Specification Sheet
®
Product Features
• Durable easy-care acrylic construction
• Eight adjustable color matched hydro jets,
including a lumbar jet
• Factory preset air controls for whirlpool action
• Textured slip-resistant bottom
• Integral tile flange
• Heater blank, safety suction and silent air
induction
• Available as an invigorating whirlpool and an
unjetted soaking bath
• Air activated on/off switch
PFW6032ALSKWH
60 x 32 Plus A Series
Whirlpool & Soaking Baths
Model Numbers
PFW6032ALSK 60” x 32” whirlpool with
integral skirt - left hand drain
PFW6032ARSK 60” x 32” whirlpool with
integral skirt - right hand drain
PFS6032LSK 60” x 32” soaking bath with
integral skirt - left hand drain
PFS6032RSK 60” x 32” soaking bath with
integral skirt - right hand drain
MIRPRESSHTR Whirlpool heater
9 1/2"
32"
16"
18"
42"
60"
32"
18 3/4"
19 3/4"
16 1/4"
1/2"
1"
2 1/2"
With Integral Skirt
Color Palette
• White - WH
• Biscuit - BS
General Specifications
• 60” length overall
• 32” width overall
• 19 3/4” height overall
• 40 gallon operating capacity
• 45 gallon total capacity to
overflow
• Prewired for simple plug-in
installation
• Requires a single 115V/20 amp
GFCI circuit
Warranty and Codes
This product features a 5-year limited warranty
and meets or exceeds the following standards:
Whirlpools - IAPMO PS32-84, UL listing 27E7, ANSI
Z124.1-95, ASME A112.19.8M-87R(96) and ASME
A112.19.7M-95. Baths - ANSI Z124.1-95. In an effort
to continually improve our products, design changes
may periodically be made. Ferguson reserves the
right to provide newly designed material to fill any
order unless otherwise agreed to in writing.
NOTE: All dimensions and specifications are nominal and may vary
±
1
⁄4
”.
Use actual products for accuracy in critical situations.
Installation Instructions
Never allow the weight of the tub to be supported by lip on deck or stringers, as this could result
in product failure and void the Warranty. If utilities are available, level and fill tub with water and
test for proper operation and drainage or possible water leaks due to transit/handling damage.
It is REQUIRED that the tub be supported by the tub bottom and not the tub lip. The lip should
only rest on the finished deck surface or support stringers. The tub bottom must be supported
by a setting compound such as cement or mortar (fast cure materials are not recommended
due to excessive shrinkage). Failure to use a suitable setting compound will void the warranty. A
sheet of plastic film on top of compound, is recommended as a barrier. The tub should be set in
place (do not handle whirlpool by piping) while compound is still soft so that the compound will
conform to the tub bottom. Tub should be worked down into compound so the lip of the tub just
makes contact with finished deck surface or support stringers. It may be necessary to partially
fill tub with water to aid in properly setting the tub.
Product Specifications
Distributed Exclusively by Ferguson and Wolseley Canada
© 2013 Ferguson Enterprises, Inc. All Right Reserved
14866 02/13
Recommended Parts
MB138882 17-22 PVC Cable drain w/ trim - BN
MB138883 17-22 PVC Cable drain w/ trim - CP
MB138884 17-22 PVC Cable drain w/ trim - ORB
MB138885 17-22 ABS Cable drain w/ trim - BN
MB138886 17-22 ABS Cable drain w/ trim - CP
MB138887 17-22 ABS Cable drain w/ trim - ORB