User`s manual

22
7
7. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place; the allen wrench is used to adjust the walking belt (see page 24). To protect the
floor or carpet from damage, place a mat under the treadmill.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord. CAU-
TION: You must be able to safely lift 20 kg (45 lbs.) in order
to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown.
CAUTION: To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise the
treadmill, lift with your legs rather than your back. Raise
the treadmill halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the catch is past
the pin on the lock knob. Slowly release the latch knob.
Make sure that the catch is held securely by the pin.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sun-
light. Do not leave the treadmill in the storage position
in temperatures above 30° C (85° F).
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the catch is
held securely by the pin on the lock knob.
1. Hold the handrails and place one foot against a wheel.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce the
risk of injury, use extreme caution whilst moving the
treadmill. Do not attempt to move the treadmill over an
uneven surface.
3. Place one foot on a wheel, and carefully lower the treadmill
until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the
left and hold it. Pivot the treadmill down until the frame is past the pin. Slowly release the latch knob.
2. Refer to drawing 1 above. Hold the treadmill firmly with both hands, and slowly lower the treadmill to the floor.
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.
Base
Wheels
1
Latch
Knob
Pin
Catch
Closed
Open
2
5. See the inset drawing. Identify the Left Top Handgrip (31)
(there are identifying marks inside the Handgrips). Set the
Left Top Handgrip on the left Handgrip Extension (34).
Insert two 1/2” Screws (9) into the two holes in the
Handgrip Extension indicated by the arrows. Tighten
the Screws into the Left Top Handgrip.
Important: Do not insert the two 1/2” Screws (9) into
the wrong holes in the Handgrip Extension (34), or
tighten the Screws into the plastic bosses on the bot-
tom of the Left Top Handgrip (31).
31
Bosses
64
9
34
5
31
43
6
6. Attach the matching Left Bottom Handgrip (112) with
three 1/2” Screws (9).
Attach the Right Top Handgrip and the Right Bottom
Handgrip (not shown) as described above.
9
112
9
3
3. With the help of a second person, carefully tip the
Uprights (64) back to the vertical position.
Attach the Latch Assembly (32) to the left Upright (64)
with two Extension Screws (35).
32
35
64
35
4
4. Orient one of the Handgrip Extensions (34) as shown and
insert it as far as possible into the post on the left Upright
(64). If necessary, tap the Handgrip Extension with a rub-
ber mallet to fully insert it. Attach the Handgrip Extension
with two Extension Screws (35), one towards the front of
the post, and the other towards the back.
Attach the other Handgrip Extension to the post on the
right Upright (not shown) in the same way.
34
35
35
64
35
Post
9