten all parts of the treadmill regularly. 22. Never insert any object into any opening. 23.
PAGE 5
HOW TO MOVE THE TREADMILL BEFORE YOU BEGIN Before moving the treadmill, convert the treadmill to the storage position as described on page 15. Make sure that the frame is securely held by the storage latch. 1. Hold the upper ends of the handrails, and place one foot against one of the wheels. 2. Tilt the treadmill back until it rolls freely on the wheels. Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while moving the treadmill.
PAGE 6
ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance.
PAGE 7
ting are programmed for each segment. Note: The same speed setting and/or incline setting may be programmed for two or more consecutive segments. HOW TO USE A PRESET PROGRAM 1 Insert the key into the console. The speed setting for Current Segment the first segment will be shown in the flashing Current Segment column of the matrix. (The incline settings are not shown in the matrix.) The speed settings for the next three segments will be shown in the columns at the right.
PAGE 8
4. Hold the Console Base (47) near the Left Handrail (71). Attach the ends of the ground wires on the Console Base to the indicated small hole in the Left Handrail with the Silver Ground Screw (75). Speed display—This display shows the speed of the walking belt. 4 47 Ground Wires Fat/Cals display—This display shows the approximate numbers of fat calories and calories you have burned (see FAT BURNING on page 19).
PAGE 9
HOW TO TURN ON THE POWER 1 Plug in the power cord (see page 9). 2 Locate the on/off switch on the treadmill frame near the power cord. Make sure that the switch is in the “on” position. 3 To stop the walking belt, press the Stop button. The Time/Incline display will begin to flash. To restart the walking belt, press the Start button or the Speed increase button. 4 On Position To change the incline of the treadmill, press the Incline buttons.
PAGE 10
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD This product must be earthed.
PAGE 11
Key No. Qty.
PAGE 12
EXPLODED DRAWING—Model No. PETL37905.