Specification Sheet

ManualsBrandsPROFLO ManualsBathtubsPROFLO 60" x 32" Alcove 8 Jet Whirlpool Bath Tub with Skirt, Left Hand Drain and Left Hand Pump

Product Features

• Durable easy-care acrylic construction

• Eight adjustable color matched hydro jets,

including a lumbar jet

• Factory preset air controls for whirlpool action

• High efficiency 5.6 amp/.8 HP motor

• Textured slip-resistant bottom

• Integral tile flange

• Heater blank, safety suction and silent air

induction

• Available as an invigorating whirlpool and an

unjetted soaking bath

• Air activated on/off switch

PFW6032ALSKWH

60 x 32 Plus A Series

Whirlpool & Soaking Baths

Model Numbers

PFW6032ALSK 60” x 32” whirlpool with

integral skirt - left hand drain

PFW6032ARSK 60” x 32” whirlpool with

integral skirt - right hand drain

PFS6032LSK 60” x 32” soaking bath with

integral skirt - left hand drain

PFS6032RSK 60” x 32” soaking bath with

integral skirt - right hand drain

MIRPRESSHTR Whirlpool heater

9 1/2"

32"

16"

18"

42"

60"

32"

18 3/4"

19 3/4"

1/2"

2 1/2"

With Integral Skirt

Color Palette

• White - WH

• Biscuit - BS

General Specifications

• 60” length overall

• 32” width overall

• 19 3/4” height overall

• 40 gallon operating capacity

• 45 gallon total capacity to

overflow

• Prewired for simple plug-in

installation

• Requires a single 115V/20 amp

GFCI circuit

Recommended Parts

PF1641 PVC/ABS 17”-22” Tub depth

PF1642 PVC/ABS 23”-27” Tub depth

Warranty and Codes

This product features a 5-year limited warranty

and meets or exceeds the following standards:

Whirlpools - IAPMO PS32-84, UL listing 27E7, ANSI

Z124.1-95, ASME A112.19.8M-87R(96) and ASME

A112.19.7M-95. Baths - ANSI Z124.1-95. In an effort

to continually improve our products, design changes

may periodically be made. Ferguson reserves the

right to provide newly designed material to fill any

order unless otherwise agreed to in writing.

NOTE: All dimensions and specifications are nominal and may vary

⁄4

”.

Use actual products for accuracy in critical situations.

Installation Instructions

Never allow the weight of the tub to be supported by lip on deck or stringers, as this could result

in product failure and void the Warranty. If utilities are available, level and fill tub with water and

test for proper operation and drainage or possible water leaks due to transit/handling damage.

It is REQUIRED that the tub be supported by the tub bottom and not the tub lip. The lip should

only rest on the finished deck surface or support stringers. The tub bottom must be supported

by a setting compound such as cement or mortar (fast cure materials are not recommended

due to excessive shrinkage). Failure to use a suitable setting compound will void the warranty. A

sheet of plastic film on top of compound, is recommended as a barrier. The tub should be set in

place (do not handle whirlpool by piping) while compound is still soft so that the compound will

conform to the tub bottom. Tub should be worked down into compound so the lip of the tub just

makes contact with finished deck surface or support stringers. It may be necessary to partially

fill tub with water to aid in properly setting the tub.

Distributed Exclusively by Ferguson and Wolseley Canada

Product Specifications